[ANN] Spondoolies-Tech - carrier grade, data center ready mining rigs - page 574.

klondike_bar

legendary

Activity: 2128

Merit: 1005

ASIC Wannabe

Quote from: opentoe on June 11, 2014, 09:22:50 PM

Quote from: klondike_bar on June 11, 2014, 06:07:23 PM

WORDS

Then go ahead, put it in a DC. Can't run that at home unless you have a way of not hearing it.

I actually run it in the backroom of a small business - but the other day it became so noisy (seemingly out of the blue that morning) at 70% fans they asked me to shut it down remotely until i could come in later the day and correct the noise issues.

If all goes well the unit will be in a bitcoin colocation by the end of the month with $0.05/kWh power

zvisha

hero member

Activity: 560

Merit: 500

Ok, Con knows of the issue, it will be fixed soon.
For now use previous version for p2p.

Quote from: jonnybravo0311 on June 12, 2014, 02:13:35 AM

Did the 1.4.2 firmware update do something to disable mining on p2pool? I have updated, and now my SP10 will not connect to ANY p2pool node. I can connect to Eligius, BTCGuild, GHash, etc. My local p2pool node? No. Any other p2pool node? No. Before anyone asks... yes, my local node is up. I can confirm this because my 2 S1s are happily hashing away on it. I have also pointed those two to another p2pool node and they hashed there as well.

Thanks for the help.

psahx

full member

Activity: 154

Merit: 100

Quote from: Guy Corem on June 12, 2014, 02:49:53 AM

Kobi's reply:
It’s hard to tell as the mechanical details of the holes and the screws are missing.
It seems to me that the “One Space (1U) Rack Mount Bracket (Ear)MCM Part #: 555-13214 | Penn Elcom Part #: R1206/1U” won’t fit while the “Cisco STK-RACKMOUNT-1RU Rackmount Brackets” seems to fit.
Please verify the screws are #6-32 x 3/8”.
In addition, those mounting brackets are not adjustable so please pay attention to the SP10 depth which is 475mm and the rack rails distance

Thanks a lot. I guess, I will just give it a try with Cisco, does not cost that much. Will let you know.

zvisha

hero member

Activity: 560

Merit: 500

Please write to me and remo, i would like to investigate. Did others here get degradation or hw error increase with some specific version?
My test miners show up to 3% difference between self reported and pool. Do you see more?

Quote from: opentoe on June 11, 2014, 10:42:23 PM

Quote from: klondike_bar on June 11, 2014, 06:07:23 PM

zvisha has been helping me out the last day or so with troubleshooting and getting some temporarily-lost stability back to the miner, however, i am still having some slight issues:

1) fans at 70% used to be fine but as of today sounded terrible. ive soundproofed somewhat and reduced to 60%, but its still a similar volume to what an unmuffled 60% would have sounded like last week. Without a dB meter i could be crazy though - getting this in a DC is top priority. the unit also has very slight vibrations that go away if i put a few pounds of pressure on the middle back edge of the lid.

2) The unit seems to always have a 10% or higher (right now, its about 16%!) error rate, even after hours of operation, temperatures of 26/77C, and most of the chips at 77C with a few at 113C. Miner says 1.41Th while the pool says 1.25-1.3TH. What is the accepted/error ratio for others?

the product is excellent, but it needs to be operated in a datacenter or somewhere that the fans running at 90-100% wont burst eardrums. I would really love to see the SP10 fit in an SP30 case to better dissipate the heat and use bigger/quieter fans. Most DC racks cant handle anywhere near the 40-50kW draw that the SP10 and SP30 models enable

I was also always getting 1.3TH consistently, then put the new firmware on. Now I'm down to 1.2TH. So I'm going the other way. I'm still on a 110V circuit and get switched over to a 208V soon so hopefully I'll see the nice 1.45TH that I see in all the Spondoolie video's.

Guy Corem

donator

Activity: 1414

Merit: 1051

Spondoolies, Beam & DAGlabs

Quote from: psahx on June 11, 2014, 02:30:30 PM

Quote from: FAQ - rack installation guidelines.docxfrom Guy Corem (Spondoolies-Tech)

The height of the Miner is 1.25U but standard 1U rack mount ears may fit

Can we use these or these?

Kobi's reply:
It’s hard to tell as the mechanical details of the holes and the screws are missing.
It seems to me that the “One Space (1U) Rack Mount Bracket (Ear)MCM Part #: 555-13214 | Penn Elcom Part #: R1206/1U” won’t fit while the “Cisco STK-RACKMOUNT-1RU Rackmount Brackets” seems to fit.
Please verify the screws are #6-32 x 3/8”.
In addition, those mounting brackets are not adjustable so please pay attention to the SP10 depth which is 475mm and the rack rails distance

jonnybravo0311

legendary

Activity: 1344

Merit: 1024

Mine at Jonny's Pool

Did the 1.4.2 firmware update do something to disable mining on p2pool? I have updated, and now my SP10 will not connect to ANY p2pool node. I can connect to Eligius, BTCGuild, GHash, etc. My local p2pool node? No. Any other p2pool node? No. Before anyone asks... yes, my local node is up. I can confirm this because my 2 S1s are happily hashing away on it. I have also pointed those two to another p2pool node and they hashed there as well.

Thanks for the help.

raskul

sr. member

Activity: 434

Merit: 250

Quote from: Guy Corem on June 12, 2014, 02:09:03 AM

Quote from: raskul on June 12, 2014, 01:37:32 AM

can we have a status update on June batch please? thanks

Small number of shipping will be today.
More on Monday and Wednesday or Thursday next week.

thanks for the update, appreciated.

Guy Corem

donator

Activity: 1414

Merit: 1051

Spondoolies, Beam & DAGlabs

Quote from: raskul on June 12, 2014, 01:37:32 AM

can we have a status update on June batch please? thanks

Small number of shipping will be today.
More on Monday and Wednesday or Thursday next week.

raskul

sr. member

Activity: 434

Merit: 250

Quote from: Biodom on June 12, 2014, 01:41:25 AM

Quote from: raskul on June 12, 2014, 01:37:32 AM

can we have a status update on June batch please? thanks

Didn't you hear the news, they sold all remaining Sp-10 to Taras [LNU].

Biodom, I have an order for 2 SP10 from June batch, i guess you were just too late. that's how it is mucker Cheesy

a s-t-a-t-u-s update - you perceive this to mean something other than a s-t-a-t-u-s update.

Don't act so butt-hurt about it.

Biodom

legendary

Activity: 3892

Merit: 4331

Quote from: raskul on June 12, 2014, 01:37:32 AM

can we have a status update on June batch please? thanks

Didn't you hear the news, they sold all remaining Sp-10 to Taras [LNU].

raskul

sr. member

Activity: 434

Merit: 250

can we have a status update on June batch please? thanks

opentoe

legendary

Activity: 1274

Merit: 1000

Personal text my ass....

Quote from: klondike_bar on June 11, 2014, 06:07:23 PM

zvisha has been helping me out the last day or so with troubleshooting and getting some temporarily-lost stability back to the miner, however, i am still having some slight issues:

1) fans at 70% used to be fine but as of today sounded terrible. ive soundproofed somewhat and reduced to 60%, but its still a similar volume to what an unmuffled 60% would have sounded like last week. Without a dB meter i could be crazy though - getting this in a DC is top priority. the unit also has very slight vibrations that go away if i put a few pounds of pressure on the middle back edge of the lid.

2) The unit seems to always have a 10% or higher (right now, its about 16%!) error rate, even after hours of operation, temperatures of 26/77C, and most of the chips at 77C with a few at 113C. Miner says 1.41Th while the pool says 1.25-1.3TH. What is the accepted/error ratio for others?

the product is excellent, but it needs to be operated in a datacenter or somewhere that the fans running at 90-100% wont burst eardrums. I would really love to see the SP10 fit in an SP30 case to better dissipate the heat and use bigger/quieter fans. Most DC racks cant handle anywhere near the 40-50kW draw that the SP10 and SP30 models enable

I was also always getting 1.3TH consistently, then put the new firmware on. Now I'm down to 1.2TH. So I'm going the other way. I'm still on a 110V circuit and get switched over to a 208V soon so hopefully I'll see the nice 1.45TH that I see in all the Spondoolie video's.

opentoe

legendary

Activity: 1274

Merit: 1000

Personal text my ass....

Quote from: RoadStress on June 11, 2014, 09:49:39 PM

Quote from: opentoe on June 11, 2014, 09:22:50 PM

Then go ahead, put it in a DC. Can't run that at home unless you have a way of not hearing it.

https://bitcointalksearch.org/topic/hw-hosting-directory-reputation-622998 Need more reviews here!

What are the redline highs that should be at TEMP FRONT and TEMP BACK?

RoadStress

legendary

Activity: 1904

Merit: 1007

Quote from: opentoe on June 11, 2014, 09:22:50 PM

Then go ahead, put it in a DC. Can't run that at home unless you have a way of not hearing it.

https://bitcointalksearch.org/topic/hw-hosting-directory-reputation-622998 Need more reviews here!

opentoe

legendary

Activity: 1274

Merit: 1000

Personal text my ass....

Quote from: klondike_bar on June 11, 2014, 06:07:23 PM

zvisha has been helping me out the last day or so with troubleshooting and getting some temporarily-lost stability back to the miner, however, i am still having some slight issues:

1) fans at 70% used to be fine but as of today sounded terrible. ive soundproofed somewhat and reduced to 60%, but its still a similar volume to what an unmuffled 60% would have sounded like last week. Without a dB meter i could be crazy though - getting this in a DC is top priority. the unit also has very slight vibrations that go away if i put a few pounds of pressure on the middle back edge of the lid.

2) The unit seems to always have a 10% or higher (right now, its about 16%!) error rate, even after hours of operation, temperatures of 26/77C, and most of the chips at 77C with a few at 113C. Miner says 1.41Th while the pool says 1.25-1.3TH. What is the accepted/error ratio for others?

the product is excellent, but it needs to be operated in a datacenter or somewhere that the fans running at 90-100% wont burst eardrums. I would really love to see the SP10 fit in an SP30 case to better dissipate the heat and use bigger/quieter fans. Most DC racks cant handle anywhere near the 40-50kW draw that the SP10 and SP30 models enable

Then go ahead, put it in a DC. Can't run that at home unless you have a way of not hearing it.

klondike_bar

legendary

Activity: 2128

Merit: 1005

ASIC Wannabe

zvisha has been helping me out the last day or so with troubleshooting and getting some temporarily-lost stability back to the miner, however, i am still having some slight issues:

1) fans at 70% used to be fine but as of today sounded terrible. ive soundproofed somewhat and reduced to 60%, but its still a similar volume to what an unmuffled 60% would have sounded like last week. Without a dB meter i could be crazy though - getting this in a DC is top priority. the unit also has very slight vibrations that go away if i put a few pounds of pressure on the middle back edge of the lid.

2) The unit seems to always have a 10% or higher (right now, its about 16%!) error rate, even after hours of operation, temperatures of 26/77C, and most of the chips at 77C with a few at 113C. Miner says 1.41Th while the pool says 1.25-1.3TH. What is the accepted/error ratio for others?

the product is excellent, but it needs to be operated in a datacenter or somewhere that the fans running at 90-100% wont burst eardrums. I would really love to see the SP10 fit in an SP30 case to better dissipate the heat and use bigger/quieter fans. Most DC racks cant handle anywhere near the 40-50kW draw that the SP10 and SP30 models enable

blaiser

member

Activity: 99

Merit: 10

Quote from: DevonMiner on June 11, 2014, 05:11:20 PM

+10 for Sponds:

OK ... so I have x2 SP10s ... and one was behaving below spec ... I have to say, the support from Spondoolies was exemplary.

Remo and Zvisha reacted VERY quickly to emails, gave good advice and online support ... and now my below average SP10 has become the quickest of the two!

Never before have I seen such dedication to a product, and dedication to the customer before in the BTC world.

Rock!

... Just wish I'd ordered some more SP30s in the GB ... OH WELL!

+1 - Hats off to Guy and his hand picked crew without question.

DevonMiner

sr. member

Activity: 471

Merit: 250

+10 for Sponds:

OK ... so I have x2 SP10s ... and one was behaving below spec ... I have to say, the support from Spondoolies was exemplary.

Remo and Zvisha reacted VERY quickly to emails, gave good advice and online support ... and now my below average SP10 has become the quickest of the two!

Never before have I seen such dedication to a product, and dedication to the customer before in the BTC world.

Rock!

... Just wish I'd ordered some more SP30s in the GB ... OH WELL!

psahx

full member

Activity: 154

Merit: 100

Quote from: FAQ - rack installation guidelines.docxfrom Guy Corem (Spondoolies-Tech)

The height of the Miner is 1.25U but standard 1U rack mount ears may fit

Can we use these or these?

jimmothy

hero member

Activity: 770

Merit: 509

I don't think anyone here has a magic crystal ball accurate enough to predict the btc/usd rate and btc difficulty in 3 months, let alone 3 months after that.

Topic: [ANN] Spondoolies-Tech - carrier grade, data center ready mining rigs - page 574. (Read 1260354 times)