Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 26. (Read 125923 times)
should I tweak boards one by one or globally?
Hey blissz, I just changed the original firmware with yours, but I can't set it up properly for not having the HW errors. Even at 400Mhz on all, global and on all chains, I still have HW. What do you suggest?
Try a higher voltage setting when you are at lowest maybe 1-2, every hashboars is different, you must try.
Hey blissz, I just changed the original firmware with yours, but I can't set it up properly for not having the HW errors. Even at 400Mhz on all, global and on all chains, I still have HW. What do you suggest?
I tried the latest proper release (not the beta) and after about an hour one of my cards would fail dramatically on normal settings. Flashed back to latest firmware from BM and problem has disappeared at what one would assume are the same settings.
Does the Blissz release include fixes from the latest BM D3 firmware?
Loved the options this gave me to optimise each board but I'd be restarting the unit every hour~ to enjoy the privilege. Definitely staying tuned for updates though!
Does the Blissz release include fixes from the latest BM D3 firmware?
Loved the options this gave me to optimise each board but I'd be restarting the unit every hour~ to enjoy the privilege. Definitely staying tuned for updates though!
I will post an update of the Beta firmware soon. It will help you if you have boards that go into xxxx very often. (it's based on the newest source / rewritten all code)
i already setting using recommend blissz fw and got 950watt with 17.700mhs
my temp also cool down to 78 below.. before my d3 temp around 85-90
will try to setting another 10 d3..
my temp also cool down to 78 below.. before my d3 temp around 85-90
will try to setting another 10 d3..
Do you know how to estimate the real power consumption? I do not have device to measure it.
Currently I also get it down to 475 and 5 volt (or 4 still good), 17400. What watt can I estimate?
i estimate with wattmeter. and i do try and error to get what i want for my setting
for now, i adjust to make my machine work at 1000watt and temp under 80.
roughly i can get 18ghz for this setting.
i already setting using recommend blissz fw and got 950watt with 17.700mhs
my temp also cool down to 78 below.. before my d3 temp around 85-90
will try to setting another 10 d3..
my temp also cool down to 78 below.. before my d3 temp around 85-90
will try to setting another 10 d3..
Do you know how to estimate the real power consumption? I do not have device to measure it.
Currently I also get it down to 475 and 5 volt (or 4 still good), 17400. What watt can I estimate?
@Blissz: If your pools go down (unlikely, but possible), and the 2 hour timer triggers the devminer switch for the 1m50s and finds that both of the dev pools are dead... what happens? Does cgminer restart? If so, then after 5 minutes, it attempts to connect to dev pools again, finds them dead, and cgminer restarts... ad nausium until the dev pools come back? This is a pretty important thing to me as I rent out my machines and want high reliability for my renters and don't want to screw you out of your much deserved devfee.
Just block it in your firewall and never mine the dev pool duh
Or download awesome miner. Have a trigger for everytime it changes to dev pool to then change pool back to main pool. Done
Not the problem, or an answer.
Perfect answer
i already setting using recommend blissz fw and got 950watt with 17.700mhs
my temp also cool down to 78 below.. before my d3 temp around 85-90
will try to setting another 10 d3..
my temp also cool down to 78 below.. before my d3 temp around 85-90
will try to setting another 10 d3..
One of my D3's will only load the main page (with nothing on it) and won't let me go to any other pages to reboot or flash, etc. I tried the reset with a paperclip, but no go. Any ideas? Thank you
I think,
That page is probably a cached page.
The real page probably switched ip address.
You will have to find it again.
Important, some routers assign LAN and Wifi separately and it IS POSSIBLE your laptop is on the same ip as the rebooted d3.
I set my router to always assign the Miner to like a higher address so it never gets mixed with them. (DMZ).
M
Many thanks, I just had to go find it!
There is more need option , which shoudl be in firmware - auto reeboot if temp high on chip !
I don't know how, but after reboot sometimes chip temp got already 100 + stp....Need to reboot again, till temp on chip set up stable under 85 stp...
I don't know how, but after reboot sometimes chip temp got already 100 + stp....Need to reboot again, till temp on chip set up stable under 85 stp...
One of my D3's will only load the main page (with nothing on it) and won't let me go to any other pages to reboot or flash, etc. I tried the reset with a paperclip, but no go. Any ideas? Thank you
I think,
That page is probably a cached page.
The real page probably switched ip address.
You will have to find it again.
Important, some routers assign LAN and Wifi separately and it IS POSSIBLE your laptop is on the same ip as the rebooted d3.
I set my router to always assign the Miner to like a higher address so it never gets mixed with them. (DMZ).
M
My antminer D3 has no micro SD card slot! is that normal?
it's in the back facing the hashing boards on the controller board.
My antminer D3 has no micro SD card slot! is that normal?
One of my D3's will only load the main page (with nothing on it) and won't let me go to any other pages to reboot or flash, etc. I tried the reset with a paperclip, but no go. Any ideas? Thank you
jojo6865 - I put my copy of Antminer-D3-20171202_0-blissz.tar.gz at https://drive.google.com/file/d/1WOMsmBXoJXIFvcHJdiw1WtLYDoSaUEX0/view
Hope that helps.
Hope that helps.
Thanks so much exactly what i needed
For everyone talking about AwesomeMiner here. I again want to suggest this open source and free alternative:
https://github.com/anselal/antminer-monitor
Killer feature is that you can add in email alerts when a miner is down or too hot, or chips are missing, etc.
I was able to code in the email stuff following this: https://github.com/anselal/antminer-monitor/issues/19
I'd be happy to assist anyone with getting their stuff up to speed on this.
https://github.com/anselal/antminer-monitor
Killer feature is that you can add in email alerts when a miner is down or too hot, or chips are missing, etc.
I was able to code in the email stuff following this: https://github.com/anselal/antminer-monitor/issues/19
I'd be happy to assist anyone with getting their stuff up to speed on this.
Hi @blissz... hi folks...
What is maximun Hr/s that i can expect at lowest power consumpion (750/800w) with latest blissz release?
What is maximun Hr/s that i can expect at lowest power consumpion (750/800w) with latest blissz release?
I'm running 16.6GH at 900W
Great! I think it's a good compromise to do some altcoins... i'll try blissz firmware.
Anyone have any idea how to keep Priviliged API access in Awesome miner? If I reboot the D3 using the web page it comes back with Restricted API access, and then you have to Configure API access in antminer again, which causes another reboot. Annoying when messing with settings...
Privileged API Access on Antminers it's a built in feature of Awesome Miner. I think u know how to unlock this feature, but remember to reboot miners only via AWMiner... rebooting on browser web page resets the default Restricted API Access. Ther's no way to keep Privileged API Access using both interfaces. Manage your Antminers on web page (with Restricted AWMiner features)... or manage them only via AWMiner keeping Privileged API Access.
Yeah, I meant to say "you have to Configure API access in Awesome Miner again", not in antminer.
That sucks that you can't reboot using the web page, if you want to test out new settings I guess just use the web page until it's stable, then configure the access again in Awesome Miner when you are happy with the settings. Minor annoyance I guess...
jojo6865 - I put my copy of Antminer-D3-20171202_0-blissz.tar.gz at https://drive.google.com/file/d/1WOMsmBXoJXIFvcHJdiw1WtLYDoSaUEX0/view
Hope that helps.
Hope that helps.
Yeah the only one on the main page is the latest one i am looking for the 02/12 one
sorry thought u were looking for 10/12 i assumed that u updated for beta test
Yeah the only one on the main page is the latest one i am looking for the 02/12 one
Jump to: