[XPM] Working on a GPU miner for Primecoin, new thread :) - page 19.

mtrlt

member

Activity: 104

Merit: 10

Quote from: EgotisticalElf on September 04, 2013, 08:06:48 AM

Quote from: mhps on September 04, 2013, 08:01:35 AM

Quote from: cabin on September 02, 2013, 02:01:16 PM

Quote from: jaakkop on September 02, 2013, 12:32:11 PM

I'm getting "The procedure entry point clEnqueueFillBuffer could not be located in the dynamic link library" and crash. Win8 x64 & GTX 560

You need to upgrade your amd/nvidia drivers to fix that one, but it will probably still crash after that.

Same here on Win8 x64 Nvidia C2075. The driver was updated in July and should support openCL 1.1

You assume clEnqueueFillBuffer works in OCL 1.1

It seems clEnqueueFillBuffer indeed requires OpenCL 1.2. I could do without it but it's kind of a pain in the ass. Nvidia doesn't have drivers that support OpenCL 1.2?

EgotisticalElf

newbie

Activity: 13

Merit: 0

Quote from: mhps on September 04, 2013, 08:01:35 AM

Quote from: cabin on September 02, 2013, 02:01:16 PM

Quote from: jaakkop on September 02, 2013, 12:32:11 PM

I'm getting "The procedure entry point clEnqueueFillBuffer could not be located in the dynamic link library" and crash. Win8 x64 & GTX 560

You need to upgrade your amd/nvidia drivers to fix that one, but it will probably still crash after that.

Same here on Win8 x64 Nvidia C2075. The driver was updated in July and should support openCL 1.1

You assume clEnqueueFillBuffer works in OCL 1.1

mhps

hero member

Activity: 516

Merit: 500

CAT.EX Exchange

Quote from: cabin on September 02, 2013, 02:01:16 PM

Quote from: jaakkop on September 02, 2013, 12:32:11 PM

I'm getting "The procedure entry point clEnqueueFillBuffer could not be located in the dynamic link library" and crash. Win8 x64 & GTX 560

You need to upgrade your amd/nvidia drivers to fix that one, but it will probably still crash after that.

Same here on Win8 x64 Nvidia C2075. The driver was updated in July and should support openCL 1.1

DeaDTerra

donator

Activity: 1064

Merit: 1000

Quote from: paulthetafy on September 04, 2013, 07:59:33 AM

you're absolutely certain you have the user/pass/IP/port correct, as per your primecoin.conf for the QT? I found it crashed if it couldn't getwork from the rpc server

It is working and it is getting work from the QT

It starts to look for prime numbers and finds one/two chains but then it crashes after a couple of seconds.
//DeaDTerra

paulthetafy

hero member

Activity: 820

Merit: 1000

you're absolutely certain you have the user/pass/IP/port correct, as per your primecoin.conf for the QT? I found it crashed if it couldn't getwork from the rpc server

DeaDTerra

donator

Activity: 1064

Merit: 1000

I can't turn the fermat test off because then it crashes straight on start and I get fraction assserts error.
I have gotten the program to work for roughly 30-45 sec then it crashes.
I have 2x7990 and I am running all 4 cores.
I have the latest drivers and I run on windows 7 64 bits.
I have the following settings

host 127.0.0.1
port 9332
user username
pass password

protocol primecoin

worksize 256
aggression 16
sievepercentage 10
sievesize 1000000

primecoin_address AbJSsYd5cnj2MxmBEHxtWo8kwpt7qA77xM
debug false
opencldebug false
cpu_mining_threads 4
use_gpu true
use_gpu_fermat_test true
getwork_rate 1000

Any suggestions on how to fix it?

//DeaDTerra

bitwarrior

legendary

Activity: 1764

Merit: 1000

Have you tried decreasing the sievesize to 1000000, the percent to 10, and probably more importantly, increasing the worksize to 256?

Yes, its just slowed the time before it hits the appcrash.. let me try those 3 variables all at the same time.

Nope.. same results.. still appcrash..

paulthetafy

hero member

Activity: 820

Merit: 1000

Quote from: bitwarrior on September 04, 2013, 07:39:08 AM

Quote from: mtrlt on September 04, 2013, 03:20:54 AM

Yes it had the wrong source file. It's fixed now, please redownload.

Quote from: bitwarrior on September 04, 2013, 02:14:31 AM

Hey Mtrlt,

Any info on how to fix the appcrash? seems many of us here are experiencing that.

I have no idea why it happens. Post your config.

windows 7 64-bit AMD Radeon 7970 Already upgraded to Catalyst 13.8

host 127.0.0.1
port 9914
user user
pass pass

protocol primecoin

worksize 64
aggression 24
sievepercentage 15
sievesize 25165824

primecoin_address xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
debug false
opencldebug false
cpu_mining_threads 4
use_gpu true
use_gpu_fermat_test true
getwork_rate 4000

//////////////////////////////////////////////////// already tried the HP7 and HP10 XPM client while the reaper is mining.

With this beta 2 , I can see the new info of
number of candidates found

But still crashes due to integer overflow as per the provided error

Problem Event Name:   APPCRASH
  Application Name:   reaper.exe
  Application Version:   0.0.0.0
  Application Timestamp:   5226da9a
  Fault Module Name:   reaper.exe
  Fault Module Version:   0.0.0.0
  Fault Module Timestamp:   5226da9a
  Exception Code:   c0000095
  Exception Offset:   0002621a

  Locale ID:   1033
  Additional Information 1:   13a8
  Additional Information 2:   13a84480b0d9c766a5e4c95aa1171a8d
  Additional Information 3:   13a8
  Additional Information 4:   13a84480b0d9c766a5e4c95aa1171a8d

Have you tried decreasing the sievesize to 1000000, the percent to 10, and probably more importantly, increasing the worksize to 256?

bitwarrior

legendary

Activity: 1764

Merit: 1000

Quote from: mtrlt on September 04, 2013, 03:20:54 AM

Yes it had the wrong source file. It's fixed now, please redownload.

Quote from: bitwarrior on September 04, 2013, 02:14:31 AM

Hey Mtrlt,

Any info on how to fix the appcrash? seems many of us here are experiencing that.

I have no idea why it happens. Post your config.

windows 7 64-bit AMD Radeon 7970 Already upgraded to Catalyst 13.8

host 127.0.0.1
port 9914
user user
pass pass

protocol primecoin

worksize 64
aggression 24
sievepercentage 15
sievesize 25165824

primecoin_address xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
debug false
opencldebug false
cpu_mining_threads 4
use_gpu true
use_gpu_fermat_test true
getwork_rate 4000

//////////////////////////////////////////////////// already tried the HP7 and HP10 XPM client while the reaper is mining.

With this beta 2 , I can see the new info of
number of candidates found

But still crashes due to integer overflow as per the provided error

Problem Event Name:   APPCRASH
  Application Name:   reaper.exe
  Application Version:   0.0.0.0
  Application Timestamp:   5226da9a
  Fault Module Name:   reaper.exe
  Fault Module Version:   0.0.0.0
  Fault Module Timestamp:   5226da9a
  Exception Code:   c0000095
  Exception Offset:   0002621a

  Locale ID:   1033
  Additional Information 1:   13a8
  Additional Information 2:   13a84480b0d9c766a5e4c95aa1171a8d
  Additional Information 3:   13a8
  Additional Information 4:   13a84480b0d9c766a5e4c95aa1171a8d

cosurgi

sr. member

Activity: 298

Merit: 250

ermm..

So is it faster than CPU? is it slower?

Is there any mining hardware comparison for primecoins?

thanks

DeaDTerra

donator

Activity: 1064

Merit: 1000

There is a lot of whining in here.
Most people don't seem to understand what a donation is,
Instead they thought about a potential gain and misunderstood this for a promised or guaranteed gain.
You have no grounds to whine on, so take it somewhere else.

I donated, the miner isn't working at all for me, constant crashes.
I was aware of the possibility of this and I did not expect anything else.
I donated to support the developer not for personal gain.

So please take the whining to another thread, so we can focus on bug reports and getting the miner to work

//DeaDTerra

mtrlt

member

Activity: 104

Merit: 10

Quote from: wyldfire on September 04, 2013, 06:51:27 AM

Quote from: bitwarrior on September 04, 2013, 02:14:31 AM

Any info on how to fix the appcrash? seems many of us here are experiencing that.

I had a crash until I patched libblkmaker to support primecoin. Have you already done that?

Crap. I thought the libblkmaker I had was already patched. I have patched the library now, everyone should redownload it: https://dl.dropboxusercontent.com/u/55025350/bitcoin-libblkmaker.zip

wyldfire

newbie

Activity: 23

Merit: 0

Quote from: bitwarrior on September 04, 2013, 02:14:31 AM

Any info on how to fix the appcrash? seems many of us here are experiencing that.

I had a crash until I patched libblkmaker to support primecoin. Have you already done that?

ivanlabrie

hero member

Activity: 812

Merit: 1000

Quote from: mtrlt on September 04, 2013, 03:20:54 AM

Yes it had the wrong source file. It's fixed now, please redownload.

Quote from: bitwarrior on September 04, 2013, 02:14:31 AM

Hey Mtrlt,

Any info on how to fix the appcrash? seems many of us here are experiencing that.

I have no idea why it happens. Post your config.

This happens on my windows system with beta 1 using cat 12.8 (64 bit win 7) on a 7970. Have no clue how to compile from windows btw.

mtrlt

member

Activity: 104

Merit: 10

Yes it had the wrong source file. It's fixed now, please redownload.

Quote from: bitwarrior on September 04, 2013, 02:14:31 AM

Hey Mtrlt,

Any info on how to fix the appcrash? seems many of us here are experiencing that.

I have no idea why it happens. Post your config.

paulthetafy

hero member

Activity: 820

Merit: 1000

Quote from: mtrlt on September 04, 2013, 02:01:55 AM

I meant to work on the miner after school but I was dead tired, went straight to sleep.

This is how I built Reaper on Ubuntu 13.04 server:

First! Redownload the miner from the link I gave you. There should be a VERSION file that says it's beta 2.

sudo apt-get install build-essential cmake libgmp-dev libcurl4-openssl-dev dh-autoreconf pkg-config libjansson-dev
download & install AMD's (or Nvidia's) OpenCL SDK

download bitcoin-libblkmaker from
https://dl.dropboxusercontent.com/u/55025350/bitcoin-libblkmaker.zip
and extract it to the directory where the miner sources are.
then do this:
{
   cd libblkmaker
   make clean
   ./autogen.sh
   make
   sudo make install
   cd ..
}

Then, just run cmake-linux.sh.

Hi mtrlt, I had beta 1 working fine on ubuntu. Now I'm getting "Error: Error getting OpenCL device IDs". I kept my old conf file so that hasn't changed. Any ideas?

edit: fixed the above my setting DISPLAY=:0

However I'm now getting

Code:

Using devices 0, 1
OpenCL device 0........
Compiling kernel... this could take up to 2 minutes.
"/tmp/OCLiKVN8G.cl", line 338: warning: nested comment is not allowed
        /*/
        ^

"/tmp/OCLiKVN8G.cl", line 672: error: too many arguments in function call
        uint16 a = Mul_512b_32b(FixedMultiplier,FermatNumbers[get_global_id(0)>>1],ORIGIN_LENGTH);
                                                                                   ^

1 error detected in the compilation of "/tmp/OCLiKVN8G.cl".

Frontend phase failed compilation.

bitwarrior

legendary

Activity: 1764

Merit: 1000

Quote from: mtrlt on September 04, 2013, 02:01:55 AM

I meant to work on the miner after school but I was dead tired, went straight to sleep.

This is how I built Reaper on Ubuntu 13.04 server:

First! Redownload the miner from the link I gave you. There should be a VERSION file that says it's beta 2.

sudo apt-get install build-essential cmake libgmp-dev libcurl4-openssl-dev dh-autoreconf pkg-config libjansson-dev
download & install AMD's (or Nvidia's) OpenCL SDK

download bitcoin-libblkmaker from
https://dl.dropboxusercontent.com/u/55025350/bitcoin-libblkmaker.zip
and extract it to the directory where the miner sources are.
then do this:
{
   cd libblkmaker
   make clean
   ./autogen.sh
   make
   sudo make install
   cd ..
}

Then, just run cmake-linux.sh.

Hey Mtrlt,

Any info on how to fix the appcrash? seems many of us here are experiencing that.

YipYip

hero member

Activity: 574

Merit: 500

mtrlt

member

Activity: 104

Merit: 10

I meant to work on the miner after school but I was dead tired, went straight to sleep.

This is how I built Reaper on Ubuntu 13.04 server:

First! Redownload the miner from the link I gave you. There should be a VERSION file that says it's beta 2.

sudo apt-get install build-essential cmake libgmp-dev libcurl4-openssl-dev dh-autoreconf pkg-config libjansson-dev
download & install AMD's (or Nvidia's) OpenCL SDK

download bitcoin-libblkmaker from
https://dl.dropboxusercontent.com/u/55025350/bitcoin-libblkmaker.zip
and extract it to the directory where the miner sources are.
then do this:
{
   cd libblkmaker
   make clean
   ./autogen.sh
   make
   sudo make install
   cd ..
}

Then, just run cmake-linux.sh.

wyldfire

newbie

Activity: 23

Merit: 0

Quote from: spirale on September 04, 2013, 01:11:17 AM

Quote from: mtrlt on September 03, 2013, 03:05:13 AM

I got Reaper to compile under Ubuntu Server 13.04. I have to leave for school now though. I'll upload a new version once I get back.

Hey I didn't get my miner. Huh

I posted about my donation in the original topic and also pm.

Don't sweat it, everyone's got it now.

Topic: [XPM] Working on a GPU miner for Primecoin, new thread :) - page 19. (Read 166600 times)