ANTMINER C1 Discussion and Support Thread - page 3.

pinhead666

sr. member

Activity: 265

Merit: 250

Quote from: notlist3d on October 15, 2015, 09:59:02 AM

Quote from: dunand on October 15, 2015, 07:47:44 AM

I have a C1 that is broken. I cannot ssh it and the fan is always running full speed. I want to try to reflash the sd card. Does anyone have an image I can use ?

Edit: I will try the image from the Dogie support page https://bitcointalksearch.org/topic/m.9389747

It sounds like it is mining i fans running at full speed. Have you looked at pool during the times it does this?

And dogies image should do the trick if it's software. That is the nice thing about SD card using miners as they are easy to reset to factory.

Or if the fans run at full speed as soon as power is connected,then controller is not powered at all or is completely dead.

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: dunand on October 15, 2015, 07:47:44 AM

I have a C1 that is broken. I cannot ssh it and the fan is always running full speed. I want to try to reflash the sd card. Does anyone have an image I can use ?

Edit: I will try the image from the Dogie support page https://bitcointalksearch.org/topic/m.9389747

It sounds like it is mining i fans running at full speed. Have you looked at pool during the times it does this?

And dogies image should do the trick if it's software. That is the nice thing about SD card using miners as they are easy to reset to factory.

dunand

hero member

Activity: 637

Merit: 502

I have a C1 that is broken. I cannot ssh it and the fan is always running full speed. I want to try to reflash the sd card. Does anyone have an image I can use ?

Edit: I will try the image from the Dogie support page https://bitcointalksearch.org/topic/m.9389747

Didldak

full member

Activity: 150

Merit: 100

Oh boy!

Anyway, I regred so much that I didnt install floor heating tubes in my "main" room. It would be so cool run warm coolant from C1 thru them

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: Tupsu on October 12, 2015, 05:31:02 PM

Quote from: notlist3d on October 12, 2015, 02:42:12 PM

Quote from: Didldak on October 12, 2015, 10:58:16 AM

Agreed to new water cooled miner, I use C1 for heating during winter. I did last winter without any additional heat source and it was perfect. Just give us S7 with few waterblocks on it, we will take care of the rest

It will take someone to mod most likely. I just don't see another C series for the many reasons I have posted earlier.

You can look at their partner syscooling on C1, and S5 mod. They have not logged in for months. So that does not sound very promising.

Apparently, this forum was for them too stressful.

I still have 3 x C1 working pump for 8 (Two of them were replacements pumps)
that working with S5 and C1 cooling radiators .

But Syscooling answer e-mails and still sells an their website.
A few days ago, I bought a third cooling kit for 2x S5
http://shop.syscooling.com/goods.php?id=46

If you had a RMA email was "stressful" to. I still remember a RMA pump in the mail for a month on one and over a month on my second pump, both died within 2 days.

They were a huge pain on batch one after they dry tested water pumps and shipped them out. And that horrible V1 fan harness. I had a horrible time with them. It is back who know how many pages. But I did not feel sad when them and bitmain split as far as joint ventures.

If Bitmain does do a water cooling again (which I dount). I hope they keep it in house they could have beat syscooling but that is not saying much. And I realize not all had as bad as I did.

Tupsu

legendary

Activity: 1218

Merit: 1003

Quote from: notlist3d on October 12, 2015, 02:42:12 PM

Quote from: Didldak on October 12, 2015, 10:58:16 AM

Agreed to new water cooled miner, I use C1 for heating during winter. I did last winter without any additional heat source and it was perfect. Just give us S7 with few waterblocks on it, we will take care of the rest

It will take someone to mod most likely. I just don't see another C series for the many reasons I have posted earlier.

You can look at their partner syscooling on C1, and S5 mod. They have not logged in for months. So that does not sound very promising.

Apparently, this forum was for them too stressful.

I still have 3 x C1 working pump for 8 (Two of them were replacements pumps)
that working with S5 and C1 cooling radiators .

But Syscooling answer e-mails and still sells an their website.
A few days ago, I bought a third cooling kit for 2x S5
http://shop.syscooling.com/goods.php?id=46

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: Didldak on October 12, 2015, 10:58:16 AM

Agreed to new water cooled miner, I use C1 for heating during winter. I did last winter without any additional heat source and it was perfect. Just give us S7 with few waterblocks on it, we will take care of the rest

It will take someone to mod most likely. I just don't see another C series for the many reasons I have posted earlier.

You can look at their partner syscooling on C1, and S5 mod. They have not logged in for months. So that does not sound very promising.

Didldak

full member

Activity: 150

Merit: 100

Oh boy!

Agreed to new water cooled miner, I use C1 for heating during winter. I did last winter without any additional heat source and it was perfect. Just give us S7 with few waterblocks on it, we will take care of the rest

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: dunand on October 09, 2015, 10:30:25 AM

We need another watercooled miner. The C1 is so quiet and stable. 69 days uptime and temperature super low.

I don't see them going into another watercooling machine. I think they enjoy it being much simpler with air from fans. That sucks for those fans of wattercooling.

But I predict mods of new gear is only water cooling we will see with BM gear. And another part is it's easy to put in thier farms for burn in on fan unit's. Water cooling is going to take them more time and have to worry about liquid.

dunand

hero member

Activity: 637

Merit: 502

We need another watercooled miner. The C1 is so quiet and stable. 69 days uptime and temperature super low.

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: uralcryptocoin on September 28, 2015, 04:13:42 AM

Quote from: Didldak on September 24, 2015, 10:32:46 AM

Hello guys,

my syscooling pump has been offline for few months and after I turned it on now, it started making baaad noises and I think it's going to fail. So I am looking for replacement!
I have seen this pump in previous page somewhere (http://www.ebay.com/itm/381066536924?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT) and I dont like the $25 shipping to EU, so I have found this http://www.aliexpress.com/store/product/1pc-10W-DC-12V-Water-Cooling-DC-Pump-Tank-250ML-F-CPU-CO2-Laser-Water-Cooled/627093_1071768931.html with free shipping.

So my question is if this pump will fit. I am total newbie when it comes to those fittings and tube sizes :/ Thanks!

I've the same problem. My syscooling pump broken down in 2 month after mining start. So I changed low-quality chinease pump to reliable German heating circulation pump (for example like this: http://productfinder.wilo.com/en/COM/productrange/0000000a0000166700020023/fc_range_description/). And it works good about 8 month. (You can look my old topic: https://bitcointalksearch.org/topic/antminer-c1-997462. In russian, google translate will help Wink

)

The cast iron is a little bit overkill

. But you did pick a tank of a pump it looks like. I think the best is somewhere between the syscooling and that pump. The ebay one I have linked a lot is a great pump for open water cooling systems.

It's worth mentioning the syscooling pumps during batch 1 (possibly little into batch 2 cant remember) were tested dry and this put plastic shards in many in places they should not be. So high failure rate. Later pumps that were not used dry were suppose to last longer (I did not test this as I already had replaced my pumps before my replacement syscooling pumps came).

uralcryptocoin

sr. member

Activity: 1042

Merit: 328

SIGNATURE CREATION by uralcryptocoin

Quote from: Didldak on September 24, 2015, 10:32:46 AM

Hello guys,

my syscooling pump has been offline for few months and after I turned it on now, it started making baaad noises and I think it's going to fail. So I am looking for replacement!
I have seen this pump in previous page somewhere (http://www.ebay.com/itm/381066536924?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT) and I dont like the $25 shipping to EU, so I have found this http://www.aliexpress.com/store/product/1pc-10W-DC-12V-Water-Cooling-DC-Pump-Tank-250ML-F-CPU-CO2-Laser-Water-Cooled/627093_1071768931.html with free shipping.

So my question is if this pump will fit. I am total newbie when it comes to those fittings and tube sizes :/ Thanks!

I've the same problem. My syscooling pump broken down in 2 month after mining start. So I changed low-quality chinease pump to reliable German heating circulation pump (for example like this: http://productfinder.wilo.com/en/COM/productrange/0000000a0000166700020023/fc_range_description/). And it works good about 8 month. (You can look my old topic: https://bitcointalksearch.org/topic/antminer-c1-997462. In russian, google translate will help Wink

)

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: Didldak on September 24, 2015, 02:06:01 PM

Ok thanks, ordered =) Too bad it takes forever to deliver it to CZ :/

Not a problem! It is a good pump I think you will be happy with it.

And most importantly it words good

Didldak

full member

Activity: 150

Merit: 100

Oh boy!

Ok thanks, ordered =) Too bad it takes forever to deliver it to CZ :/

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: Didldak on September 24, 2015, 01:02:25 PM

And its direct fit on the stuff provided by syscooling? The tubes will fit on pump without issues?

They did for me, just use hot water on end of tubes it makes them expand then put it on. Hot water makes a big difference and much easier.

But yes I have used 2 of them on different miners and had no issues.

Didldak

full member

Activity: 150

Merit: 100

Oh boy!

And its direct fit on the stuff provided by syscooling? The tubes will fit on pump without issues?

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: Tupsu on September 24, 2015, 11:34:23 AM

Quote from: Didldak on September 24, 2015, 10:32:46 AM

Hello guys,

my syscooling pump has been offline for few months and after I turned it on now, it started making baaad noises and I think it's going to fail. So I am looking for replacement!
I have seen this pump in previous page somewhere (http://www.ebay.com/itm/381066536924?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT) and I dont like the $25 shipping to EU, so I have found this http://www.aliexpress.com/store/product/1pc-10W-DC-12V-Water-Cooling-DC-Pump-Tank-250ML-F-CPU-CO2-Laser-Water-Cooled/627093_1071768931.html with free shipping.

So my question is if this pump will fit. I am total newbie when it comes to those fittings and tube sizes :/ Thanks!

http://amzn.to/1PrlNZD
http://amzn.to/1gM7umg

I have used the ebay pump. I had pumps die and I was one to post ebay pump.

I used 2 of them for different miners and never had an issue with them. It is a little faster then regular pump, and bigger resivor. And I enjoyed the LED which is not really a big deal.

I suggest trying that pump if you need a new one.

Didldak

full member

Activity: 150

Merit: 100

Oh boy!

Thank you for tips, but "This item does not ship to XYZ, Czech Republic. Please check other sellers who may ship internationally. Learn more"

Tupsu

legendary

Activity: 1218

Merit: 1003

Quote from: Didldak on September 24, 2015, 10:32:46 AM

Hello guys,

my syscooling pump has been offline for few months and after I turned it on now, it started making baaad noises and I think it's going to fail. So I am looking for replacement!
I have seen this pump in previous page somewhere (http://www.ebay.com/itm/381066536924?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT) and I dont like the $25 shipping to EU, so I have found this http://www.aliexpress.com/store/product/1pc-10W-DC-12V-Water-Cooling-DC-Pump-Tank-250ML-F-CPU-CO2-Laser-Water-Cooled/627093_1071768931.html with free shipping.

So my question is if this pump will fit. I am total newbie when it comes to those fittings and tube sizes :/ Thanks!

http://amzn.to/1PrlNZD
http://amzn.to/1gM7umg

Didldak

full member

Activity: 150

Merit: 100

Oh boy!

Hello guys,

my syscooling pump has been offline for few months and after I turned it on now, it started making baaad noises and I think it's going to fail. So I am looking for replacement!
I have seen this pump in previous page somewhere (http://www.ebay.com/itm/381066536924?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT) and I dont like the $25 shipping to EU, so I have found this http://www.aliexpress.com/store/product/1pc-10W-DC-12V-Water-Cooling-DC-Pump-Tank-250ML-F-CPU-CO2-Laser-Water-Cooled/627093_1071768931.html with free shipping.

So my question is if this pump will fit. I am total newbie when it comes to those fittings and tube sizes :/ Thanks!

Topic: ANTMINER C1 Discussion and Support Thread - page 3. (Read 129144 times)