Topic: ANTMINER S3+ Discussion and Support Thread - page 437. (Read 710164 times)
Yeah thanks. I will request also invoice in eur
Here in Canada I would pay a small fortune in taxes.
Batch 2
Pay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
Congrats! Wish you a quick deliveryPay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
I also got the delivery info and am following the tracking, unfortunately the weekend seems to put a bit of a pause, so current delivery of my B1 order is now expected on Wednesday.
Cheers
Thanks !!I'm from Spain . If I have to pay something for customs I will tell you how much.
no wonder it is called the 'lucky country'...)Hopefully your customs fees are not too painful.
Cheers
Batch 2
Pay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
Congrats! Wish you a quick deliveryPay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
I also got the delivery info and am following the tracking, unfortunately the weekend seems to put a bit of a pause, so current delivery of my B1 order is now expected on Wednesday.
Cheers
Thanks !!I'm from Spain . If I have to pay something for customs I will tell you how much.
Simple the shipping declaration from bitmain is in dollar terms.
I found it is for some others at $900 to $950 for two miner pack.
If you want the exact rate contact bitmain at [email protected] or use the PM of this forum.
Batch 3 - label printed!
Why every newbie buy from bit main
You will never roi
Because diff go so up
Because of bit main hardware
So the only which is earn is bitmain no one else
You never roi your money you spent
You will never roi
Because diff go so up
Because of bit main hardware
So the only which is earn is bitmain no one else
You never roi your money you spent
I take this as a hobbie and it will roi. Anyway what are you doing here if you hate bitmain?
Most of my S1 Antminers did reach ROI. Bitmain miners have a very competitive cost/GH/sec as well as high reliability, no wonder that there was a massive response to the S3 launch. And yes, it is a hobby.
Cheers
Batch 2
Pay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
Congrats! Wish you a quick deliveryPay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
I also got the delivery info and am following the tracking, unfortunately the weekend seems to put a bit of a pause, so current delivery of my B1 order is now expected on Wednesday.
Cheers
Thanks !!I'm from Spain . If I have to pay something for customs I will tell you how much.
Why every newbie buy from bit main
You will never roi
Because diff go so up
Because of bit main hardware
So the only which is earn is bitmain no one else
You never roi your money you spent
You will never roi
Because diff go so up
Because of bit main hardware
So the only which is earn is bitmain no one else
You never roi your money you spent
Most order are not from newbie if you do a search in forum threads.
Somewhat Possible with S3 in btc terms else, At-least in Fiat terms. Miners are hobbyists too.
Difficulty increase substantially lower now. % of increase will be lower in the future too.
Bitmain hardwares are the most efficient J/G
I get Free electricity at my dorm! I wish I could buy one so I could mine. Would be fun!
Enjoy your ant miners guys.
Enjoy your ant miners guys.
Batch 2
Pay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
Congrats! Wish you a quick deliveryPay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
I also got the delivery info and am following the tracking, unfortunately the weekend seems to put a bit of a pause, so current delivery of my B1 order is now expected on Wednesday.
Cheers
But the problem is that one card of one of S3's is not working at all!
I have checked everything power, cabling, anything I can imagine but it persist and not working at all!
Any ideas what should I do?
Did you try moving the cables to the other ports?
Otherwise, I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.
Yes, tried it and open it up as well but found no problem yet!
Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!
It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.
there is no shipment problem seems on the device.
But I found a clue.
I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.
Now the other board is mining and it's temperature increased.
So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
Cheers
ribbon cables are ok. tried this before.
Cheers
As you told I replaced the mainboard of bad device with main board of good device and now the device is working with two asic boards ok, so it's obvious that the main board of the bad device have some problem.
I will ask bitmain for a replacement for mainboard and while then my device can mine half capacity.
Thanks a lot guys!
Hi,
RMA request is accepted, PMed you just now.
Thank you! you can send it with my other orders.
Congrats!
Why every newbie buy from bit main
You will never roi
Because diff go so up
Because of bit main hardware
So the only which is earn is bitmain no one else
You never roi your money you spent
You will never roi
Because diff go so up
Because of bit main hardware
So the only which is earn is bitmain no one else
You never roi your money you spent
I take this as a hobbie and it will roi. Anyway what are you doing here if you hate bitmain?
Batch 2
Pay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
Pay:1.48 BTC
Confirm:1.48 BTC Paid
Shipped
Valid 2014-07-02 10:03:41.0
Yesssss!!!!!!
My batch 2 order is on its way.
Info from Bitmain Website
Order Placed
Date: 2014-07-04 12:56:46
Payment Confirmed:
Date 2014-07-04 14:07:48
Shipped:
Date 2014-07-20 08:18:59
Hopefully will receive on Tuesday, and hope all arrives safely.
Info from Bitmain Website
Order Placed
Date: 2014-07-04 12:56:46
Payment Confirmed:
Date 2014-07-04 14:07:48
Shipped:
Date 2014-07-20 08:18:59
Hopefully will receive on Tuesday, and hope all arrives safely.
But the problem is that one card of one of S3's is not working at all!
I have checked everything power, cabling, anything I can imagine but it persist and not working at all!
Any ideas what should I do?
Did you try moving the cables to the other ports?
Otherwise, I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.
Yes, tried it and open it up as well but found no problem yet!
Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!
It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.
there is no shipment problem seems on the device.
But I found a clue.
I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.
Now the other board is mining and it's temperature increased.
So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
Cheers
ribbon cables are ok. tried this before.
Cheers
As you told I replaced the mainboard of bad device with main board of good device and now the device is working with two asic boards ok, so it's obvious that the main board of the bad device have some problem.
I will ask bitmain for a replacement for mainboard and while then my device can mine half capacity.
Thanks a lot guys!
Hi,
RMA request is accepted, PMed you just now.
Thank you! you can send it with my other orders.
BITMAIN Order Shipped B2's
• Order ID: 00XXXXXXXXXXXXXXXXXXXXXXXXXX
• Date: 2014-07-03 10:25:13
Fantastic! as promised on or just after the 20th
very happy!
• Order ID: 00XXXXXXXXXXXXXXXXXXXXXXXXXX
• Date: 2014-07-03 10:25:13
Fantastic! as promised on or just after the 20th
very happy!
But the problem is that one card of one of S3's is not working at all!
I have checked everything power, cabling, anything I can imagine but it persist and not working at all!
Any ideas what should I do?
Did you try moving the cables to the other ports?
Otherwise, I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.
Yes, tried it and open it up as well but found no problem yet!
Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!
It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.
there is no shipment problem seems on the device.
But I found a clue.
I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.
Now the other board is mining and it's temperature increased.
So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
Cheers
ribbon cables are ok. tried this before.
Cheers
As you told I replaced the mainboard of bad device with main board of good device and now the device is working with two asic boards ok, so it's obvious that the main board of the bad device have some problem.
I will ask bitmain for a replacement for mainboard and while then my device can mine half capacity.
Thanks a lot guys!
Hi,
RMA request is accepted, PMed you just now.
But the problem is that one card of one of S3's is not working at all!
I have checked everything power, cabling, anything I can imagine but it persist and not working at all!
Any ideas what should I do?
Did you try moving the cables to the other ports?
Otherwise, I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.
Yes, tried it and open it up as well but found no problem yet!
Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!
It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.
there is no shipment problem seems on the device.
But I found a clue.
I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.
Now the other board is mining and it's temperature increased.
So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
Cheers
ribbon cables are ok. tried this before.
Cheers
As you told I replaced the mainboard of bad device with main board of good device and now the device is working with two asic boards ok, so it's obvious that the main board of the bad device have some problem.
I will ask bitmain for a replacement for mainboard and while then my device can mine half capacity.
Thanks a lot guys!
But the problem is that one card of one of S3's is not working at all!
I have checked everything power, cabling, anything I can imagine but it persist and not working at all!
Any ideas what should I do?
Did you try moving the cables to the other ports?
Otherwise, I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.
Yes, tried it and open it up as well but found no problem yet!
Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!
It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.
there is no shipment problem seems on the device.
But I found a clue.
I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.
Now the other board is mining and it's temperature increased.
So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
Cheers
ribbon cables are ok. tried this before.
Cheers
But the problem is that one card of one of S3's is not working at all!
I have checked everything power, cabling, anything I can imagine but it persist and not working at all!
Any ideas what should I do?
Did you try moving the cables to the other ports?
Otherwise, I would open it up and look for any loose connections. Sometimes things get knocked loose during shipping.
Yes, tried it and open it up as well but found no problem yet!
Checked the controller cable, changed it with the other one! But absolutely nothing happened yet!
It happen during shipping with one of my S1, check for any loose capacitors or inductors on pcb.
there is no shipment problem seems on the device.
But I found a clue.
I connected control cable from main-board Socket-1 to Board 2 and from socket-2 to Board 1.
Now the other board is mining and it's temperature increased.
So it's obvious that there is some problem in mainboard and the Asic Boards and cables are ok.
Cheers
ribbon cables are ok. tried this before.
Jump to: