Topic: ANN: BITMAIN has Tested Its 28nm Bitcoin Mining Chip BM1382 - page 4. (Read 143995 times)

Quote from: MrTeal on July 31, 2014, 10:23:50 AM

5v at these amperage will not cause shock. You could lay your finger over the entire set of pins without a single problem.

hey bobsag3.
do you have s3 batch3 on hand? i was ordered "Bitmain Antminer S3 *Available July 26th* - 3 Month Colocation / 470Gh/Sec" . but now there is nothing

We do

Excellent

suchmoon

legendary

Activity: 3654

Merit: 8909

https://bpip.org

Here is an alternative for the bitmain switch. It has numerous advantages - insulated, can be bent into any shape required by the application, and much cheaper at 500 MOQ.

http://www.staples.com/Staples-Jumbo-Vinyl-Coated-Paper-Clips-Smooth-500-Tub/product_480109

seftonde

newbie

Activity: 19

Merit: 0

Quote from: Caesium on July 31, 2014, 10:13:49 AM

Quote from: MrTeal on July 31, 2014, 10:03:38 AM

Quote from: hurricandave on July 31, 2014, 09:46:47 AM

Wow! I guess I should be dead now since I licked both of my hands and grabbed the + and - terminals of my 875 Amp 12v car battery, oh wait its DC just like the PSU pins. Kiss

I double dog dare you to lick the two DC wires of a telephone cord. Post to youtube.

I was going to dare him to lick the car battery properly *, none of this "I licked my hands and touched it" crap but I don't want to be responsible for the results Tongue

* notwithstanding you'd need a very long tongue and would actually need to attach wires first.

The car battery really wouldn't be that much worse than a 9V battery. You could try it on a 12V power tool battery or a lantern battery, with the added benefit of not needing to stack three of Gene Simmons' tongues end to end.

You guys remind me of when I was in the navy on a nuclear submarine. One of our jobs was to go into the battery compartment to check on the individual cells where you had to crawl over many batteries that had terminals about 8 inches apart. To prevent shorts there was a rule that you could not go down there with any tool that was over 6 inches long. Of course all of us navy guys claimed to have 'tools' longer than 6 inches..

d

kabopar

hero member

Activity: 616

Merit: 500

All of my PSUs have a built-in power switch, I leave the jumper permanently on the 24 pin connector and use the power supply switch on the rare instances that I need to power the miner on or off. Simply have no use/need for a 'switch board' (certainly not one with the 'shorting feature' of these exposed pins).
Bitmain should focus on the stuff that you are good at - miners. (what about the upgrade kits for S1/S2?)

Cheers

ZiG

sr. member

Activity: 406

Merit: 250

Quote from: philipma1957 on July 31, 2014, 09:10:18 AM

AntMiner Jumper Switch- Bitcoin Miner Accessory

Global Sales start on July 31, will close on August 6th. Shipping starts on August 27th.

PC Power Supply has been widely used to power Bitcoin Miners, but users have to use the paper clip or other metal line to short blue line and black line of the PSU 24 pin interface before powering Bitcoin Miners. It is troublesome thing to short lines, and may lead to unstable power supply.

Here we are glad to introduce a new Bitcoin Miner Accessory - AntMiner Jumper Switch, which is to provide a convenient and effective method to start PSU. Only need to connect it to the PSU 24 pin interface, then press the “Switch”.

Only Available at http://www.bitmaintech.com

I guess I don't understand why there are leads to every pin on the connector, rather than just the ones needed to turn on the PSU. Is it safe to assume those leads would be live, and have current running through them? I'm no EE, I'm just curious if these are 'safe' enough to use in a household with animals or children.

no that could shock as the entire 5v amp's are available. I would not use that product without the pins covered.

I use these

http://www.ebay.com/itm/261302980079?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

added advantage the on off switch has long length for placement.

5v at these amperage will not cause shock. You could lay your finger over the entire set of pins without a single problem.

+1...

But you COULD also lay down on your screwdriver...keys...or other metal / conducting objects "over the entire set of pins with~~out~~ a ~~single~~ a lot of problemS..." ... Grin

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

Quote from: philipma1957 on July 31, 2014, 09:10:18 AM

AntMiner Jumper Switch- Bitcoin Miner Accessory

Global Sales start on July 31, will close on August 6th. Shipping starts on August 27th.

PC Power Supply has been widely used to power Bitcoin Miners, but users have to use the paper clip or other metal line to short blue line and black line of the PSU 24 pin interface before powering Bitcoin Miners. It is troublesome thing to short lines, and may lead to unstable power supply.

Here we are glad to introduce a new Bitcoin Miner Accessory - AntMiner Jumper Switch, which is to provide a convenient and effective method to start PSU. Only need to connect it to the PSU 24 pin interface, then press the “Switch”.

Only Available at http://www.bitmaintech.com

I guess I don't understand why there are leads to every pin on the connector, rather than just the ones needed to turn on the PSU. Is it safe to assume those leads would be live, and have current running through them? I'm no EE, I'm just curious if these are 'safe' enough to use in a household with animals or children.

no that could shock as the entire 5v amp's are available. I would not use that product without the pins covered.

I use these

http://www.ebay.com/itm/261302980079?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

added advantage the on off switch has long length for placement.

5v at these amperage will not cause shock. You could lay your finger over the entire set of pins without a single problem.

okay what do you think will happen if that set of exposed pins presses on the should of the s-3 bitminer. and if you have 10 s-3's with 4 or 5 psu's and 4 or 5 of those psu/shorting devices it can happen. we need mstrongbow to print up a few pretty shields with his 3-d printer. bob you did business with him if you buy 500 of these ask him to 3-d print a shield.

or just tape over the pins.

note not my photo I lifted it from the show us your mining gear thread.

I did not mean shock hazard as much as i meant short / grounding hazard on setups like the one below

those pins on this rack below need to be shielded from contact to the rack.

Xer0

hero member

Activity: 826

Merit: 1000

°^°

AntMiner Jumper Switch- Bitcoin Miner Accessory

Global Sales start on July 31, will close on August 6th. Shipping starts on August 27th.

PC Power Supply has been widely used to power Bitcoin Miners, but users have to use the paper clip or other metal line to short blue line and black line of the PSU 24 pin interface before powering Bitcoin Miners. It is troublesome thing to short lines, and may lead to unstable power supply.

Here we are glad to introduce a new Bitcoin Miner Accessory - AntMiner Jumper Switch, which is to provide a convenient and effective method to start PSU. Only need to connect it to the PSU 24 pin interface, then press the “Switch”.

Only Available at http://www.bitmaintech.com

lol

Quote

It is troublesome thing to short lines, and may lead to unstable power supply.

but that is exactly what your board does, too Tongue

/*
the switch shorts the ps_on pin to ground.
the resistor on the board is just for the led
*/

ducmami

full member

Activity: 121

Merit: 100

Quote from: elduderino on July 29, 2014, 01:25:51 PM

5v at these amperage will not cause shock. You could lay your finger over the entire set of pins without a single problem.

hey bobsag3.
do you have s3 batch3 on hand? i was ordered "Bitmain Antminer S3 *Available July 26th* - 3 Month Colocation / 470Gh/Sec" . but now there is nothing

aztecminer

legendary

Activity: 1092

Merit: 1000

Quote from: aztecminer on July 25, 2014, 11:00:49 AM

Quote from: philipma1957 on July 24, 2014, 02:21:31 PM

Quote from: TravelingMiner on July 24, 2014, 01:21:21 PM

Quote from: philipma1957 on July 21, 2014, 09:51:55 PM

Quote from: TravelingMiner on July 21, 2014, 04:59:01 PM

Has anyone come up with a cheap water cooling solution for the S3? I already have a nice waterloop built that i'd like to use with a 34" radiator outside. Hopefully I don't have to spend an arm+leg on water blocks...

what do you want water cooling for? you can't over clock most of them. the stock fans keep the gear pretty cool.

if you set freq to 212.5 it is cooler and pretty quiet . not whisper quiet but decent.

Not sure what your need for a water block cooler is based on. for all I know you may have a really good reason.

I have an existing waterloop in my server closet and I'm trying to minimize heat inside. I'd also like to see how much OC I could get with water cooling.

okay a good reason. so far it appears the cooling problem is not the chips but the dc to dc regulator.

Maybe of them don't preform well. If you can get it to cool well I would think you will get an oc to freq 250 and 504gh

i will be replacing thermal paste:

http://www.newegg.com/Product/Product.aspx?Item=N82E16835426020

adding heat sinks to regulators:

http://www.amazon.com/Cosmos-Aluminum-Cooling-Heatsinks-cooler/dp/B007XACV8O/ref=lh_ni_t?ie=UTF8&psc=1&smid=ARQJFRRH30M2B

and more psu's:

http://www.newegg.com/Product/Product.aspx?Item=N82E16817139057

Cool list, Aztecminer.

It seems like that would power 2 S3s & still have some room for O/Cing? I looked but couldn't find how many PCI-E connectors it had... It looks like 6 in the photo.

yes it comes with six PCI-E connectors ..
and it will power 2x oc'ed S1's or 2x oc'ed S3's ..

MrTeal

legendary

Activity: 1274

Merit: 1004

Quote from: Caesium on July 31, 2014, 10:13:49 AM

Quote from: MrTeal on July 31, 2014, 10:03:38 AM

Quote from: hurricandave on July 31, 2014, 09:46:47 AM

Wow! I guess I should be dead now since I licked both of my hands and grabbed the + and - terminals of my 875 Amp 12v car battery, oh wait its DC just like the PSU pins. Kiss

I double dog dare you to lick the two DC wires of a telephone cord. Post to youtube.

I was going to dare him to lick the car battery properly *, none of this "I licked my hands and touched it" crap but I don't want to be responsible for the results Tongue

* notwithstanding you'd need a very long tongue and would actually need to attach wires first.

The car battery really wouldn't be that much worse than a 9V battery. You could try it on a 12V power tool battery or a lantern battery, with the added benefit of not needing to stack three of Gene Simmons' tongues end to end.

Caesium

hero member

Activity: 546

Merit: 500

Quote from: MrTeal on July 31, 2014, 10:03:38 AM

Quote from: hurricandave on July 31, 2014, 09:46:47 AM

Wow! I guess I should be dead now since I licked both of my hands and grabbed the + and - terminals of my 875 Amp 12v car battery, oh wait its DC just like the PSU pins. Kiss

I double dog dare you to lick the two DC wires of a telephone cord. Post to youtube.

I was going to dare him to lick the car battery properly *, none of this "I licked my hands and touched it" crap but I don't want to be responsible for the results Tongue

* notwithstanding you'd need a very long tongue and would actually need to attach wires first.

MrTeal

legendary

Activity: 1274

Merit: 1004

Quote from: hurricandave on July 31, 2014, 09:46:47 AM

Quote from: TracerX on July 31, 2014, 09:23:45 AM

Quote from: philipma1957 on July 31, 2014, 09:10:18 AM

Quote from: hurricandave on July 31, 2014, 09:46:47 AM

AntMiner Jumper Switch- Bitcoin Miner Accessory

Global Sales start on July 31, will close on August 6th. Shipping starts on August 27th.

PC Power Supply has been widely used to power Bitcoin Miners, but users have to use the paper clip or other metal line to short blue line and black line of the PSU 24 pin interface before powering Bitcoin Miners. It is troublesome thing to short lines, and may lead to unstable power supply.

Here we are glad to introduce a new Bitcoin Miner Accessory - AntMiner Jumper Switch, which is to provide a convenient and effective method to start PSU. Only need to connect it to the PSU 24 pin interface, then press the “Switch”.

Only Available at http://www.bitmaintech.com

I guess I don't understand why there are leads to every pin on the connector, rather than just the ones needed to turn on the PSU. Is it safe to assume those leads would be live, and have current running through them? I'm no EE, I'm just curious if these are 'safe' enough to use in a household with animals or children.

no that could shock as the entire 5v amp's are available. I would not use that product without the pins covered.

I use these

http://www.ebay.com/itm/261302980079?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

added advantage the on off switch has long length for placement.

5v at these amperage will not cause shock. You could lay your finger over the entire set of pins without a single problem.

But could I lick them? ;-) Thanks for the info, I'll think about ordering a million of them. I presume minersource will be stocking them as well?

Wow! I guess I should be dead now since I licked both of my hands and grabbed the + and - terminals of my 875 Amp 12v car battery, oh wait its DC just like the PSU pins. Kiss

I double dog dare you to lick the two DC wires of a telephone cord. Post to youtube.

Caesium

hero member

Activity: 546

Merit: 500

Wow! I guess I should be dead now since I licked both of my hands and grabbed the + and - terminals of my 875 Amp 12v car battery, oh wait its DC just like the PSU pins. Kiss

Didn't you ever lick a 9v PPA battery as a kid? That's DC and it gives a pretty satisfying buzz

hurricandave

legendary

Activity: 966

Merit: 1003

Quote from: TracerX on July 31, 2014, 09:23:45 AM

Quote from: philipma1957 on July 31, 2014, 09:10:18 AM

AntMiner Jumper Switch- Bitcoin Miner Accessory

Global Sales start on July 31, will close on August 6th. Shipping starts on August 27th.

PC Power Supply has been widely used to power Bitcoin Miners, but users have to use the paper clip or other metal line to short blue line and black line of the PSU 24 pin interface before powering Bitcoin Miners. It is troublesome thing to short lines, and may lead to unstable power supply.

Here we are glad to introduce a new Bitcoin Miner Accessory - AntMiner Jumper Switch, which is to provide a convenient and effective method to start PSU. Only need to connect it to the PSU 24 pin interface, then press the “Switch”.

Only Available at http://www.bitmaintech.com

I guess I don't understand why there are leads to every pin on the connector, rather than just the ones needed to turn on the PSU. Is it safe to assume those leads would be live, and have current running through them? I'm no EE, I'm just curious if these are 'safe' enough to use in a household with animals or children.

no that could shock as the entire 5v amp's are available. I would not use that product without the pins covered.

I use these

http://www.ebay.com/itm/261302980079?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

added advantage the on off switch has long length for placement.

5v at these amperage will not cause shock. You could lay your finger over the entire set of pins without a single problem.

But could I lick them? ;-) Thanks for the info, I'll think about ordering a million of them. I presume minersource will be stocking them as well?

Wow! I guess I should be dead now since I licked both of my hands and grabbed the + and - terminals of my 875 Amp 12v car battery, oh wait its DC just like the PSU pins. Kiss

TracerX

hero member

Activity: 918

Merit: 1002

Quote from: philipma1957 on July 31, 2014, 09:10:18 AM

Quote from: philipma1957 on July 31, 2014, 09:10:18 AM

AntMiner Jumper Switch- Bitcoin Miner Accessory

Global Sales start on July 31, will close on August 6th. Shipping starts on August 27th.

PC Power Supply has been widely used to power Bitcoin Miners, but users have to use the paper clip or other metal line to short blue line and black line of the PSU 24 pin interface before powering Bitcoin Miners. It is troublesome thing to short lines, and may lead to unstable power supply.

Here we are glad to introduce a new Bitcoin Miner Accessory - AntMiner Jumper Switch, which is to provide a convenient and effective method to start PSU. Only need to connect it to the PSU 24 pin interface, then press the “Switch”.

Only Available at http://www.bitmaintech.com

I guess I don't understand why there are leads to every pin on the connector, rather than just the ones needed to turn on the PSU. Is it safe to assume those leads would be live, and have current running through them? I'm no EE, I'm just curious if these are 'safe' enough to use in a household with animals or children.

no that could shock as the entire 5v amp's are available. I would not use that product without the pins covered.

I use these

http://www.ebay.com/itm/261302980079?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

added advantage the on off switch has long length for placement.

5v at these amperage will not cause shock. You could lay your finger over the entire set of pins without a single problem.

But could I lick them? ;-) Thanks for the info, I'll think about ordering a million of them. I presume minersource will be stocking them as well?

bobsag3

hero member

Activity: 546

Merit: 500

Owner, Minersource.net

AntMiner Jumper Switch- Bitcoin Miner Accessory

Global Sales start on July 31, will close on August 6th. Shipping starts on August 27th.

PC Power Supply has been widely used to power Bitcoin Miners, but users have to use the paper clip or other metal line to short blue line and black line of the PSU 24 pin interface before powering Bitcoin Miners. It is troublesome thing to short lines, and may lead to unstable power supply.

Here we are glad to introduce a new Bitcoin Miner Accessory - AntMiner Jumper Switch, which is to provide a convenient and effective method to start PSU. Only need to connect it to the PSU 24 pin interface, then press the “Switch”.

Only Available at http://www.bitmaintech.com

I guess I don't understand why there are leads to every pin on the connector, rather than just the ones needed to turn on the PSU. Is it safe to assume those leads would be live, and have current running through them? I'm no EE, I'm just curious if these are 'safe' enough to use in a household with animals or children.

no that could shock as the entire 5v amp's are available. I would not use that product without the pins covered.

I use these

http://www.ebay.com/itm/261302980079?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

added advantage the on off switch has long length for placement.

5v at these amperage will not cause shock. You could lay your finger over the entire set of pins without a single problem.

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'