yes i will take off
but which of the 2 photo is correct?
first or second??
It shouldn't matter. but which of the 2 photo is correct?
first or second??
Topic: The Chili – 30+GH/s BFL based Bitcoin Miner Assembly - page 55. (Read 138054 times)
yes i will take off
but which of the 2 photo is correct?
first or second??
but which of the 2 photo is correct?
first or second??
The shiny bumpy part is the plastic that protects the thermal pad in transit. You should take it off.
OK THESE IS CORRECT OR THE SECOND PHOTO IS CORRECT?
http://www.frozencpu.com/products/image/11631/thr-84.jpg/thr-84/Fujipoly_Premium_System_Builder_Thermal_Pad_-_14_Sheet_-_150_x_100_x_05_-_Thermal_Conductivity_60_WmK.html
if you see the photo you see that one side have some like square and the other side of thermal pad does not
which side go where
which go SIDE GO TO HEATSINK OF COOLER?
Yes, but can you take a picture of it on your board as you have it mounted? if you see the photo you see that one side have some like square and the other side of thermal pad does not
which side go where
which go SIDE GO TO HEATSINK OF COOLER?
http://www.frozencpu.com/products/image/11631/thr-84.jpg/thr-84/Fujipoly_Premium_System_Builder_Thermal_Pad_-_14_Sheet_-_150_x_100_x_05_-_Thermal_Conductivity_60_WmK.html
if you see the photo you see that one side have some like square and the other side of thermal pad does not
which side go where
which go SIDE GO TO HEATSINK OF COOLER?
if you see the photo you see that one side have some like square and the other side of thermal pad does not
which side go where
which go SIDE GO TO HEATSINK OF COOLER?
which is the correct and incorrect Fujipoly SIDE
Fujipoly Extreme Thermal Pad
I MEAN ONE SIDE HAVE SOME SQUARE these side put at heatsink or at jalapeno chip
? 
Can you post a close-up picture of what you're talking about, preferably still on the board?Fujipoly Extreme Thermal Pad
I MEAN ONE SIDE HAVE SOME SQUARE these side put at heatsink or at jalapeno chip
? Thanks.
which is the correct and incorrect Fujipoly SIDE
Fujipoly Extreme Thermal Pad
I MEAN ONE SIDE HAVE SOME SQUARE these side put at heatsink or at jalapeno chip
?
Fujipoly Extreme Thermal Pad
I MEAN ONE SIDE HAVE SOME SQUARE these side put at heatsink or at jalapeno chip
? 
watching
i have artic twin turbo 2
what i must do at miner with hashing 28gh
Did you try reseating the heat sink to make sure you have good contact? what i must do at miner with hashing 28gh
i have artic twin turbo 2
what i must do at miner with hashing 28gh
what i must do at miner with hashing 28gh
do you have any version for linux?
rasperby
i have 2 chilli one hashing at 35 gh
and the other hashing at 28 gh
why that happen?
rasperby
i have 2 chilli one hashing at 35 gh
and the other hashing at 28 gh
why that happen?
28GH/s is pretty low, I would try reseating the heat sink. You still haven't replied as to what heat sink you are using, so I can't help you there.
do you have any version for linux?
rasperby
i have 2 chilli one hashing at 35 gh
and the other hashing at 28 gh
why that happen?
rasperby
i have 2 chilli one hashing at 35 gh
and the other hashing at 28 gh
why that happen?
ok it started
will see
when you will have new firmware updated?
will see
when you will have new firmware updated?
32 bit windows version
That would be your reason,
That versions for 64bit windows, I just went and made a 32 Bit for you
http://www.speedyshare.com/vgRJy/BFGMiner-Chili-32.zip
This is a workaround version of BFGMiner until a new firmware update for the chilis
Here's a modified version of BFGMiner, I also included the driver inside of it as well that should fix your problem. (I don't know much about CGMiner though)
http://www.speedyshare.com/vgRJy/BFGMiner-Chili-32.zip
Open up bfgminer.conf and change the Pool and Username to whatever you want (It currently uses mine so make sure you change it)
Run CDM v2.08.30 WHQL Certified.exe to install the correct driver for windows
Once you do both of those, just open up bfgminer.exe and it should read from the config automatically and start hashing for you.
If it doesn't see the Chili, all you have to do is keep BFGMiner open, unplug the USB, Plug it back in, press M then + then type all or auto and enter. It should find it.
Please note if it still isn't working then you need to exit BFGMiner, unplug you chili power, plug it back in and wait for all the lights to stop blinking. If you try to find the miner while it's "Booting up" it will have issues.
"Booting Up" is the two most right LEDs (Closer to the Power) blinking back and forth. Again once all the LEDs are not blinking anymore it should be ready to start hashing, start your BFGMiner and follow the above steps.
Let me know if this helps
Here's a modified version of BFGMiner, I also included the driver inside of it as well that should fix your problem. (I don't know much about CGMiner though)
http://www.speedyshare.com/vgRJy/BFGMiner-Chili-32.zip
Open up bfgminer.conf and change the Pool and Username to whatever you want (It currently uses mine so make sure you change it)
Run CDM v2.08.30 WHQL Certified.exe to install the correct driver for windows
Once you do both of those, just open up bfgminer.exe and it should read from the config automatically and start hashing for you.
If it doesn't see the Chili, all you have to do is keep BFGMiner open, unplug the USB, Plug it back in, press M then + then type all or auto and enter. It should find it.
Please note if it still isn't working then you need to exit BFGMiner, unplug you chili power, plug it back in and wait for all the lights to stop blinking. If you try to find the miner while it's "Booting up" it will have issues.
"Booting Up" is the two most right LEDs (Closer to the Power) blinking back and forth. Again once all the LEDs are not blinking anymore it should be ready to start hashing, start your BFGMiner and follow the above steps.
Let me know if this helps
32 bit windows version
ok i do and then wihich file i run?
bfgminer
does not run?
at windows
why?
bfgminer
does not run?
at windows
why?
BFGMiner.exe?
Do you have 32 or 64bit windows?
ok i do and then wihich file i run?
bfgminer
does not run?
at windows i have win 32 bit version
why?
bfgminer
does not run?
at windows i have win 32 bit version
why?
I TRY TO CONNECT to bitminter
but chilli
tell bitforce com72 error
but chilli
tell bitforce com72 error
This is a workaround version of BFGMiner until a new firmware update for the chilis
Here's a modified version of BFGMiner, I also included the driver inside of it as well that should fix your problem. (I don't know much about CGMiner though)
http://www.speedyshare.com/uKncp/BFGMiner-Chili.zip
Open up bfgminer.conf and change the Pool and Username to whatever you want (It currently uses mine so make sure you change it)
Run CDM v2.08.30 WHQL Certified.exe to install the correct driver for windows
Once you do both of those, just open up bfgminer.exe and it should read from the config automatically and start hashing for you.
If it doesn't see the Chili, all you have to do is keep BFGMiner open, unplug the USB, Plug it back in, press M then + then type all or auto and enter. It should find it.
Please note if it still isn't working then you need to exit BFGMiner, unplug you chili power, plug it back in and wait for all the lights to stop blinking. If you try to find the miner while it's "Booting up" it will have issues.
"Booting Up" is the two most right LEDs (Closer to the Power) blinking back and forth. Again once all the LEDs are not blinking anymore it should be ready to start hashing, start your BFGMiner and follow the above steps.
Let me know if this helps
Here's a modified version of BFGMiner, I also included the driver inside of it as well that should fix your problem. (I don't know much about CGMiner though)
http://www.speedyshare.com/uKncp/BFGMiner-Chili.zip
Open up bfgminer.conf and change the Pool and Username to whatever you want (It currently uses mine so make sure you change it)
Run CDM v2.08.30 WHQL Certified.exe to install the correct driver for windows
Once you do both of those, just open up bfgminer.exe and it should read from the config automatically and start hashing for you.
If it doesn't see the Chili, all you have to do is keep BFGMiner open, unplug the USB, Plug it back in, press M then + then type all or auto and enter. It should find it.
Please note if it still isn't working then you need to exit BFGMiner, unplug you chili power, plug it back in and wait for all the lights to stop blinking. If you try to find the miner while it's "Booting up" it will have issues.
"Booting Up" is the two most right LEDs (Closer to the Power) blinking back and forth. Again once all the LEDs are not blinking anymore it should be ready to start hashing, start your BFGMiner and follow the above steps.
Let me know if this helps
I TRY TO CONNECT to bitminter
but chilli
tell bitforce com72 error
but chilli
tell bitforce com72 error
Jump to: