Topic: [Awesome Miner] - Powerful Windows GUI to manage and monitor up to 200000 miners - page 482. (Read 703148 times)

Hey Patrike

I'm trying to customize your software to display my portfolio / stats in one place via the Balance section of this software.
The builtin block explorer works for the coins loaded on that site.
Also, I've read the help section
http://www.awesomeminer.com/help/coinbalance.aspx

Now I'm trying to put the balance in for
Bitcoinz, ZenCash, Hush, CVC, PIVX 

I've googled some block explorer sites for these coins... but I want to add them to the Balance section.

I mean I have found specific websites for these coins that detail their working block explorers.

I was hoping for some guidance on how to setup the Balance section for these coins. (its not a matter and cut/paste the URL, heh, I've tried)

How are any of you programming the Balance section to display the wallet totals of the coins that you are mining?

Its a handy feature to have in this software and the stock/default (BTC/LTC) features/explorers work fine. I'm just looking how direction as to how to program more than the available BTC/LTC coins

Thanks

I am running 2 rigs with 4GB in each. Not sure about drive space, doubt if it uses much.

Is anyone successfully running AM using only 4GB of RAM? Currently, I'm using 8GB on all of my Rigs but no reason to do so if 4GB is enough...

Also, how much SSD space? I suspect I'm overkilling in that department as well...

Thank you.!

Thank you very much for your reply. I updated, and all seems to be working fine now.

Cheers and have a nice day

Would be great if you could add in a function to force refresh the state of a rig, rather than wait or restart the whole app to get the latest information. I usually have to wait 2-3 minutes to go from 'Service Offline' to Mining, just because we theres a delay in refresh times.

Thanks for your hardwork.

@patrike I have a few bugs:

 - when trying to update, it downloads the package, exits, it says upgrading, then half way it exits and the old version starts again. Currently runing 4.24
 - i enabled dead vga detection, with rule to reboot but it does nothing
 - if i set up a managed miner, with claymore settings of -wd 1 and -r 1, when i check the details and command line it's with -wd 1 -r -1

I am looking to get Awesome Miner

But i have a problem

It is not picking up my Graphics Cards
EVGA GTX 1060 6GB Mining Edition

I have updated my Drivers and still no luck

Any way I can get the software to pick up my cards?

Hey, does anybody offer service to set up AwesomeMiner? I have 7 x gtx1070 mining rig with AwesomeMiner Enterprise edition latest version on Windows 10. I need help with getting more algorythms working as Lyra and Nist5 stop working at some point so that AwesomeMiner doesn't restart them so I have to manually restart. So I have disabled all except Neo that is stable but not most profitable at all times. Would like to enable other algorithms, too. Also need help with other settings: setting up remote control, sms notifications, mobile app and generally want to speak throught all settings. Need training at least 3-4 hours asap but also in future to set up customers' machines. If you're interested then let me know your hourly rate and contact details. My Skype: kasparpalgi. Or WhatsApp +3725288846 or call +34603192336.

I tried adding my own ccminer into AwesomeMiner and failed miserably... How would one go about doing this? I went into Options -> Managed Software and play around with that GUI but there's no obvious way to specify the location of the new ccminer binaries nor a way to import them into AwesomeMiner...

Thanks!

There is quite outdated Excavator 1.1.4 for nvidia cards in AM, new version is 1.3.8a  - https://github.com/nicehash/excavator  and it is far more better for lyra2R2 and other algos than ccminer 2.2.3. I wanted to add it manually but no luck (Excavator started but just waiting for something..)

Thank you!

forgot, dstm's ZCash Cuda miner is up to Version 0.5.7 Awesome  shows it at 5.5 even after i use the up load tool the CMD screen For the miner says 5.7..

The update mining software Definitions says there is no new updates.. didn't say anything till now, was hoping you would catch it, hate bugging people for minor things.

Thank you, and please let me know if you need more information about my setup.

crackfoo said this yesterday to explain why many were seeing crazy profits from SHA-3 -

-----------------------------------------
keccak is changed it to match the other blake/sha algos with BTC per GH instead of MH.

https://github.com/tpruvot/yiimp/commit/6b6866048e2e5a1ab0fb373e0c65da296bb0556b

You'll need to update accordingly.
-----------------------------------------

An update to AM was issued soon after, just tell AM to download the new version and you will see a corrected profit figure.

Hi,

So I have been running AM for a week now. It was working great and all, but the last 2 days it says it is mining 340$ per day on some unspec SHA-3.

I joined z-pool and only that. My address is set up on there. But when I check my balance in the pool, I am geting 10 satoshi per day. I got an nvidia 1060 gtx.

Somebody knows where the problem is? Please help, thank you

Miningpoolhub results after about 12 hours at 137MH on Lyra2REv2 using Mona as the mined coin:

Result converted from Mona and the payout in BCH: $3.50.

So, that's two cards going for 12 hours, at 720W (I measured.) which means about 80 cents worth of electricity, for a profit of $2.80.

Quite on the other hand, the INDICATED profit from Awesome Miner is 14-28 dollars per day, which would be closer to 2 to 3 times what I'm actually seeing, as far as gross profit goes.

https://whattomine.com/coins/148-mona-lyra2rev2?utf8=%E2%9C%93&hr=137000&p=720&fee=0.0&cost=.07&hcost=0.0&commit=Calculate

According to Whattomine, I should be profiting $13.01. (per 24 hours, remember, the 3.50 gross was from 12 hours)

But, alas, I am not. I am not on the same continent as that, let alone the same ballpark.

I really am curious where all the profit is going. I know where it is NOT going.

Update: left it running all night, hoping for 24 hours of results.

Woke up this morning, Awesome Miner running full tilt as it was last night.

only 1.9 additional dollars or so in wallet.

Too bad. Their profits will be short-lived, but they seem to be the types that live for the fast buck.

Ah, it gets better. I checked settings and found that Original.as, the guy posting on reddit, somehow switched the mining over to this username on MPH, instead of mine to:

Originalas.GarbageMiner

So, beware the guy touting his free, easy-to-set-up is a hacker.

Evidently, he also is in league with MPH, because my funds are gone from MPH, also.

Sad, people. Sad.

Nothing I have done that has to do with Awesome Miner or with MPH has been anything but failure, fraud, and theft.

Every time I checked it on MPH, it was doing over 130MH. Miner was active all day on MPH.

Huh. Too bad.

While setting up my vega rigs to mine cryptonight based coins, i got so fed up with trying to get wattman and HBCC working with the blockchain drivers. just a buggy pile of mess. In the end i set up 2 commands to run before mining starts on them, using the devcon (MS windows deployment kit utility) to disable and re-enable the vegas (this resets hbcc somehow), and then OverdriveNTool (3rd party utility) to set the clocks, voltages, power levels and fanspeed for each card using a saved profile. i dont even have wattman installed, just the drivers and nothing else.

Whats silly is afterburner works fine with 10 GPUs, so clearly it's not a 8GPU limitation. It only crashes when you do 11+ GPU. Sounds like laziness or antipathy on Afterburner Dev's part, which is unfortunate.

When setting up a new rig, instead of Afterbuner, I've recently started using asus GPUTweak on all my rigs to set baseline power and fan profiles for 12 GPU rigs beforehand.

For managed miners, I then have in the execute additional commands section, "nvoc *coreclock* *memclock*" (3rd party utility) to set the core and memory clocks, and "nvidia-smi -pl *watts*" (nvidia utility) to set the power levels. It's not as easy as afterburner, but it is for sure more reliable. I do like that nvsmi takes wattage numbers for input instead of a % amount, which can vary depending on different cards TDP factory settings. Can't use this for profit miners at the moment unfortunately, i'm hoping something similar will be considered for them in the future.

That's the thing.  You don't tell AM to ignore the 2nd GPU, you have AM tell the mining software to igniore the 2nd GPU.  It's a lot easier with managed miners as you can specify the command line attributes either at the pool level or the managed miner level.  I like to put these at the pool level, so that you don't have to go and change the managed miner every time you want to change pools.  For instance, if I'm mining Zcoin, I put the "-a lyra2z" for ccminer to use that algorithm at the pool level.  This works better, as I don't have to remove the "-a lyra2z" at the managed miner level every time I want to change the pool on the managed miner.

For profit switching, this becomes a lot more difficult, as you can only ever select specific algorithms that use particular software that has the ability to skip or disable GPUs.  I know that Claymore's has this ability.  But honestly, this would be a pain to setup... and to what end?

As you mentioned, it would probably make more sense to just pull that 2nd GPU out.  Sometimes, the root cause of the problem is a simple fix, rather than trying to use software to mask over the root cause.

Can you point me in a direction where I would be able to find the info to figure out what command line parameters one would use for setting up profit switching?
More pressing... Short of pulling out my second way too old gpu ( being replaced. new one in transit ) How would I tell Awesome Miner to completely ignore the 2nd gpu?

don't forget the one that comes with AMD driver now.

Wattman

I'll learn how to use wattman .as much as l like using After burner it has issue with the new AMD driver still,  it only works with 3 cards anything over 3 the the fan and over clock section is grayed out they know about it and it seems there not fixing it, so i have to use the Radeon Software Crimson ReLive Edition Beta for Blockchain Compute from 8/23/2017 if i want to use more then three AMD cards in a rig with after burner it fine so far with any of a mount of Nv cards i have tried.. and i tried using After burner 4.4.2 beta no go with the new AND drivers .

ASUS tweak -ii it's a fork afterburner .
https://www.asus.com/us/site/graphics-cards/gpu-tweak-ii/

There is not really much to pick from.