Topic: AMD Rebrand - RX570 / RX580 - Official Thread - page 31. (Read 173441 times)

http://www.overclock.net/t/1604567/polaris-bios-editing-rx5xx-rx4xx
Find performance timings and use Uber Mix 3.1.
The best for Samsung memory. I'm mining XMR and this gave me 850h/s instead of 750h/s also with lower memory clocks only 2100MHz.

The newest one, but I'm mining XMR so it depends... I'm not sure if RX 5xx is working with 16.x versions.

Hello,


it is also possible to set the Voltage offset in the Firmware like on the 470 (HEX Editor)?
someone try it?

lg Martin

After a lot of reading in forums and a thousand unsuccessful bioses I made a bios for Sapphire Pulse RX 580 4GB(Hynix): 30.8-31.3 ETH and 430-410 SC on dual with 120-130W on GPU-Z; Core clock: 1167; Mem Clock: 2150; Driver: 17.5.2. On single is 30.9-31.3 on 80-90W. Stable since 14 hours on two rigs.
Photos: https://[Suspicious link removed]/photos/Zp6jBJhKpCb4so1a72

Has anyone something better for this card?

Does memory errors really affect mining performance? I have 3 Msi 580 Armor 8Gs with Samsung memory that Ive been struggling to push it above 30mh without 2200mhz memory. I have copied 1:1750 straps to 1:2000. Currently doing 1250/2200 and it gives me 30.5mh, even though it is giving me like 10-50k memory errors/min. Power consumption is like 87W from GPUZ and around 140W combining the two values in HWinfo. Is my power consumption good? I can't get it below 0.938v though.

You need to figure out what type of memory you have,  GPUZ, then copy paste certain strings or add a custom string with Polaris bios editor. Your clock looks horrible btw, I don't see anyone going past 2200 (most don't go further than 2100, I see thing happening between 1100/2020 and 1300/2200) and core clock should be reduced not increased. You might have a million memory errors running this clock

19 hash rate out of the box however, that's... strangely low. There might be more going on beyond my pitiful knowledge in these matters

Help! Hey Guys... A bit of a noob here, so greatly appreciate any help.

Setting up my 2nd and 3rd rig and decided to go with the RX580... Ended up with XFX RX580 8GB GTS Black Edition

Info on card:
http://xfxforce.com/en-us/products/amd-radeon-rx-500-series/rx-580-gts-8gb-dd-rx-580p8dbd6

I was only getting 18-19 hash rate out of the box... I can't get it past 20! From what I've read the 580's should be in the high 20's at least.

This was the best I could do... In ethOS I've updated the config...
Core: I've maxed out (according to specs) at 1425.
Memory: 2220

Is there anything else I should try?? Hoping to not have to return 10 GPUs...

Hey guys, what drivers are you using currently? Im getting an MSI Rx 580 soon and I would like to add it to my rig of RX 480/470 with modded bioses, what drivers shall I install? I'm currently on 16.x

Have you applied the patch ?

[/quote]

I've heard from several people now that the uP9505P can't yet be controlled by MSI AB... I wonder if I implemented voltage support for it before MSI did 
[/quote]

Ouch, I read what you wrote on Reddit earlier (I wasn't joking about not sleeping) but didn't quite understand, only the Linux part and I'm running Windows

I guess I have to sit it out then, wait on afterburner or someone else?

I hope the Asus ROG-STRIX-RX580-O8G-GAMING will treat me better. 6 are on the way and I couldn't find many (any) miners write about those, yet all other cards are already sold out over here.

Fingers crossed, on both hands

Turn up your fans to 50% will do the job

Phew... Well here I am. Been messing with my very first rig for a week and a half now, sleeping about 5 hours a night trying to get things going smoothly. And I guess it's about time to stop lurking and ask for help.

Running 4 MSI 580 Gaming X+ (I read the X+ meant it was tested to perform well under lower voltages). Samsung memory.

I've tried about every strap combination thinkable, all were horrible. Except for the custom mod which I placed in :1750 and :2000 (Polariseditor only shows on batch of strings, so I couldn't have placed it wrong).
Finally I was able to hit 30,5 Mh/s with Claymore, dual mining perhaps 27 Mh/s. The precise settings for this... I've regrettably forgotten after countless hours of messing with MSIAfterburner (back to 29,5). Not sure if my nerves can handle more system shutdowns (won't those hurt the cards?)

Power draw however remained horrible in comparison to what I read here. 125 watt (afterburner) is what I draw mining Ether alone. Dual mining Eth/Sia and up up up it goes.

Even when I move the cards all the way -100mV in with afterburner, they simply won't consume less. Trixx I hardly dare touch anymore, using the voltage slider just a bit seems to kill the system immediately.

So my question is, what am I missing? Or does someone have a rom I could use for these cards / Settings they use on the same cards?

Full disclosure
Relive 17.5.2
GA-970A-UD3P (I brought my old computer back to live)
X4 955 Phenom

Thanks in advance!

I forgot... Sapphire Pulse RX 580 4GB

Try to remove old drivers with DDU and then fresh install.

I used this one.

Try this Polaris BIOS Editor

https://github.com/jaschaknack/PolarisBiosEditor/tree/110aa3a5a0aeafe16bb0a96b53583e7e8e77999b

Another problem;

After flashing I see one of my rx580's as Polaris 10. I tried reverting it back to original bios but still the same.

http://imgur.com/a/WE8xX

Also I cannot see the fan of that GPU. Claymore only shows gpu0..Any ideas why that might happen?

PS: I only flashed the card that is identified as Polaris 10

Give us more details about your graphic card.

Thank you. Doing this I was able to save it...

Guys, on my bios higher frequency is 2000. I haven't 2050 or 2100. Is there a way to add it or it isn't necessary?

https://i.imgur.com/qnZLJIR.jpg

First copy strap into notepad and delete white space, there is one white space in HEX string. Maybe that is a problem.

When I do exactly this, I get "Invalid HEX String" from polaris bios editor.After that it crashes but saves the file (0 byte file). Is it the same with you guys too or is it just me ?