Topic: [*] 8BIT [Dark Masternodes][Anon][Roadmap Stage 4] - page 34. (Read 379550 times)

Best instructions ever.
Just copy & paste.
From my experience if its a vm with not a lot ram or an old machine you should add a swap file (at least 4GB)

I will. This guide will assume you have already built and installed 8bitd for a user on Ubuntu 16.04, and that your blockchain is already synced. If you have not achieved these yet, refer to the guide on pg 263 of this thread.

Start 8bitd:

Allow it some time to once again fully sync. Meanwhile, generate a new bitcoin address under account name "mn"

Send EXACTLY 112 8bit to this address. If you are sending from Cryptopia, you will need to send 113 8bit, as they have a 1 8bit/tx fee.

Now for the masternode setup.
1. Set a static ip for our computer. There are more than enough Ubuntu guides on this out there, so do a search. Remember the local ip chosen for the computer because it will be needed in a moment. You will need to restart networking or simply reboot after changing the  /etc/network/interfaces file for static ip.

2. Make sure the ports you want 8bit to work through are open between the internet and your computer. If you have a router between your machine and the internet you will need to forward the port through your router. You may do this by logging into your router configuration page, by typing your router's local ip address into any web browser connected to the network. For example, I typed "192.168.0.1", some may be "10.0.0.1", etc. (you can run "ifconfig" in terminal to find the "Default Gateway" ip address, same thing). Log in. If you've never logged in before do a search engine search to find the default login credentials specific to your router, mine were username "admin" password "admin", for example. Now that you are in the router config, look for the "Forwarding" or "Port Forwarding" tab/section, and add a new rule to pass the port you choose on to your wallet computer. For the sake of this guide I will choose port 9991. You want to enter your port number into both service port and external port (unless you know what you are doing, I am just simplifying here), and then you want to provide the local ip address of the computer that will be running the masternode. Now open a second port to enable rpc, here I will use port 2222. So you may have forwarded 2 ports of your computer. Make sure to enable these settings in the configuration before exiting. Phewph, that's that.

3. you want to open the actual ports on your Ubuntu machine now, using ufw:
(if you want rpc)

4. Go to whatsmyip.com and get your public ip address if you do not already know it. Write it down.

5. Go back to the terminal and type:
Copy the masternode private key, we'll need it shortly.

6. Now we need to edit the 8bit config file to enable the masternode service:

You want all the following either added or uncommented in your config file:

Change the information specific to your needs (public ip, ports, mnprivkey, etc). Save and exit the editor.

7. Now we're going to stop 8bitd:
Give it a few moments to stop and then start it up again:

If you get an error, you probably just did not give it enough time to close fully before restarting.

Let the wallet sync, check if the 112 8bit has arrived yet, and to see if you are fully synced:

The 112 8bit need 16 confirmations in order to successfully start the masternode, you can check on the block explorer or by using the command:

8. Once the 112 8bit have arrived and are confirmed by at least 16 nodes, only one command remains:


There you go.

You ought to see the following output:
or, oddly, sometimes:

Pat yourself on the back.

8Sq5sDR5mHUEAtsJoJurrjUSu7E3QsCuop

Can someone drop a link to get a 8bit masternode running on Ubuntu? Thanks a lot!

Once I wrote for myself the installation instructions, maybe it will come in handy.

1. Setting dependencies:

2. Installation secp256k1

3. Installing 8bit

Most likely, there will be an error in the assembly.
Therefore, you will need to fix ~/8bit/src/rpcrawtransaction.cpp
search for this line
                     const CScriptID& hash = boost::get(address);
It should work after changed to
                       const CScriptID& hash = boost::get(address);


If everything went well and without errors, then you will have a console version of the wallet.
If you need the GUI:
1. Setting dependencies:

2. Installing 8bit-qt

can anyone please post a tutorial on how to setup masternode on ubuntu ?

I can't download the win Wallet. The Link return an error.

I registered 16bit.party, all the way through to 256bit.party

While I agree, those of us running masternodes will suddenly find ourselves without one.  Perhaps a premine for current MN owners to do a swap, and then burn the rest.

Agree 112 coin is low anyway roadmap looks good, i bought some and will follow this coin