Pages:
Author

Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 27. (Read 125926 times)

full member
Activity: 155
Merit: 100
Does anyone happen to have a copy of the 02/12 firmware i upgraded and my D3's do not seem to like the new version
check first post
newbie
Activity: 4
Merit: 0
Does anyone happen to have a copy of the 02/12 firmware i upgraded and my D3's do not seem to like the new version
newbie
Activity: 19
Merit: 0
Hi @blissz... hi folks...

What is maximun Hr/s that i can expect at lowest power consumpion (750/800w) with latest blissz release?

I'm running 16.6GH at 900W

Great! I think it's a good compromise to do some altcoins... i'll try blissz firmware.

Anyone have any idea how to keep Priviliged API access in Awesome miner?  If I reboot the D3 using the web page it comes back with Restricted API access, and then you have to Configure API access in antminer again, which causes another reboot.  Annoying when messing with settings...

Privileged API Access on Antminers it's a built in feature of Awesome Miner. I think u know how to unlock this feature, but remember to reboot miners only via AWMiner... rebooting on browser web page resets the default Restricted API Access. Ther's no way to keep Privileged API Access using both interfaces. Manage your Antminers on web page (with Restricted AWMiner features)... or manage them only via AWMiner keeping Privileged API Access. Wink
newbie
Activity: 50
Merit: 0
Anyone have any idea how to keep Priviliged API access in Awesome miner?  If I reboot the D3 using the web page it comes back with Restricted API access, and then you have to Configure API access in antminer again, which causes another reboot.  Annoying when messing with settings...
jr. member
Activity: 37
Merit: 1
Hi @blissz... hi folks...

What is maximun Hr/s that i can expect at lowest power consumpion (750/800w) with latest blissz release?

I'm running 16.6GH at 900W
newbie
Activity: 50
Merit: 0
hi blissz..
can i know this one still valid?
dont know of this hw error okay or not.
this setting i just want to keep my temp under 80 and get little low voltage than before ..
i got around 900watt for this 17.7k ghz


https://imgur.com/yoGj0Ud
sr. member
Activity: 336
Merit: 258
Hi @blissz... hi folks...

What is maximun Hr/s that i can expect at lowest power consumpion (750/800w) with latest blissz release?

It really depends per unit. I would say it varies between 15 and 17 Gh/s
newbie
Activity: 19
Merit: 0
Hi @blissz... hi folks...

What is maximun Hr/s that i can expect at lowest power consumpion (750/800w) with latest blissz release?

at 400MHz @lowest voltage i was averaging something like 15GH/s. wasn't happy with all the HWs i was getting so i abandoned that pretty quickly.
at 450MHz @ voltage step 8 i'm getting 16.4GH/s (i have not checked wattage yet).
at 525MHz @ voltage step 13 was very close to stock, 19.3GH/s at 1100W.
newbie
Activity: 19
Merit: 0
Hi @blissz... hi folks...

What is maximun Hr/s that i can expect at lowest power consumpion (750/800w) with latest blissz release?
full member
Activity: 218
Merit: 100
I'm working with Awesome Miner to switch between pools and coins. Unfortunately
the D3 only allows three pools to be preconfigured, and AM can only switch between these three.

Blissz , could you please extend the number of preconfigured pools to let's say 10 ? This would make profitability and
usability much better.

And thank you for your work so far. For me, I don't care if your fee cut's my income on 1 or 5% ,
everybody here is free to decide to use it or not, I don't understand why people complain.
For me the advantages are worth much more than 5%.

Please focus on the features, the better your fw gets, the less the whine will be.


In Awesome Miner you can add more then the 3 pools to the Miner.
use add pool, but it works only when you have API access from Awesomeminer
newbie
Activity: 19
Merit: 0
just wondering if there is firmware like this for the S9?

really good stuff here, thanks, not so much an expensive hair driers now i found you...

u get a % correct?

There might be, you'd have to check the Bitcoin Hardware section for that since this is an AltCoin miner.
His cut is 1.5% (or 1.8%?) mining time to his pools every 2 hours (1m50s/2h)
full member
Activity: 134
Merit: 100
First DJ to play gigs for Bitcoin & Crypto Guru
just wondering if there is firmware like this for the S9?

really good stuff here, thanks, not so much an expensive hair driers now i found you...

u get a % correct?
newbie
Activity: 21
Merit: 0
I'm working with Awesome Miner to switch between pools and coins. Unfortunately
the D3 only allows three pools to be preconfigured, and AM can only switch between these three.

Blissz , could you please extend the number of preconfigured pools to let's say 10 ? This would make profitability and
usability much better.

And thank you for your work so far. For me, I don't care if your fee cut's my income on 1 or 5% ,
everybody here is free to decide to use it or not, I don't understand why people complain.
For me the advantages are worth much more than 5%.

Please focus on the features, the better your fw gets, the less the whine will be.

newbie
Activity: 19
Merit: 0
How much time does it spend in the dev pool every 2 hours?

1m50s
newbie
Activity: 38
Merit: 0
How much time does it spend in the dev pool every 2 hours?
sr. member
Activity: 336
Merit: 258
Currently running on 400M voltage 4 with no errors and under 60c. Thank you blissz.

Good to hear it works for you!
sr. member
Activity: 336
Merit: 258
I will try too but i need only one feature:
If fan stops for some reason hardware/software and temperature goes over 100 degrees..
i want cgminer process killed.
I do not want any reboots or cgminer restarts just full stop.
This is the only reason which stops me from using this version.

It will be in, in the next version
newbie
Activity: 18
Merit: 10
Currently running on 400M voltage 4 with no errors and under 60c. Thank you blissz.
sr. member
Activity: 336
Merit: 258
If I were to reduce the frequency to the lowest value, along with the lowest voltage, would the power consumption continue to drop? I currently get around 730w, just wondering if possible to go lower.

yes it will go down with the frequency in quite a linear curve. So let's say 400Mhz = 730Watt at the lowest voltage, then 200Mhz would be ~365Watt at the lowest voltage for example.
newbie
Activity: 56
Merit: 0
Was the beta v2.02 not meant to run for any length of time?  I ran it for ~10 hours and for some reason my Chain 3 is much worse now in terms of HW failures.  I set it on the lowest voltage and before I ran the beta (but ran many different Blissz firmware updates before that) it was fine around 450.  Now it can't get above 419 without multiple HW failures per minute.  Anyone else experience this?

I'd like to add that I've been very happy with what Blissz has been able to do thus far, so thank you!

Yep, that's my problem too.

I have a new highly sensitive chain that WAS my best chain, now is my worst.

I am afraid the aggressive freq/voltage search during autotune screwed my machine/chain up.

No answers? I cannot mine at speeds higher than 19 now, I was at 20.9 before.

It looks like they auto tuned themselves right out of being tuned...




Can I get an answer to one question.

Should I ignore HW errors when temps are ok?


Info: Newly rebooted New version of 10/12. Set everything as described.

This goes on at a pace of 118 every 20 minutes or so.

Chain#   ASIC#   Frequency   MH/S(RT)   HW   Temp(PCB)   Temp(Chip)   ASIC status
1                   60               494    6026.14    0            54                     71
oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooo
2                   60               438    5400.08    118         47                     61
oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooo
3                   60               494    6154.90    0             57                     72

When I installed Beta, did a test at lowest, did a test at 9V sent you the stuff.

I tried 12 or 13V with autotune and immediately saw a temp of 256 on the Chain 2. Chip temp was fine....(I mean like 79).

I reverted back to old 12 /10 that I had. Now chain 2 overreacts to temps. I just disregard as long as no asic fail and no shown temperatures to worry about. But watching it Hurts.

Is there a way change temp offset for chain two only to like -13? It's at -3 now, just like the other two.

Thanks for your answers in advance, sorry to bother you.

M




Well, due to the overwhelming responses and help I get, this is what I did, Ignore them....

Chain#   ASIC#   Frequency   MH/S(RT)       HW   Temp(PCB)   Temp(Chip)   ASIC status
1                 60                  556    6896.92        0          53                    73
oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooo
2                 60                  537    6623.69       278        50                    68
oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooooooo oooo
3                 60                  531    6611.15        0           56                    73

Works fine for hours now.

Still need a fix, if there is a possibility for one.

Thanks, again, in advance, kindly, for any response, or help provided to me.

Patient 1

M
Pages:
Jump to: