[Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s) - page 111.

R0mi

full member

Activity: 305

Merit: 148

Theranos Coin - IoT + micro-blood arrays = Moon!

Quote from: VegaMiner on December 07, 2017, 09:04:35 PM

I'm having the "one card drops to 0 h/s" issue too. I get that error then the whole rig stops hashing with the GPUs even though XMR still shows activity. Eventually the system crashes when i try to quit the miner and I have to reboot. It happens after 45-60 mins of mining almost every time. I'm going to reinstall windows again but this issue is making me rethink my XMR mining. I might end up ditching this project and going with asics if I cant get it working. Has anyone solved it?

Sigh. Vegamining blog for a script that you can modify to monitor hash rate and restart. If the same card keeps dropping to "0" dial back the P7 and P3 settings using OverDriveNTool and apply that profile to just the weak card.

k9dom

newbie

Activity: 1

Merit: 0

Linux Version?

dagarair

sr. member

Activity: 847

Merit: 383

WOOT - got all 6 so far working. Thanks fellas i had some dumb crap going on. FYI Pagefile is 45G and it works like a champ on 6. 30-35 it crashed. 6 so far at 12K hash, tomorrow i go for the 7th!

VegaMiner

newbie

Activity: 11

Merit: 0

I'm having the "one card drops to 0 h/s" issue too. I get that error then the whole rig stops hashing with the GPUs even though XMR still shows activity. Eventually the system crashes when i try to quit the miner and I have to reboot. It happens after 45-60 mins of mining almost every time. I'm going to reinstall windows again but this issue is making me rethink my XMR mining. I might end up ditching this project and going with asics if I cant get it working. Has anyone solved it?

BitcoinsGreece

member

Activity: 163

Merit: 16

Quote from: BogdanCo on December 07, 2017, 04:36:50 PM

Quote from: dagarair on December 07, 2017, 07:45:40 AM

Man I am about to throw this damn vega rig against the wall. I'm not a rookie, I ahve built 100's of miners and actually have over 200 running right now but this vega, man it's testing my patience.

Biostar TB250+
8GB Ram
SSD
Windows 10 1704? Whatever the newest is
Blockchain drivers
1600 Watt titanum EVGa

All risers and equipment tested on 7 rx 580 cards and operate without flaws.

7 x MSI Vega 56

pull 580 cards out, add
1 vega - works good
2 vega - works good(disable HBCC whatever that setting is sorry paying from memory)
3 Vega - Pixalation and frozen

I can get system to see all 7 cards but cant get past 2 to work. Any idea what the hell? Thanks in advance guys!

Use the IGPU as a primary display and you will be fine....

Had exactly the same issue on my third vega, as above user said use igpu and everything will work fine.

(If you get an error with 3 cards on the mining software , you need to edit and add more virtual memory) .

commonorx

newbie

Activity: 99

Merit: 0

Quote from: sikotic on December 07, 2017, 07:30:41 AM

I still get the "Cannot find Compute Drivers" when they are the only drivers loaded and have been DDU'd. 4 Vega 64 not seeing potential... Sad

I am using the ASRock H110 Prod MB, the on board video is enabled, should it not be for this to work properly?

change the -CL from either 0 to 1 or 2.

BogdanCo

hero member

Activity: 729

Merit: 513

Quote from: dagarair on December 07, 2017, 07:45:40 AM

Man I am about to throw this damn vega rig against the wall. I'm not a rookie, I ahve built 100's of miners and actually have over 200 running right now but this vega, man it's testing my patience.

Biostar TB250+
8GB Ram
SSD
Windows 10 1704? Whatever the newest is
Blockchain drivers
1600 Watt titanum EVGa

All risers and equipment tested on 7 rx 580 cards and operate without flaws.

7 x MSI Vega 56

pull 580 cards out, add
1 vega - works good
2 vega - works good(disable HBCC whatever that setting is sorry paying from memory)
3 Vega - Pixalation and frozen

I can get system to see all 7 cards but cant get past 2 to work. Any idea what the hell? Thanks in advance guys!

Use the IGPU as a primary display and you will be fine....

Morgon

member

Activity: 75

Merit: 10

Quote from: dagarair on December 07, 2017, 07:45:40 AM

Biostar TB250+

If my recent experience with this board is any indication, you might want to verify that Windows Event Viewer isn't throwing a ton of PCIe Bus errors

xeridea

sr. member

Activity: 449

Merit: 251

Quote from: dagarair on December 07, 2017, 07:45:40 AM

Man I am about to throw this damn vega rig against the wall. I'm not a rookie, I ahve built 100's of miners and actually have over 200 running right now but this vega, man it's testing my patience.

Biostar TB250+
8GB Ram
SSD
Windows 10 1704? Whatever the newest is
Blockchain drivers
1600 Watt titanum EVGa

All risers and equipment tested on 7 rx 580 cards and operate without flaws.

7 x MSI Vega 56

pull 580 cards out, add
1 vega - works good
2 vega - works good(disable HBCC whatever that setting is sorry paying from memory)
3 Vega - Pixalation and frozen

I can get system to see all 7 cards but cant get past 2 to work. Any idea what the hell? Thanks in advance guys!

Blockchain drivers enable Crossfire by default, which is near instant miner crash. If light on some cards is green, it means ULPS is active, which is a symptom of crossfire, but all read isn't guarantee its off either. Check CF every time adding cards. Can do up to 8 vegas just fine. Dont do HBCC, just disable/enable in device manager.

vessk0

newbie

Activity: 6

Merit: 0

How use Cast XMR with Mining Pool Hub?
I'm receiving this error

http://store.picbg.net/pubpic/17/06/feb0b83c15211706.PNG

Tried different ports with no success?

Code:

cast_xmr-vega -I 7 --opencl 1 -G 0,1 -S europe.cryptonight-hub.miningpoolhub.com:12024 -u my_btc_address.my_worker_name %*

Shnikes101

full member

Activity: 254

Merit: 109

Quote from: hozerdev on December 07, 2017, 10:56:47 AM

Each time I close the miner's console window it causes the system hang for a 1-2 seconds and somethims it might restart with blue win10 death screen. Win10 also shows the message in left bottom corner that the application hardware access was blocked. Anyone notice this?
Using ver 0.7

Pretty sure Cast has a quit function. Press q instead of just closing the window

rasimfb

newbie

Activity: 3

Merit: 0

Hello I am having this error with cast xmr : error cl_mem_object_allocation_failure calling clenqueuendrangekernel for kernel 0
I am mining with 4 amd rx vega 56
Can anyone help me about this ? ,
Thank you

https://i.hizliresim.com/rJoG91.jpg

hozerdev

newbie

Activity: 50

Merit: 0

Each time I close the miner's console window it causes the system hang for a 1-2 seconds and somethims it might restart with blue win10 death screen. Win10 also shows the message in left bottom corner that the application hardware access was blocked. Anyone notice this?
Using ver 0.7

thilan29

newbie

Activity: 37

Merit: 0

Quote from: R0mi on December 06, 2017, 04:31:46 PM

If your hash rate is dropping every few minutes, then your problem is with bad values for P7 and P3 (OverDriveNTool), or too aggressive settings in XMR-STAK config file.

What do you mean by "bad values"? I get hash speed drops within a couple of minutes on my Vegas.

Also, I cannot for the life of me get the powerplaysoftmod working for some reason. I noticed that the reg file spit out by OverdriveNTool was slightly different (different number of rows/columns) compared to the reg files posted in the Overclock.net thread. The files posted in the overclock thread allow me to boot into Windows but as soon as I try XMR, it crashes, but it works fine with Eth mining. The files spit out by OverdriveNTool more often than not causes Windows to not boot, so I have to boot into safe mode, load the stock reg file, then reboot, back to square one.

Anyone can provide me with some advice on what to try? I'm only doing this because OverdriveNTool is not allowing me to change voltages, only clocks. Running blockchain driver on a Vega 56 and 64, and currently using MSI Afterburner to change voltages since it actually works.

P00P135

full member

Activity: 1124

Merit: 136

Quote from: dagarair on December 07, 2017, 07:45:40 AM

Man I am about to throw this damn vega rig against the wall. I'm not a rookie, I ahve built 100's of miners and actually have over 200 running right now but this vega, man it's testing my patience.

Biostar TB250+
8GB Ram
SSD
Windows 10 1704? Whatever the newest is
Blockchain drivers
1600 Watt titanum EVGa

All risers and equipment tested on 7 rx 580 cards and operate without flaws.

7 x MSI Vega 56

pull 580 cards out, add
1 vega - works good
2 vega - works good(disable HBCC whatever that setting is sorry paying from memory)
3 Vega - Pixalation and frozen

I can get system to see all 7 cards but cant get past 2 to work. Any idea what the hell? Thanks in advance guys!

Make sure crossfire is disabled.

dagarair

sr. member

Activity: 847

Merit: 383

Man I am about to throw this damn vega rig against the wall. I'm not a rookie, I ahve built 100's of miners and actually have over 200 running right now but this vega, man it's testing my patience.

Biostar TB250+
8GB Ram
SSD
Windows 10 1704? Whatever the newest is
Blockchain drivers
1600 Watt titanum EVGa

All risers and equipment tested on 7 rx 580 cards and operate without flaws.

7 x MSI Vega 56

pull 580 cards out, add
1 vega - works good
2 vega - works good(disable HBCC whatever that setting is sorry paying from memory)
3 Vega - Pixalation and frozen

I can get system to see all 7 cards but cant get past 2 to work. Any idea what the hell? Thanks in advance guys!

sikotic

newbie

Activity: 4

Merit: 0

I still get the "Cannot find Compute Drivers" when they are the only drivers loaded and have been DDU'd. 4 Vega 64 not seeing potential... Sad

I am using the ASRock H110 Prod MB, the on board video is enabled, should it not be for this to work properly?

KhalidK

newbie

Activity: 6

Merit: 0

Hello guys,
I am getting frequent 0s, anyone know what the problem is?

https://i.gyazo.com/9d7a3299108f760e66e2a410b294b117.png

this is what ive got:

cast_xmr-vega --opencl 2 -G 0,1 -S xmr-eu2.nanopool.org:14444

underdog13

newbie

Activity: 12

Merit: 0

not sure what I could be doing different than others with only rx xxx cards but I ordered a couple vegas and was able to set them up 3830 avg and miner works fine but i've tried everything under the sun and on the rx only rig the miner runs about 8 times faster than the other, I have a much lower accepted shares percentage, pretty sure it's not reading the correct fan to gpu and spitting out more zero's than hashes. Never skips fan readout or temp. Getting 6600hs accross 8 cards but sometimes as high as 20 percent job outdated. Restart and 10, Best i've had it is now showing 92 percent accepted. Seriously considering putting 1 vega to 4 rx and see if that make miner slow down and get the 96 percent accepted on both. Open to any suggestions. tried with many different bat file combo

cast_xmr-vega -S xmr-us-east1.nanopool.org:14444 -u 463t2f679b48ec912eb5a2e156fbca.Hash/[email protected] -G 0,1,2,3,4,5,6,7 -I 9

beastykato

newbie

Activity: 7

Merit: 0

Quote from: beastykato on December 06, 2017, 07:24:07 PM

Hey guys, I've been mining to the nicehash pool and obviously because of the recent events I'm unable to do so.

So, I'm in a big learning phase here. I've got to use exchanges and new pools since before Nicehash handled all of that for me and simply sent me BTC.

I tried using the supernova pool addresses and sometimes they connect but then I get a "socket error" and it disconnects.

That pool address was: xmr-eu.suprnova.cc:5222. They have a couple others I tried as well that all failed.

Can any of you share some of your working pools?

Also, I intend to mine to mymonero.com online wallet. I assume it's very similar to myetherwallet? I don't plan on leaving it there long, but then using shapeshift.io to convert it every so often to BTC and then to my Ledger S.

I'm definitely unfamiliar with this process after being on easy street with Nicehash. Any help or recommendations are appreciated!

Ok, so I went ahead and did a little research on my own. I am on supportxmr.com using their pool and I got it working in CastXMR and my Vega's are all back to full speed.

Is anyone familiar with this pool and whether it's any good?

First thing I'm noticing is that I'm getting ~6300H/s on 3 Vegas and their online stat tracker is only showing 4230H/s and the amount I'm owed isn't registering at all either, it's still at 0. I'm gonna let it go because it's only been a little while, but would definitely like some input.

Topic: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s) - page 111. (Read 206404 times)