Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~ - page 10.

taserz

sr. member

Activity: 800

Merit: 294

Created AutoTune to saved the planet! ~USA

Quote from: dutchlincoln on October 03, 2018, 02:43:10 AM

power wise i agree, its not advised, but sometimes there are good reasons to do so.
Is there a way to get 14TH out of it?

I mean sure if you have really cheap power but you would need sub 4 cent power as efficiency goes out of whack on them.

dutchlincoln

member

Activity: 434

Merit: 30

power wise i agree, its not advised, but sometimes there are good reasons to do so.
Is there a way to get 14TH out of it?

taserz

sr. member

Activity: 800

Merit: 294

Created AutoTune to saved the planet! ~USA

Quote from: thierry4wd on October 02, 2018, 04:54:09 PM

if I can allow myself,

Original T9 + = 10.5Ths ==> 1450W at wall 220v
My T9 + = 12.5Ths ==> 1400W at wall 220V

Its worth it 2Th free! ?

Regards: p

But I agree 100% not to mount Bmminer S9 that VERY strongly risk giving the error "PIC Error" and brick one or more hash board ...

I have seen many people get unstable hashboards ocing t9

thierry4wd

sr. member

Activity: 446

Merit: 347

Quote from: taserz on October 02, 2018, 04:31:37 PM

T9+ is annoying to overclock and honestly not worth it. Don't do it also this one won't work.

if I can allow myself,

Original T9 + = 10.5Ths ==> 1450W at wall 220v
My T9 + = 12.5Ths ==> 1400W at wall 220V

Its worth it 2Th free! ?

Regards: p

But I agree 100% not to mount Bmminer S9 that VERY strongly risk giving the error "PIC Error" and brick one or more hash board ...

taserz

sr. member

Activity: 800

Merit: 294

Created AutoTune to saved the planet! ~USA

Quote from: dutchlincoln on October 02, 2018, 10:31:41 AM

Can i copy the Bmminer also on a T9+, or does it not work like that?

If not, how can i overclock the T9+?

T9+ is annoying to overclock and honestly not worth it. Don't do it also this one won't work.

dutchlincoln

member

Activity: 434

Merit: 30

Can i copy the Bmminer also on a T9+, or does it not work like that?

If not, how can i overclock the T9+?

sergw

member

Activity: 159

Merit: 12

ok, tested this bmminer on 20 my s9 asics 13.5T and 14.0T, so 15 works w/o any issues with bmminer880: overclocked up to 15T, 5 rest asics show 98-105C with bmminer880, replaced it with bmminer890 = 3 started to work good, rest 2 asics still work incorrectly with all bmminer versions (show chip temp over 100C even with stock 630 freq)

GDDRX

newbie

Activity: 2

Merit: 0

Quote from: taserz on October 02, 2018, 03:59:20 AM

Fan check is disabled already on this :0

Nice

Now need craft oil pool )) Roll Eyes

taserz

sr. member

Activity: 800

Merit: 294

Created AutoTune to saved the planet! ~USA

Quote from: GDDRX on October 02, 2018, 03:26:05 AM

Taserz,
How to disable fan check?
I want to test watercooling and more overclock settings, but how to kick off collers from boards without error "Fan lost".
Thx.

Fan check is disabled already on this :0

GDDRX

newbie

Activity: 2

Merit: 0

Taserz,
How to disable fan check?
I want to test watercooling and more overclock settings, but how to kick off collers from boards without error "Fan lost".
Thx.

Andartis

jr. member

Activity: 306

Merit: 7

Hey guys,
I have got 2 quite good binned miners. With the original fixed FW I am getting better results than with bmminer890. How can I check what voltage the original bmminer uses?

dutchlincoln

member

Activity: 434

Merit: 30

Quote from: AniceInovation on September 28, 2018, 10:01:45 PM

How lucky have you guys been with undervoltage?
How low can you get, how efficient can you be while keeping the default frequency?

i tried up to 400Mhz... Stayed 103 watts per terahsh. (on a 13.5T machine, running 880 software)

It was my idea as well, underclocking, and freeing up power, so be able to put more machines....

darn.. My power line is full, can't add any more... Angry

AniceInovation

donator

Activity: 446

Merit: 262

Interesting.

How lucky have you guys been with undervoltage?
How low can you get, how efficient can you be while keeping the default frequency?

tim-bc

full member

Activity: 538

Merit: 175

Quote from: Mousem40 on September 28, 2018, 03:21:29 AM

This is a good question. Has anyone else looked into this, and are you wasting your time OCing these units?

It's only profitable if you already have cheap power to begin with.

cfbtcman

member

Activity: 264

Merit: 16

Hi Taserz, where can i see the voltage is running is kernel log, just in your firmware?
Im looking in original kernel log of a machine and i cant see no information about voltage !

dutchlincoln

member

Activity: 434

Merit: 30

the 880
the others draw too much power for the stock psu.

Shad0wSmurf

jr. member

Activity: 59

Merit: 10

Quote from: dutchlincoln on September 28, 2018, 05:54:56 AM

intriguing...

Curious also, and as i had just laying around some miners and a watt meter, i have performed a little test:

500Mhz 10.8TH 4.9Amps 1120W w/th:103
550Mhz 11.8TH 5.35Amps 1220W w/th:103
600Mhz 12.8Th 5,8Amps 1330W w/th:103
650Mhz 13.7Th 6,25Amps 1445W w/th:105
700Mhz 14.4Th 6,8Amps 1570W w/th:109
793Mhz 15Th 7,7Amps 1750W w/th:116

overclocking is NOT profitable... (on this miner...)

i also have one running 793Mhz squirting 16.2TH. Assume numbers are equal, it would do 108W/TH

best: add miners...

Using which bmminer from this thread.

dutchlincoln

member

Activity: 434

Merit: 30

Quote from: Mousem40 on September 28, 2018, 03:21:29 AM

This is a good question. Has anyone else looked into this, and are you wasting your time OCing these units?

intriguing...

Curious also, and as i had just laying around some miners and a watt meter, i have performed a little test:

500Mhz 10.8TH 4.9Amps 1120W w/th:103
550Mhz 11.8TH 5.35Amps 1220W w/th:103
600Mhz 12.8Th 5,8Amps 1330W w/th:103
650Mhz 13.7Th 6,25Amps 1445W w/th:105
700Mhz 14.4Th 6,8Amps 1570W w/th:109
793Mhz 15Th 7,7Amps 1750W w/th:116

overclocking is NOT profitable... (on this miner...)

i also have one running 793Mhz squirting 16.2TH. Assume numbers are equal, it would do 108W/TH

best: add miners...

Mousem40

newbie

Activity: 37

Merit: 0

Quote from: Pirozhkov on September 25, 2018, 11:31:22 AM

S9 13.5Th + P3 Power PSU 2100w -> Fix 650M frimware -> bmminer880

0.08 $/kWh
750m - 15.7th - 1670w profit - $0.38
700m - 14.9th - 1540w profit - $0.44
650m - 13.9th - 1430w profit - $0.44

Overclocking is not profitable?

This is a good question. Has anyone else looked into this, and are you wasting your time OCing these units?

btc2017btc2017

member

Activity: 176

Merit: 10

Hi, does this send a fee to the dev or is it dev fee free? Does the dev take donations?

I have the 13.5 TH/s S9 with auto frequency. I've set the frequency to 800 MHz and using the 8.8v file, most of the time I see 16.6 TH/s, but sometimes I see a random value, is this nothing to worry about?

A few F5 refreshes clears the problem

I have another PSU on an E3 (860W), can I take the remaining 3 PCIe cable and connect it to one of the S9s hashboards and possibly use a total of 2340 watts on the S9 assuming the PCIe cables can handle 266W (22A).

What would be the max TH/s I'll be able to get?

I do have some 1800W PSUs onsite so I could try that on the S9 at the weekend.

Topic: Antminer S9 Volt Rocket Ship firmware mod! ~Time to Max Out Your Bitmain PSU~ - page 10. (Read 32696 times)