I have a gtx1080, and the mutlipoolmner never seems to finish 'benchmarking' , i see red error text show up in the powershell in between algos, but can't make it out. how long should it take? i havent gotten to the part where I can actaully mine yet
Topic: [ANN][POOL] Mining Pool Hub - Multipool. Multialgo, Auto Exchange to any coin. - page 252. (Read 487870 times)
May 01, 2017, 05:44:31 PM
Check the logs in the log folder. All powershell outputs are sent there so you can see what the error is that's repeating.
May 01, 2017, 02:56:34 PM
I have a gtx1080, and the mutlipoolmner never seems to finish 'benchmarking' , i see red error text show up in the powershell in between algos, but can't make it out. how long should it take? i havent gotten to the part where I can actaully mine yet
if it takes more than 10min something is wrong May 01, 2017, 09:40:52 AM
I have a gtx1080, and the mutlipoolmner never seems to finish 'benchmarking' , i see red error text show up in the powershell in between algos, but can't make it out. how long should it take? i havent gotten to the part where I can actaully mine yet
May 01, 2017, 05:38:19 AM
I really like the automatic coin switching, I mine Ethash and use to manually switch to the various pools depending on the stats from whattomine.com prior to Mining Pool Hub.
I'm curious how is the normalized profits determine? Often whattomine.com's most profitable coin is different then the ethash coin being mined on Mining Pool Hub. I've often wonder if whattomine.com lags even when using the current profit and current difficulty setting.
In the image below both taken at the same time, whattomine say's MUSIC while MPH is mining EXP.
I'm curious how is the normalized profits determine? Often whattomine.com's most profitable coin is different then the ethash coin being mined on Mining Pool Hub. I've often wonder if whattomine.com lags even when using the current profit and current difficulty setting.
In the image below both taken at the same time, whattomine say's MUSIC while MPH is mining EXP.
April 30, 2017, 11:35:38 PM
If I look at dashboard for ethereum it goes here
Round Shares [Submitted shares since last found block (ie. round shares)]
Est. Shares 18,089,206 (done: 0%)
Your Valid 0.0000
Your Invalid 0.0000 (0.00%)
My valid and my invalid are always 0.
Also aaron, how do you mine your devfee?
The reason I ask is will you have to disconnect from current pool and mine and then disconnect again from miningpoolhub and then continue?
Or does claymore allow temporary change of username?
Also I got email from miningpoolhub that my rig is off. Great idea. I think I turned on something called monitor. I want to do it again. How do I? I forget.
Round Shares [Submitted shares since last found block (ie. round shares)]
Est. Shares 18,089,206 (done: 0%)
Your Valid 0.0000
Your Invalid 0.0000 (0.00%)
My valid and my invalid are always 0.
Also aaron, how do you mine your devfee?
The reason I ask is will you have to disconnect from current pool and mine and then disconnect again from miningpoolhub and then continue?
Or does claymore allow temporary change of username?
Also I got email from miningpoolhub that my rig is off. Great idea. I think I turned on something called monitor. I want to do it again. How do I? I forget.
Mostly, valid should be not zero if you are mining correctly. You hashrate is also zero?
I don't know much about multipoolminer, so I can't answer about multipoolminer.
You can turn on/off at each pool's worker page. not hub worker's page.
Really wished I did not have to hunt on which pool/coin my workers are active. You need a centralised page showing miner activity with monitoring. not on a coin level as it will send an email every time the rig is switched.
+1 Been wanting that also, a dashboard that shows all in one, also more transparency on what is happening would be great.
Ive mined a couple times now and wanted to auto swap to monero, its seems like both times got nothing. Ever since the the 2.5 multipool miner came out and the MPH went awol things have been goofy.
I have 2000 skein sitting, 70 feathercoin, 13 music coin all sitting where i cant do anything with .
On another note, it would be great if you could check keep or hold coins that you happen to mine but dont want to auto trade. It seems like a UI that has a toggle to automine wouldnt be to hard IF true, just send to credited, if false send to credited for auto.
Being a novice miner of less than a year doesnt help me at all, the constant renaming and reconfiguring files is frustrating enough! It never ends, and so much to learn on my own to improve things and of course always new coins and stress of chasing the dollar.
I will say though I feel you are giving us the best you can, and you are doing the best you can and also have struggles that are real!
What if we had our own forum where users could discuss tips and tricks to making this work. Its a large enough project where it feels like it gets bottlenecked here.
April 30, 2017, 03:55:30 PM
If I look at dashboard for ethereum it goes here
Round Shares [Submitted shares since last found block (ie. round shares)]
Est. Shares 18,089,206 (done: 0%)
Your Valid 0.0000
Your Invalid 0.0000 (0.00%)
My valid and my invalid are always 0.
Also aaron, how do you mine your devfee?
The reason I ask is will you have to disconnect from current pool and mine and then disconnect again from miningpoolhub and then continue?
Or does claymore allow temporary change of username?
Also I got email from miningpoolhub that my rig is off. Great idea. I think I turned on something called monitor. I want to do it again. How do I? I forget.
Round Shares [Submitted shares since last found block (ie. round shares)]
Est. Shares 18,089,206 (done: 0%)
Your Valid 0.0000
Your Invalid 0.0000 (0.00%)
My valid and my invalid are always 0.
Also aaron, how do you mine your devfee?
The reason I ask is will you have to disconnect from current pool and mine and then disconnect again from miningpoolhub and then continue?
Or does claymore allow temporary change of username?
Also I got email from miningpoolhub that my rig is off. Great idea. I think I turned on something called monitor. I want to do it again. How do I? I forget.
Mostly, valid should be not zero if you are mining correctly. You hashrate is also zero?
I don't know much about multipoolminer, so I can't answer about multipoolminer.
You can turn on/off at each pool's worker page. not hub worker's page.
Really wished I did not have to hunt on which pool/coin my workers are active. You need a centralised page showing miner activity with monitoring. not on a coin level as it will send an email every time the rig is switched.
April 30, 2017, 02:23:17 PM
Hi I need some help
Got one rig with 2 Nvidia and Pro Duo(2x Furyx) Running windows 7 64bit and AMD driver 16.3.2
get the following error when i try to benchmark with sgminer for skein
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen -k ethash -o stratum+ssl://europe.ethash-hub.miningpoolhub.com:1 7020 -u Etherion.asabata -p x --gpu-threads 1 --worksize 192 --xintensity 1024
What can be the problem?
And now this
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen-k equihash -o stratum+ssl://europe.equihash-hub.miningpoolhub.com:17023 -u Etherion.asabata -px --gpu-threads 2 --worksize 256
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen -k skeincoin -o stratum+ssl://hub.miningpoolhub.com:17016 -u Etherion.asabata -p x --gpu-threads 2 --worksize 64
sgminer clearly don't run out the box with windows 7
Got one rig with 2 Nvidia and Pro Duo(2x Furyx) Running windows 7 64bit and AMD driver 16.3.2
get the following error when i try to benchmark with sgminer for skein
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen -k ethash -o stratum+ssl://europe.ethash-hub.miningpoolhub.com:1 7020 -u Etherion.asabata -p x --gpu-threads 1 --worksize 192 --xintensity 1024
What can be the problem?
And now this
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen-k equihash -o stratum+ssl://europe.equihash-hub.miningpoolhub.com:17023 -u Etherion.asabata -px --gpu-threads 2 --worksize 256
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen -k skeincoin -o stratum+ssl://hub.miningpoolhub.com:17016 -u Etherion.asabata -p x --gpu-threads 2 --worksize 64
sgminer clearly don't run out the box with windows 7
I think you'd better check AMD driver settings and contact to genesis mining dev.
Here's some skein miner from miningpoolhub.
https://github.com/miningpoolhub/all-in-one-miner/releases
It's a bit out-dated, but will work for skein algo well.
Thank you. I will try that. I have contacted the dev on sgminer 5.5.5-gm. No luck yet.
Another problem is nsgminer. I tried https://github.com/ghostlander/nsgminer
Any suggestion which miner would work on windows 10, AMD RX 480 system?
I can't get nsgminer.exe to work. Just shows a blank screen with blinking terminal cursor.
nsgminer.exe --api-listen -k neoscrypt -o stratum+tcp://hub.miningpoolhub.com:17012 -u Etherion.ws10 -p x --gpu-threads 1 --worksize 64 --intensity 13 --thread-concurrency 64
I also tried stratum+ssl: but the dev said the miner does not support openssl.
Any suggestions which miner can work for NeoScrypt?
April 30, 2017, 12:45:14 PM
any plans tonadd insane when it goes to pow? gear up and coming x11 coin
April 30, 2017, 12:41:14 PM
when do you add Ubiq 
since musicoin is added so fast i hope this one finaly get added too
and i hate it to mine on a other site just for one coin
since musicoin is added so fast i hope this one finaly get added tooand i hate it to mine on a other site just for one coin
I'm watching their profitability for days. I'll prepare when their profitability is stable and high.
I actually like coins with unstable profitability.
Anyway, how do I monitor miner?
Coinontrop has PPS version. I wonder when you will have that.
April 30, 2017, 08:33:27 AM
This problem is only happening with ccminer and already known issue.
Can you please try with
--diff-multiplier 0.5
or
--diff-multiplier 2
option and tell me the result?
I don't have nvidia gpu to test currently and can't test now.
I don't have such problem, for example, on suprnova with same miner. I've used "D=xx" parameter to set constant stratum difficulty and after that on suprnova I've got correct share rate and suprnova's dashboard show my real hashrate ~1.1MH/s. But on miningpoolhub even with this parameter stratum difficulty jumps all time and shows worst share rate and hashboard shows 0.3-0.6 MH/s resultsCan you please try with
--diff-multiplier 0.5
or
--diff-multiplier 2
option and tell me the result?
I don't have nvidia gpu to test currently and can't test now.
So, seems that this problem caused by pool.
Why your pool gives so worst share rate?? even suprnova with FEW TIMES lower hashrate 367 MH/s vs 14998 MH/s can distribute correct share rate, but your pool - not
Please fix this problem. Other pools don't have such issue
-f, --diff-factor 0.5
http://imgur.com/l0oQN8G
-f, --diff-factor 1.5
http://imgur.com/3KIjprO
April 29, 2017, 09:33:39 AM
Hi, All.
Who mine xzc on minigpoolhub with ccminer on nVidia cards? Need your healp
I have some problems with this pool: stratum difficulty is changes too often and due to this my share rate is about half of the amount that should be (2-5 shres per minute, while on suprniova same hardware pulls average 7 shares per minute).
In the end: earnings in xzc about 15% less then should (calculating average difficulty and hashrate).
BTW on suprnova pool the same hardware gives about double shares to pool. but I don't like to mine xzc on suprnova due to very low pool's hashrate
Who mine xzc on minigpoolhub with ccminer on nVidia cards? Need your healp
I have some problems with this pool: stratum difficulty is changes too often and due to this my share rate is about half of the amount that should be (2-5 shres per minute, while on suprniova same hardware pulls average 7 shares per minute).
In the end: earnings in xzc about 15% less then should (calculating average difficulty and hashrate).
BTW on suprnova pool the same hardware gives about double shares to pool. but I don't like to mine xzc on suprnova due to very low pool's hashrate
This problem is only happening with ccminer and already known issue.
Can you please try with
--diff-multiplier 0.5
or
--diff-multiplier 2
option and tell me the result?
I don't have nvidia gpu to test currently and can't test now.
April 29, 2017, 09:32:01 AM
when do you add Ubiq since musicoin is added so fast i hope this one finaly get added too
and i hate it to mine on a other site just for one coin
since musicoin is added so fast i hope this one finaly get added tooand i hate it to mine on a other site just for one coin
I'm watching their profitability for days. I'll prepare when their profitability is stable and high.
April 29, 2017, 09:27:15 AM
How do I get an email if things went wrong in miningpoolhub
I am pretty sure it's in this URL
https://miningpoolhub.com/?page=account&action=hubworkers
But I no longer see a checkbox saying monitor there.
I am pretty sure it's in this URL
https://miningpoolhub.com/?page=account&action=hubworkers
But I no longer see a checkbox saying monitor there.
Each pool's worker page has monitor button.
https://ethereum.miningpoolhub.com/index.php?page=account&action=workers
April 29, 2017, 09:26:32 AM
Any plans on adding Ubiq to the eth multi-algo?
Ends up on top of whattomine every now and then.
Ends up on top of whattomine every now and then.
I've been watching Ubiq coin these days.
Not sure at this moment. Their profitability goes up and down too frequently because of low hashrate. If miningpoolhub add that to auto switch, their profitability will drop rapidly.
April 29, 2017, 09:22:18 AM
Decred and supported?
How can i test double mining of eth + decred?
Which parameters should I use?
I can manually change your username.
Please pm me your id, username, new username.
I already sent you the exchange data
How can i test double mining of eth + decred?
Which parameters should I use?
Is it possible to change the username?
I can manually change your username.
Please pm me your id, username, new username.
I already sent you the exchange data
Here's commandline example to mine ethereum and Siacoin concurrently
EthDcrMiner64.exe -epool us-east.ethash-hub.miningpoolhub.com:20535 -ewal username.workername -eworker username.workername -esm 2 -epsw x -allpools 1 -dpool stratum+tcp://hub.miningpoolhub.com:20550 -dwal username.workername -dpsw x -dcoin sc
I think you can tweak some option parts from above commandline to mine DCR.
I replied PM about username change
April 29, 2017, 09:05:17 AM
Hi I need some help
Got one rig with 2 Nvidia and Pro Duo(2x Furyx) Running windows 7 64bit and AMD driver 16.3.2
get the following error when i try to benchmark with sgminer for skein
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen -k ethash -o stratum+ssl://europe.ethash-hub.miningpoolhub.com:1 7020 -u Etherion.asabata -p x --gpu-threads 1 --worksize 192 --xintensity 1024
What can be the problem?
And now this
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen-k equihash -o stratum+ssl://europe.equihash-hub.miningpoolhub.com:17023 -u Etherion.asabata -px --gpu-threads 2 --worksize 256
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen -k skeincoin -o stratum+ssl://hub.miningpoolhub.com:17016 -u Etherion.asabata -p x --gpu-threads 2 --worksize 64
sgminer clearly don't run out the box with windows 7
Got one rig with 2 Nvidia and Pro Duo(2x Furyx) Running windows 7 64bit and AMD driver 16.3.2
get the following error when i try to benchmark with sgminer for skein
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen -k ethash -o stratum+ssl://europe.ethash-hub.miningpoolhub.com:1 7020 -u Etherion.asabata -p x --gpu-threads 1 --worksize 192 --xintensity 1024
What can be the problem?
And now this
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen-k equihash -o stratum+ssl://europe.equihash-hub.miningpoolhub.com:17023 -u Etherion.asabata -px --gpu-threads 2 --worksize 256
Bin\AMD-GenesisMining\sgminer.exe --gpu-platform 1 --api-listen -k skeincoin -o stratum+ssl://hub.miningpoolhub.com:17016 -u Etherion.asabata -p x --gpu-threads 2 --worksize 64
sgminer clearly don't run out the box with windows 7
I think you'd better check AMD driver settings and contact to genesis mining dev.
Here's some skein miner from miningpoolhub.
https://github.com/miningpoolhub/all-in-one-miner/releases
It's a bit out-dated, but will work for skein algo well.
April 29, 2017, 09:02:02 AM
Hello, please help me.
I registered on site. Use Claymore CryptoNote CPU Miner v3.5
set bat file like:
NsCpuCNMiner64.exe -o stratum+tcp://europe.monero.miningpoolhub.com:20580 -u LOGIN.worker1 -p x -t 4
where LOGIN is my login on site =)
I have an error
Error in server response
: {"id":1,"jsonrpc":"2.0","error":{"code":-1,"message":"invalidusernameusedforlogin"}}
At same time, the worker appeared on the list of workers..
I registered on site. Use Claymore CryptoNote CPU Miner v3.5
set bat file like:
NsCpuCNMiner64.exe -o stratum+tcp://europe.monero.miningpoolhub.com:20580 -u LOGIN.worker1 -p x -t 4
where LOGIN is my login on site =)
I have an error
Error in server response
: {"id":1,"jsonrpc":"2.0","error":{"code":-1,"message":"invalidusernameusedforlogin"}}
At same time, the worker appeared on the list of workers..
Ah... I think claymore doesn't support account based mining yet. Wallet based mining does not work well because of devfee gathering.
I'll contact him. Maybe you can ask him to add account based mining too.
April 29, 2017, 08:58:37 AM
Please help me how to autoswitch between myriad-groestl,skein and neoscrypt with my rig? I am new and need your help. Which miner is more convenient to use for Miningpoolhub pool? Thanks in advance! 
Try MultiPoolMiner: https://github.com/aaronsace/MultiPoolMiner/releases
Enter the algorithms in the 'start.bat'.
So i edit your start file and included those algo.
Any idea when you will be able to add Decred(DCR)? Does it have to mine to MPH? I have hacked my claymore script for eth to dual mine but obvosly it is not taken into count when comparing.
I can't guarantee the date for DCR pool currently. Most works are delayed than expected.
I think you can change claymore script to mine DCR from other pools. I have no idea about multipoolminer, so I can't advice in detail.
April 29, 2017, 08:55:59 AM
If I look at dashboard for ethereum it goes here
Round Shares [Submitted shares since last found block (ie. round shares)]
Est. Shares 18,089,206 (done: 0%)
Your Valid 0.0000
Your Invalid 0.0000 (0.00%)
My valid and my invalid are always 0.
Also aaron, how do you mine your devfee?
The reason I ask is will you have to disconnect from current pool and mine and then disconnect again from miningpoolhub and then continue?
Or does claymore allow temporary change of username?
Also I got email from miningpoolhub that my rig is off. Great idea. I think I turned on something called monitor. I want to do it again. How do I? I forget.
Round Shares [Submitted shares since last found block (ie. round shares)]
Est. Shares 18,089,206 (done: 0%)
Your Valid 0.0000
Your Invalid 0.0000 (0.00%)
My valid and my invalid are always 0.
Also aaron, how do you mine your devfee?
The reason I ask is will you have to disconnect from current pool and mine and then disconnect again from miningpoolhub and then continue?
Or does claymore allow temporary change of username?
Also I got email from miningpoolhub that my rig is off. Great idea. I think I turned on something called monitor. I want to do it again. How do I? I forget.
Mostly, valid should be not zero if you are mining correctly. You hashrate is also zero?
I don't know much about multipoolminer, so I can't answer about multipoolminer.
You can turn on/off at each pool's worker page. not hub worker's page.
April 29, 2017, 08:53:15 AM
Hi I am using MultiPoolMiner and it seems to select the correct algo for the most prof coin. It is using port 17xxx
Is this right? I see on MPH home page that it should be using port 12xxx for Mult-alog switching.
So I am confused now. so 17xxx + MPM = 12XXX?
Is this right? I see on MPH home page that it should be using port 12xxx for Mult-alog switching.
So I am confused now. so 17xxx + MPM = 12XXX?
12xxx is used when you use pool based switching. Pool calculates and disconnects, open port for specific miners.
Multipoolminer is client based switching which connect and disconnect by their own calculation.
Multipoolminer is working correctly AFAIK.
Thank you.
Can one dual mine other coins aswell? I see eth+sia is possible. How about the others? I see there is a pool for lbry but not sure if it will work. how about the others Pascal and Decred. I don't see pools for them on MPH
Other dual mining coins are not provided yet. I'll open them one by one.
Sorry for late.
Jump to: