ANTMINER C1 Discussion and Support Thread - page 9.

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

Quote from: dunand on June 19, 2015, 06:04:41 AM

Do you know the electricity you are pulling? Where ca I download this binary?

Quote from: Sweminer777 on June 18, 2015, 10:07:00 PM

i guess this is the best result yet

256 at 0665 volts , best clocks have been moderated in my conclusion Roll Eyes

.

Quote from: imagina on June 19, 2015, 09:53:34 AM

https://www.nicehash.com/?p=software#asic

I just noticed something, don't use nicehash software.

i woke up this morning and it was not hashing for my wallet, It got hacked in the night and had a custom wallet and hashing for nicehash.

i guess the software they provide is doing this, really bad and abusive! i am reverting.

1NH8i5MPB16K57fNLXeeffBXD3mHhufviR

This is the wallet it was mining for and at nicehash stratum poool. i just rebooted and it dissapeared but i got a 3rd adress on the setup up for mining pool.

0mine
1mine
2mine
3 nicehash

Now the question is, how to acces to remove hes pool, after resetting my pools are still there, i guess hes is hidding as it did after rebooting.

Edit: it kept on after swapping firmware, i had to reflash entire SD card

imagina

newbie

Activity: 35

Merit: 0

https://www.nicehash.com/?p=software#asic

dunand

hero member

Activity: 637

Merit: 502

Do you know the electricity you are pulling? Where ca I download this binary?

Quote from: Sweminer777 on June 18, 2015, 10:07:00 PM

i guess this is the best result yet

256 at 0665 volts , best clocks have been moderated in my conclusion Roll Eyes

.

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

i guess this is the best result yet

256 at 0665 volts , best clocks have been moderated in my conclusion Roll Eyes

.

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

Quote from: notlist3d on June 18, 2015, 06:23:19 PM

Quote from: Sweminer777 on June 17, 2015, 05:42:57 AM

Quote from: dogie on June 16, 2015, 05:05:07 PM

Quote from: Sweminer777 on June 16, 2015, 02:45:09 PM

Main fan is very loud , going at 1800rpm.

Oh sweet, innocent child Tongue

You have yet to experience the glorious road of 5,000rpm 120mm fans.

Hahaha i wll swap the fans for some more efficients, they look pretty cheap to be honest Tongue

Edit ;

AFter some serious testing, undervolting and some not some powerull overclock,0 have been the most efficient yet

256.25 mhz at 0660 volts getting stable 1.2thz

Edit; Btw Does it matter to set higher Difficulty level if clock at 270mhz? and putting difficulty at /1+1536 ?

Most pools will do difficulty automatically at this point. What pool are you using?

As far as C1 you can even add fan's to the radiator very easy. I know I had some free after rebate fan's (they were around 3000 rpm) I put those on other side of radiator for a push/pull .

Ai am doing 268 atm at 0680 volt whit NiceHash modified Firmware 4.9 and its holding steady and fine actuaylly.

I added an extra fan for outblow, but thinkt to swap all the fans on outblow as it should suck more air inside the radiator.

Still checking most quiet possibility on cooling.

I got the radiator outside atm so temps have been really cool around 27-30 i guess it wont go up from 40 it havent and whit lower volt it should produce less heat.

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: Sweminer777 on June 17, 2015, 05:42:57 AM

Quote from: dogie on June 16, 2015, 05:05:07 PM

Quote from: Sweminer777 on June 16, 2015, 02:45:09 PM

Main fan is very loud , going at 1800rpm.

Oh sweet, innocent child Tongue

You have yet to experience the glorious road of 5,000rpm 120mm fans.

Hahaha i wll swap the fans for some more efficients, they look pretty cheap to be honest Tongue

Edit ;

AFter some serious testing, undervolting and some not some powerull overclock,0 have been the most efficient yet

256.25 mhz at 0660 volts getting stable 1.2thz

Edit; Btw Does it matter to set higher Difficulty level if clock at 270mhz? and putting difficulty at /1+1536 ?

Most pools will do difficulty automatically at this point. What pool are you using?

As far as C1 you can even add fan's to the radiator very easy. I know I had some free after rebate fan's (they were around 3000 rpm) I put those on other side of radiator for a push/pull .

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

Quote from: dogie on June 16, 2015, 05:05:07 PM

Quote from: Sweminer777 on June 16, 2015, 02:45:09 PM

Main fan is very loud , going at 1800rpm.

Oh sweet, innocent child Tongue

You have yet to experience the glorious road of 5,000rpm 120mm fans.

Hahaha i wll swap the fans for some more efficients, they look pretty cheap to be honest Tongue

Edit ;

AFter some serious testing, undervolting and some not some powerull overclock,0 have been the most efficient yet

256.25 mhz at 0660 volts getting stable 1.2thz

Edit; Btw Does it matter to set higher Difficulty level if clock at 270mhz? and putting difficulty at /1+1536 ?

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: Sweminer777 on June 16, 2015, 02:45:09 PM

Main fan is very loud , going at 1800rpm.

Oh sweet, innocent child Tongue

You have yet to experience the glorious roar of 5,000rpm 120mm fans.

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

Quote from: dunand on June 16, 2015, 01:16:41 PM

Anyone here repasted a C1? Better stability?

Hmm not yet, but considering doing it ,if i can find some good and cheap pasta might mount a 80mm fans inside the outside coolers still inspecing the space and possibilities for further cooldown as silent as possible.

Main fan is very loud , going at 1800rpm.

dunand

hero member

Activity: 637

Merit: 502

Anyone here repasted a C1? Better stability?

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

i am running fine at aorund 262 whit 745 volts, no problems at all, doing steady 1th to 1.2th at 45c on the heat some lower i gues the last one is guetting hottest.

Still doing some research, but found out that at stock volts clocking is much more stable whit no errors.

268 steady and stable at 0755 volts at 38c-40c temp

275 at 0765 is looking reaaly steady aswell doing 1.2th steady at 40c-42c temp

262 at 760 is the most stable i have found now, 1200-1300 ghz as lowest 1.1 sometimes temps ar areound 38-40c on a room of 26c.

dunand

hero member

Activity: 637

Merit: 502

I run one stock
250 760 for 1008Mhs @ 790 watts
I have one underclocked to
200 675 for 805Mhs @ 535 watts

Sadly the underclocked show me some "x" if I try to put it back to 250M 0.760V. But he have no problems @ 200 675.

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: Sweminer777 on June 15, 2015, 02:03:18 PM

Is there maybe some chart of overclocking, i have been tweaking from 250 to 270 mhz ant down from 0660 up to 0810 volts, haven't been able to get past the 520 mark, running 2x boards atm. might need to connect all 4 boards maybe to get it stable ?

Temps are stable between 30-35 at a room of 20-25 celcius. How high in volts can i go whitout damaging the boards?

810 is already too high really, I wouldn't run 24/7 higher than 780. Remember that C1 boards are already clocked fast compared to S3 boards and they're not that different.

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

Is there maybe some chart of overclocking, i have been tweaking from 250 to 270 mhz ant down from 0660 up to 0810 volts, haven't been able to get past the 520 mark, running 2x boards atm. might need to connect all 4 boards maybe to get it stable ?

Temps are stable between 30-35 at a room of 20-25 celcius.

How high in volts can i go whitout damaging the boards?

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: Sweminer777 on June 15, 2015, 03:59:38 AM

I still having issues whit login, I have Used the Restore image but it seems to not work, Password don't work, i have tried root root, admin admin, root admin, admin root so far no clues Huh

do i need to format the sd card?

Edit : i figured it out thanks ! root root was the password after win32 diskmng boot format

Glad it all worked out! You should be good to go but let us know if any other issues.

Happy Mining!

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

I still having issues whit login, I have Used the Restore image but it seems to not work, Password don't work, i have tried root root, admin admin, root admin, admin root so far no clues Huh

do i need to format the sd card?

Edit : i figured it out thanks ! root root was the password after win32 diskmng boot format

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: Sweminer777 on June 15, 2015, 02:16:15 AM

Quote from: dogie on June 14, 2015, 09:43:07 PM

Quote from: notlist3d on June 14, 2015, 07:23:54 PM

Quote from: Sweminer777 on June 14, 2015, 06:07:41 PM

My c1 is not reseting whit the reset button. i am using Cooler Master Real Power M1000 1000w

I can get to SSH login but cant login previous owner didnt give me the pass...

any solution to this? Huh

Yes luckily with the SD card it is very easy to recover. You can use Win32DiskImager or others and put the image on the sd card. If you use one of the restore images throughout though this thread it will be default password's.

There's a link in post #2 of the thread to an image posted on mega. Time travellers feel free to PM me if it goes down, I have a copy.

Thanks i readed the whole faq treadh even before hand and missed it, took me a while to find it, Maybe Blacken the letters and make them bigger, they are kinda smaller font size than the rest of the post Grin

thanks anyways!

Not a problem! Let us know if any issues but that should fix it up with default password again

Happy Mining.

Sweminer777

hero member

Activity: 754

Merit: 500

1xBit the largest casino

Quote from: dogie on June 14, 2015, 09:43:07 PM

Quote from: notlist3d on June 14, 2015, 07:23:54 PM

Quote from: Sweminer777 on June 14, 2015, 06:07:41 PM

My c1 is not reseting whit the reset button. i am using Cooler Master Real Power M1000 1000w

I can get to SSH login but cant login previous owner didnt give me the pass...

any solution to this? Huh

Yes luckily with the SD card it is very easy to recover. You can use Win32DiskImager or others and put the image on the sd card. If you use one of the restore images throughout though this thread it will be default password's.

There's a link in post #2 of the thread to an image posted on mega. Time travellers feel free to PM me if it goes down, I have a copy.

Thanks i readed the whole faq treadh even before hand and missed it, took me a while to find it, Maybe Blacken the letters and make them bigger, they are kinda smaller font size than the rest of the post Grin

thanks anyways!

dogie

legendary

Activity: 1666

Merit: 1185

dogiecoin.com

Quote from: notlist3d on June 14, 2015, 07:23:54 PM

Quote from: Sweminer777 on June 14, 2015, 06:07:41 PM

My c1 is not reseting whit the reset button. i am using Cooler Master Real Power M1000 1000w

I can get to SSH login but cant login previous owner didnt give me the pass...

any solution to this? Huh

Yes luckily with the SD card it is very easy to recover. You can use Win32DiskImager or others and put the image on the sd card. If you use one of the restore images throughout though this thread it will be default password's.

There's a link in post #2 of the thread to an image posted on mega. Time travellers feel free to PM me if it goes down, I have a copy.

notlist3d

legendary

Activity: 1456

Merit: 1000

Quote from: Sweminer777 on June 14, 2015, 06:07:41 PM

My c1 is not reseting whit the reset button. i am using Cooler Master Real Power M1000 1000w

I can get to SSH login but cant login previous owner didnt give me the pass...

any solution to this? Huh

Yes luckily with the SD card it is very easy to recover. You can use Win32DiskImager or others and put the image on the sd card. If you use one of the restore images throughout though this thread it will be default password's.

Topic: ANTMINER C1 Discussion and Support Thread - page 9. (Read 129188 times)