i'm selling an antminer a3 if anybody is interested...
https://bitcointalksearch.org/topic/wts-antminer-a3-815ghs-blake2b-miner-sold-2822606
Topic: Bitmain just announced the AntMiner A3 - 815GH/s Siacoin miner - Blake(2b) - page 16. (Read 12766 times)
January 25, 2018, 01:26:21 PM
January 25, 2018, 01:20:11 PM
i got my A3 Today to, hoocked it up, got an ip but was not accesible. Without all Boards the A3 Webinterface comes up. I manged to get one Board Recognized. As soon as i connect more then that one Board the Webinterface is not accesable anymore and i cannot Ping the Device anymore.
Anyone has a Solution for that?
Can you enter your pool data whitout the hash boards, Save it and after that connect the hash boards and power on the Miner?Anyone has a Solution for that?
Did you restore the factory defaults with press the reset Button 10-15 seconds?
January 25, 2018, 01:16:06 PM
I know this has been asked a few times, but this thread is very long and hard to search.
1. What SIA Pools are people planing to mine and in what order? I ask mainly because of the SIA drama, supporting the fork via luxor etc. So what pools should I support with my A3?
-SiaMining.com
-nanopool.org ??
-
?
2. What are the settings used for the other pools. Siamining.com was easy enough to figure out.
1. What SIA Pools are people planing to mine and in what order? I ask mainly because of the SIA drama, supporting the fork via luxor etc. So what pools should I support with my A3?
-SiaMining.com
-nanopool.org ??
-
?2. What are the settings used for the other pools. Siamining.com was easy enough to figure out.
January 25, 2018, 01:10:56 PM
i got my A3 Today to, hoocked it up, got an ip but was not accesible. Without all Boards the A3 Webinterface comes up. I manged to get one Board Recognized. As soon as i connect more then that one Board the Webinterface is not accesable anymore and i cannot Ping the Device anymore.
Anyone has a Solution for that?
Anyone has a Solution for that?
January 25, 2018, 12:41:22 PM
If you ordered A3 via DHL, then how will you know if a customs fee is due, how do you pay it and how much?
I didnt order through DHL, but through UPS and found out that I owe a customs fee of 72 Bux... Ugh
I don't see your issue. I have a 20% VAT bill of £345
January 25, 2018, 12:39:05 PM
What I noticed overnight was that the S9's were all putting out about 2/3's their hash rate whereas previously they were fine, both A3's went down to almost nothing but were still hashing. Think the power draw was too high with all these machines, ended up unplugging an S9 and the other two evened out, A3's came back now putting out 1700 GH/s total for the longest period they've held yet. Possibly the reason why they only list 220 on their website... we're in the midst of having 3-phase 220 installed. Can't come soon enough!
January 25, 2018, 12:29:48 PM
If you ordered A3 via DHL, then how will you know if a customs fee is due, how do you pay it and how much?
I didnt order through DHL, but through UPS and found out that I owe a customs fee of 72 Bux... Ugh
January 25, 2018, 11:59:24 AM
Whuddup Vosk, huge fan of your channel been following for awhile.
My friend and I both ordered AntMiner A3's, we received both today and got them hooked up around 6:00pm EST. One has been running flawlessly up until a few minutes ago, the other is exhibiting the same issues others have mentioned. Fault light comes on, shows erratic hash rates, all hash boards and ASIC chips are recognized, temps are okay but it's clearly not getting any work done.
We were getting hashrates of about 1500-1700 (total for both units combined), then it was around 900 when we first noticed an issue with one of the miners. Unplugged it for about two minutes, plugged it back in and still received a fault light and low hash rates. Unplugged it and swapped rooms, PSUs and cables with a known good S9 and it started working again at full speed. About 15-20 minutes later the same thing started happening.
Troubleshooting these kinda sucks because we keep them across town. May end up bringing them home until they simmer down and straighten out.
About two hours later I'm getting the issue for the first time with the other miner, now down to 313 GH/s total... No bueno. If anyone comes up with a solution or reason why this is happening would love to hear it.
That’s awesome man thanks for the support! My friend and I both ordered AntMiner A3's, we received both today and got them hooked up around 6:00pm EST. One has been running flawlessly up until a few minutes ago, the other is exhibiting the same issues others have mentioned. Fault light comes on, shows erratic hash rates, all hash boards and ASIC chips are recognized, temps are okay but it's clearly not getting any work done.
We were getting hashrates of about 1500-1700 (total for both units combined), then it was around 900 when we first noticed an issue with one of the miners. Unplugged it for about two minutes, plugged it back in and still received a fault light and low hash rates. Unplugged it and swapped rooms, PSUs and cables with a known good S9 and it started working again at full speed. About 15-20 minutes later the same thing started happening.
Troubleshooting these kinda sucks because we keep them across town. May end up bringing them home until they simmer down and straighten out.
About two hours later I'm getting the issue for the first time with the other miner, now down to 313 GH/s total... No bueno. If anyone comes up with a solution or reason why this is happening would love to hear it.
Personally I just restarted it remotely twice and luckily it fixed itself
What pool are you on and what are temps and is it stock clocked?
Have same issue same with my two A3... Did all know procedures ( reboot, reset, plug/unplug PSU, wifi and no changes. Hope boards will comes back same way it disappeared
DO you know source to A3 firmware (version 1.3.0.
? This could work also... ATM have 800 GH/s on two --- f***g amazing, paid for two mining as one 
January 25, 2018, 09:19:04 AM
which pool are you mining?
please give me some advice, I have received just right now and can't go on.
thanks
please give me some advice, I have received just right now and can't go on.
thanks
January 25, 2018, 09:05:46 AM
Whuddup Vosk, huge fan of your channel been following for awhile.
My friend and I both ordered AntMiner A3's, we received both today and got them hooked up around 6:00pm EST. One has been running flawlessly up until a few minutes ago, the other is exhibiting the same issues others have mentioned. Fault light comes on, shows erratic hash rates, all hash boards and ASIC chips are recognized, temps are okay but it's clearly not getting any work done.
We were getting hashrates of about 1500-1700 (total for both units combined), then it was around 900 when we first noticed an issue with one of the miners. Unplugged it for about two minutes, plugged it back in and still received a fault light and low hash rates. Unplugged it and swapped rooms, PSUs and cables with a known good S9 and it started working again at full speed. About 15-20 minutes later the same thing started happening.
Troubleshooting these kinda sucks because we keep them across town. May end up bringing them home until they simmer down and straighten out.
About two hours later I'm getting the issue for the first time with the other miner, now down to 313 GH/s total... No bueno. If anyone comes up with a solution or reason why this is happening would love to hear it.
That’s awesome man thanks for the support! My friend and I both ordered AntMiner A3's, we received both today and got them hooked up around 6:00pm EST. One has been running flawlessly up until a few minutes ago, the other is exhibiting the same issues others have mentioned. Fault light comes on, shows erratic hash rates, all hash boards and ASIC chips are recognized, temps are okay but it's clearly not getting any work done.
We were getting hashrates of about 1500-1700 (total for both units combined), then it was around 900 when we first noticed an issue with one of the miners. Unplugged it for about two minutes, plugged it back in and still received a fault light and low hash rates. Unplugged it and swapped rooms, PSUs and cables with a known good S9 and it started working again at full speed. About 15-20 minutes later the same thing started happening.
Troubleshooting these kinda sucks because we keep them across town. May end up bringing them home until they simmer down and straighten out.
About two hours later I'm getting the issue for the first time with the other miner, now down to 313 GH/s total... No bueno. If anyone comes up with a solution or reason why this is happening would love to hear it.
Personally I just restarted it remotely twice and luckily it fixed itself
What pool are you on and what are temps and is it stock clocked?
January 25, 2018, 08:41:01 AM
This coins difficulty is going up higher than the ETH difficulty even
Those who haven't received their ASIC yet must be really feeling it every 30 mins that the difficulty adjusts higher and higher.
Those who haven't received their ASIC yet must be really feeling it every 30 mins that the difficulty adjusts higher and higher.
It adjusts 0.40% every block. So it will take a while to adjust up to a fair difficulty.
Fun fact: Out of the 15,000+ A3's that Bitmain sold last week, only ~1,700 are currently mining.
any proof link to 15k A3 sold by Bitmain?
a lot of assumptions here on sold amount, but not a single has a trustable source...
January 25, 2018, 06:57:31 AM
What Temp do you guys have....
January 25, 2018, 01:22:05 AM
This coins difficulty is going up higher than the ETH difficulty even
Those who haven't received their ASIC yet must be really feeling it every 30 mins that the difficulty adjusts higher and higher.
Those who haven't received their ASIC yet must be really feeling it every 30 mins that the difficulty adjusts higher and higher.
It adjusts 0.40% every block. So it will take a while to adjust up to a fair difficulty.
Fun fact: Out of the 15,000+ A3's that Bitmain sold last week, only ~1,700 are currently mining.
any proof link to 15k A3 sold by Bitmain?
a lot of assumptions here on sold amount, but not a single has a trustable source...
Trustable sources aren't required. They can just say whatever they want. That's how this game works. Watch.
OMG OBELISK IS GOING TO DESTROY DECRED! THEY ARE ATTACKING ALL THEIR COMPETITION. FIRST THEY FORKED SIACOIN TO DESTROY THE BITMAIN A3 NOW THEY WANT TO DESTROY DECRED WITH THEIR DCR1 MINER!!!!!! CAREFUL EVERYONE THEY ARE GOING TO 51% ATTACK DECRED! WE SHOULD SOFT FORK DECRED TO PREVENT THE MALICIOUS EVIL OBELISK MINERS FROM HAVING CENTRALIZED DECRED CONTROL! THEY USED ALL THEIR BTC FROM PREORDER TO SLOWLY BUY TOKEN FOR VOTING! THEY NOW CONTROL THE DECRED NETWORK!
January 25, 2018, 01:19:20 AM
Whuddup Vosk, huge fan of your channel been following for awhile.
My friend and I both ordered AntMiner A3's, we received both today and got them hooked up around 6:00pm EST. One has been running flawlessly up until a few minutes ago, the other is exhibiting the same issues others have mentioned. Fault light comes on, shows erratic hash rates, all hash boards and ASIC chips are recognized, temps are okay but it's clearly not getting any work done.
We were getting hashrates of about 1500-1700 (total for both units combined), then it was around 900 when we first noticed an issue with one of the miners. Unplugged it for about two minutes, plugged it back in and still received a fault light and low hash rates. Unplugged it and swapped rooms, PSUs and cables with a known good S9 and it started working again at full speed. About 15-20 minutes later the same thing started happening.
Troubleshooting these kinda sucks because we keep them across town. May end up bringing them home until they simmer down and straighten out.
About two hours later I'm getting the issue for the first time with the other miner, now down to 313 GH/s total... No bueno. If anyone comes up with a solution or reason why this is happening would love to hear it.
My friend and I both ordered AntMiner A3's, we received both today and got them hooked up around 6:00pm EST. One has been running flawlessly up until a few minutes ago, the other is exhibiting the same issues others have mentioned. Fault light comes on, shows erratic hash rates, all hash boards and ASIC chips are recognized, temps are okay but it's clearly not getting any work done.
We were getting hashrates of about 1500-1700 (total for both units combined), then it was around 900 when we first noticed an issue with one of the miners. Unplugged it for about two minutes, plugged it back in and still received a fault light and low hash rates. Unplugged it and swapped rooms, PSUs and cables with a known good S9 and it started working again at full speed. About 15-20 minutes later the same thing started happening.
Troubleshooting these kinda sucks because we keep them across town. May end up bringing them home until they simmer down and straighten out.
About two hours later I'm getting the issue for the first time with the other miner, now down to 313 GH/s total... No bueno. If anyone comes up with a solution or reason why this is happening would love to hear it.
January 24, 2018, 11:28:30 PM
Which block explorer are you using? I can't get Sia block explorer to work.
https://explorer.siahub.info/hash/6b633a9030fc44f723ebd64113347407297df78b695872d52d1b9aba469ed0c8
Working for me now. It had an error earlier.
Overall I'm impressed with siamining site considering all the new traffic they are getting.
Just the deposits to exchanges are slow but that is probably exchanges fault.
January 24, 2018, 11:27:04 PM
If you ordered A3 via DHL, then how will you know if a customs fee is due, how do you pay it and how much?
that depends on your country's customs rates for such devices January 24, 2018, 11:14:10 PM
If you ordered A3 via DHL, then how will you know if a customs fee is due, how do you pay it and how much?
January 24, 2018, 11:12:49 PM
This coins difficulty is going up higher than the ETH difficulty even
Those who haven't received their ASIC yet must be really feeling it every 30 mins that the difficulty adjusts higher and higher.
Those who haven't received their ASIC yet must be really feeling it every 30 mins that the difficulty adjusts higher and higher.
It adjusts 0.40% every block. So it will take a while to adjust up to a fair difficulty.
Fun fact: Out of the 15,000+ A3's that Bitmain sold last week, only ~1,700 are currently mining.
any proof link to 15k A3 sold by Bitmain?
a lot of assumptions here on sold amount, but not a single has a trustable source...
January 24, 2018, 11:11:42 PM
Support me on the decred redit. Let's push the decred community to soft fork to defend itself against the obelisk dcr1 miner. The SIA development team have proven themselves untrustworthy. Who knows what they will do with all that decred asic hardware?! They will probably 51% attack the network! I heard that they sold 1 million miners!
https://www.reddit.com/r/decred/comments/7st4fw/obelisk_51_attack_is_coming/
OMG, and here I was thinking your banner was funny. One MILLION OBELISK MINERS SOLD???! You, sir, are clearly a shill for Bitmain, or off your meds, or your sense of satire is sublime. Pick any two.
January 24, 2018, 11:07:47 PM
This coins difficulty is going up higher than the ETH difficulty even
https://siamining.com/stats
compared to
https://etherscan.io/chart/hashrate
Those who haven't received their ASIC yet must be really feeling it every 30 mins that the difficulty adjusts higher and higher.
https://siamining.com/stats
compared to
https://etherscan.io/chart/hashrate
Those who haven't received their ASIC yet must be really feeling it every 30 mins that the difficulty adjusts higher and higher.
Yes, yes indeed. It is torture.
Jump to: