Avalon ASIC users thread - page 28. | Bitcointalksearch.org

biospehre

newbie

Activity: 8

Merit: 0

Quote from: SolarSilver on January 26, 2014, 11:50:06 AM

Quote from: biospehre on January 26, 2014, 07:13:53 AM

I cannot access to the web interface. Can you check my psu cable management. Cannot find anything on the web about my problem. Here are some pictures:
Do i have connected everything correct?

Accessing the web interface means guessing at what IP your TP-LINK module is configured too.. check the previous 2 pages in this thread... do you have an Ethernet uplink LED? Can you ping the unit? If not, try different subnets.

Can somebody post a picture of the correct power connection inside the Avalon Device?

This would be really nice...

SolarSilver

legendary

Activity: 1112

Merit: 1000

Quote from: biospehre on January 26, 2014, 07:13:53 AM

I cannot access to the web interface. Can you check my psu cable management. Cannot find anything on the web about my problem. Here are some pictures:
Do i have connected everything correct?

Accessing the web interface means guessing at what IP your TP-LINK module is configured too.. check the previous 2 pages in this thread... do you have an Ethernet uplink LED? Can you ping the unit? If not, try different subnets.

SolarSilver

legendary

Activity: 1112

Merit: 1000

Quote from: patnor1011 on January 26, 2014, 07:02:11 AM

Can someone have look at this and tell me what is wrong (I presume something is not right as numbers marked with red circle appear to be way too high)?
I have set it to balance so it mined on both pools I set.
This is new 200Gh unit with 2 modules and 160 chips.

http://i39.tinypic.com/2qlsqxg.jpg

Look at the more relevant tab:

Status -> Cgminer API Log

The field

Code:

[Device Hardware%] => 0.9269

should give you the right %

biospehre

newbie

Activity: 8

Merit: 0

Hello...

I got one of these Avalon Miners (Avalon 55nm)

I cannot access to the web interface. Can you check my psu cable management. Cannot find anything on the web about my problem. Here are some pictures:
Do i have connected everything correct?
My reseller told me only one CPU (8PIN) and one PCI-E Connector (6PIN)

Please check the pictures. I'am going crazy...

https://drive.google.com/folderview?id=0B-oHg9L2m0H5cGx6dGxsUDIzbXc&usp=sharing

thx

MrScrotes

newbie

Activity: 28

Merit: 0

Is Avalon still around ?

patnor1011

member

Activity: 114

Merit: 100

Can someone have look at this and tell me what is wrong (I presume something is not right as numbers marked with red circle appear to be way too high)?
I have set it to balance so it mined on both pools I set.
This is new 200Gh unit with 2 modules and 160 chips.

Gerronimo

newbie

Activity: 8

Merit: 0

Hi everybody.
Have bought used Avalon 55nm 230Ghs.
During 3 days where 4 delays in mining - had several delays for about 3 hours.

As I am advanced user in network I started fresh and loaded defaults.
But I have "Connection refused" - and it doesn't work at all.
firmware - 20131229
firewall - all allow
router - ZTE and android smartphone
Pools - btcguild
Started and stopped Cgminer process billon of times!

Any help.

Also I use computer USB connection and CGMiner

But I have no hashes at all.
http://i41.tinypic.com/ofaeio.jpg

rezilient

hero member

Activity: 574

Merit: 500

Quote from: rezilient on January 23, 2014, 05:15:18 PM

I have a customer who's getting the following Cgminer API error on his 230G Avalon2 clone (by CCBMC).

[Firmware Version] => 20131110
cgminer: 176747f
cgminer-openwrt-packages: 0e12b1b
luci: 346e3e7
Socket connect failed: Connection refused

He has confirmed the following for me:

- using pool stratum.btcguild.com:3333
- configuration page looks good, no typos
- API Allow is correctly set to "W:127.0.0.1"
- he can ping out to stratum.btcguild.com and IP resolves correctly
- "cgminer" process is not currently running when we check Processes tab
- he has tried many other pools aside from btcguild with no luck

Any idea what the problem might be? I tested the device before shipping and it was working fine.

Thanks for any help. I have been reading that updating the firmware might help, but I'm not sure where to get the firmware.

Hi guys. Okay we figured this out, although I'm still a bit confused. The "broadcast" address in his LAN settings was 192.168.0.255 however he was on the 192.168.1.X subnet so the broadcast was incorrect. However I checked my own 230G miner and it was configured the same, and working. I'm thinking maybe re-saving the LAN settings kicked something into working. Anyway, he is happy and it's hashing now. Thanks for the help!

Also here is the link to updated firmware, in case anyone needs it, shared by user studio1one in another thread.
http://downloads.canaan-creative.com/software/avalon/20131229/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-sysupgrade.bin

oofangoo

newbie

Activity: 2

Merit: 0

Hi guys, this probably been asked before but I couldn't find the solution.

Anyone had experience with the Avalon Asic II 55nm 2 modules (200GH/s) configuration get reset automatically when running for some time?

Been running for couple days now and had got the reset issue 5-6 times already.

The machine is running firmware 20131110 so not sure if it's firmware issue. I had 2 of these but appears only 1 has this issue so I guess might not be firmware issue.

Can you guys point me to the page where this was discussed, thanks

patnor1011

member

Activity: 114

Merit: 100

What does that HW -1327 mean?

Guava

member

Activity: 70

Merit: 10

Quote from: patnor1011 on January 24, 2014, 10:41:26 AM

I managed to get it running but something may be wrong...

HW count appears to be extremely high.

Looks normal to me. Look at DH%. HW ~3% is ok.

patnor1011

member

Activity: 114

Merit: 100

I managed to get it running but something may be wrong...

HW count appears to be extremely high.

dozerz

legendary

Activity: 2242

Merit: 1057

can anyone help with the error ava0 reset failed! not an avalon? (0:08 00 00 00)

this is a gen2 avalon connected by usb when the lan board died.

cgminer starts but then cycles through:

result return rate low, resetting
reset sequence sent
ava0: idling 24 miners

patnor1011

member

Activity: 114

Merit: 100

5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 0.297/0.334/0.459 ms

ping from diagnostics

Guava

member

Activity: 70

Merit: 10

Quote from: patnor1011 on January 24, 2014, 04:30:31 AM

Ok, so I managed to move on. Now I can connect to settings page. I went to status --- cgminer configuration and inserted pool/worker/password for 2 of them.
When I press save and apply I see action - spinning circle and quote applying changes. That goes on for several minutes:
Applying changes
/etc/config/cgminer

Last time I waited 10 minutes, still no change so I just went to system --- startup and on line where cgminer is I pressed restart - nothing happened.
I tried status---cgminer configuration---save and apply then go to system---startup and start on cgminer line again nothing.
Actually when I try restart cgminer it give me "Bad gateway" message.

Make sure your miner is connected to internet first. Try ping from "Diagnostics".
There's a NTP bug that prevent it from saving.

patnor1011

member

Activity: 114

Merit: 100

Is this where you start cgminer?

patnor1011

member

Activity: 114

Merit: 100

Ok, so I managed to move on. Now I can connect to settings page. I went to status --- cgminer configuration and inserted pool/worker/password for 2 of them.
When I press save and apply I see action - spinning circle and quote applying changes. That goes on for several minutes:
Applying changes
/etc/config/cgminer

Last time I waited 10 minutes, still no change so I just went to system --- startup and on line where cgminer is I pressed restart - nothing happened.
I tried status---cgminer configuration---save and apply then go to system---startup and start on cgminer line again nothing.
Actually when I try restart cgminer it give me "Bad gateway" message.

truckfan2

newbie

Activity: 3

Merit: 0

I recieved an avalon gen3 I believe as it has the 3255 chips in it and is a black cased unit. I have it running at 150 gh at freq 1000. When I raise the frequency higher it does not seem to like it even though the chips are rated at 1000 to 2000 freq. Is there a certain number multiplier I should be using to come up with the frequency? Also it is a 2 module unit with 40 chips per module and will only show work up to 16 workers even though I see a lot of people here post screenshots of 24 workers. Should I only be using 16 workers? Any help is greatly appreciated.

Jeff

rezilient

hero member

Activity: 574

Merit: 500

I have a customer who's getting the following Cgminer API error on his 230G Avalon2 clone (by CCBMC).

[Firmware Version] => 20131110
cgminer: 176747f
cgminer-openwrt-packages: 0e12b1b
luci: 346e3e7
Socket connect failed: Connection refused

He has confirmed the following for me:

- using pool stratum.btcguild.com:3333
- configuration page looks good, no typos
- API Allow is correctly set to "W:127.0.0.1"
- he can ping out to stratum.btcguild.com and IP resolves correctly
- "cgminer" process is not currently running when we check Processes tab
- he has tried many other pools aside from btcguild with no luck

Any idea what the problem might be? I tested the device before shipping and it was working fine.

Thanks for any help. I have been reading that updating the firmware might help, but I'm not sure where to get the firmware.

SolarSilver

legendary

Activity: 1112

Merit: 1000

Quote from: patnor1011 on January 23, 2014, 03:41:09 PM

Ok, when I set up laptop IP as you suggested to 192.168.1.1 and ping machine using machine IP it work, sending and receiving all 4 packets. Led on ethernet connector actually is blue and orange is flashing.

and if you pull the cable it stops working?

If 192.168.1.1 works for you, can you try with IE?

Quote

I am afraid that I have no idea how to use ssh to log into machine as root.

You need to install the ssh utility for Windows like PuTTY and see if you can connect

Just use user root and passwd just enter

that should give you a shell.

Better log out if you have no idea what to do next before you do any damage (although that is difficult with the read-only setup)

Topic: Avalon ASIC users thread - page 28. (Read 438575 times)