CCminer(SP-MOD) Modded NVIDIA Maxwell / Pascal kernels. - page 571.

sp_

legendary

Activity: 2954

Merit: 1087

Team Black developer

Quote from: rednoW on September 13, 2016, 03:39:30 AM

boost mem clock NVAPI not supported (((

You can change the memclock when the gpu is in p2 state mode. Or mod the bios.

more info here:

http://cryptomining-blog.com/7341-how-to-squeeze-some-extra-performance-mining-ethereum-on-nvidia/

Here they set the memclock higher, but we want to set it lower.

rednoW

legendary

Activity: 1510

Merit: 1003

Quote from: maxim000 on September 13, 2016, 02:53:52 AM

frequency and power limit possible to set in .bat file

4x1070 example:
ccminer_LBRY_priv3 -i 27 -c LBRY.conf --mem-clock=3299,3299,3299,3299 --gpu-clock=1949,1949,1949,1949 --plimit=85,85,85,85 --tlimit=77,77,77,77

boost mem clock NVAPI not supported (((
please, can you give me a command line for nvidia-smi to low mem clock.

I tried nvidia-smi -ac 810,2037
which is in list of possible clocks but it didn't change anything.
And yes, I tried to restart miner.

sp_

legendary

Activity: 2954

Merit: 1087

Team Black developer

Quote from: maxim000 on September 13, 2016, 02:53:52 AM

frequency and power limit possible to set in .bat file

4x1070 example:
ccminer_LBRY_priv3 -i 27 -c LBRY.conf --mem-clock=3299,3299,3299,3299 --gpu-clock=1949,1949,1949,1949 --plimit=85,85,85,85 --tlimit=77,77,77,77

But then you have to run ccminer with admin rights.

maxim000

full member

Activity: 304

Merit: 100

frequency and power limit possible to set in .bat file

4x1070 example:
ccminer_LBRY_priv3 -i 27 -c LBRY.conf --mem-clock=3299,3299,3299,3299 --gpu-clock=1949,1949,1949,1949 --plimit=85,85,85,85 --tlimit=77,77,77,77

rednoW

legendary

Activity: 1510

Merit: 1003

Quote from: sp_ on September 13, 2016, 01:03:21 AM

Nvidi-smi tool. You need to list the supported clocks first.

Ok, I'll give it a try. Now I use Palit ThunderMaster, it can downclock-1000 only

sp_

legendary

Activity: 2954

Merit: 1087

Team Black developer

Nvidi-smi tool. You need to list the supported clocks first.

thesmokingman

full member

Activity: 212

Merit: 100

Quote from: rednoW on September 13, 2016, 12:37:07 AM

Quote from: sp_ on September 13, 2016, 12:28:35 AM

Reduce the memclock as much as possible. 850mhz instead of 4000. And save some power.
My kernel isn't using any memory.

what tool did you use to low memory freq? nv_smi? nvidia_inspector?

I use Afterburner 4.3.0 Beta as it works with Pascal cards. -502 is the most AFB will allow me to clock the memory down without a BIOS mod and things are still running just fine...

rednoW

legendary

Activity: 1510

Merit: 1003

Quote from: sp_ on September 13, 2016, 12:28:35 AM

Reduce the memclock as much as possible. 850mhz instead of 4000. And save some power.
My kernel isn't using any memory.

what tool did you use to low memory freq? nv_smi? nvidia_inspector?

sp_

legendary

Activity: 2954

Merit: 1087

Team Black developer

Quote from: reb0rn21 on September 12, 2016, 06:42:44 PM

Quote from: thesmokingman on September 11, 2016, 11:57:33 PM

Gigabyte G1 Gaming GTX1070 *6(8pin)
drivers: 372.54
ccminer1.8.0 ~1544M(~257M) temp:59C power:1140W via NVIDIA-SMI (nvidia-smi -ac 4004,1999 & nvidia-smi -pl 190 / Core +150)
SP-MOD#3 ~1800M(~300M) temp:59C power:1090W via NVIDIA-SMI (nvidia-smi -ac 4004,1999 & nvidia-smi -pl 190 / Core +150)

~15% increase

ccminer1.8.1 crashes my system using the same command used below for ccminer 1.8.0 and SP-MOD#3

Command used to achieve the above rates:

ccminer1.8.0 - ccminer-x64.exe -t 6 -a lbry -o stratum+tcp://lbry.pool.mn:8878 -u XXXX -p XXXX --show-diff --cpu-priority 4
SP-MOD#3 - ccminer.exe -t 6 -a lbry -o stratum+tcp://lbry.pool.mn:8878 -u XXXX -p XXXX --show-diff --cpu-priority 4

I use almost the same speed with my rigs but with 22% less power usage and same speed, is it you bad config I don`t know

With SP mod if you got 300mhs with 1090w usage that is gr8, but you ccminer 1.8 results are just terrible

Reduce the memclock as much as possible. 850mhz instead of 4000. And save some power.
My kernel isn't using any memory.

sp_

legendary

Activity: 2954

Merit: 1087

Team Black developer

Did version #2 work bether with MRR? 2 minute donation instead of 4.

go6ooo1212

legendary

Activity: 1512

Merit: 1000

quarkchain.io

I haven't tryed it to MRR either , and I can't say much in that case.

scryptr

legendary

Activity: 1797

Merit: 1028

Quote from: bensam1231 on September 12, 2016, 06:35:12 PM

Guessing Nik bought it from Scrypt... He isn't responding because you didn't buy it from him.

CCminer has a bug with MRR, you have to use the dynamic port it tries to reconnect to as it doesn't tolerate stratum redirection for some reason. Epsylons version has this bug as well.

Still saying SP you should lower fee to 2% and it should be a free release.

HAVE NOT TRIED SP_ #3--

I don't have a copy to sell. If what Nikolaj says is true, at least the way I read it, sp_ 's #3 is not behaving as expected with MiningRigRentals. Actually, someone renting hash through a fee based miner is probably getting skinned 2 times. I like NiceHash because it is so easy, but as I did more math, I appreciate a pool like Epsylon3's more and more. Never hooked-up to MiningRigRentals. Don't have a real opinion there.

As for the basic "WTF IS GOING ON HERE?", I take it that the miner restarts the fee cycle with each reconnect, and never mines for Nikolaj. Just guessing.

As much as I've supported sp_ with 0.1 BTC in the past, it used to mean $20-$25. The upfront fee is too steep for me just now. --scryptr

reb0rn21

legendary

Activity: 1901

Merit: 1024

Quote from: thesmokingman on September 11, 2016, 11:57:33 PM

Gigabyte G1 Gaming GTX1070 *6(8pin)
drivers: 372.54
ccminer1.8.0 ~1544M(~257M) temp:59C power:1140W via NVIDIA-SMI (nvidia-smi -ac 4004,1999 & nvidia-smi -pl 190 / Core +150)
SP-MOD#3 ~1800M(~300M) temp:59C power:1090W via NVIDIA-SMI (nvidia-smi -ac 4004,1999 & nvidia-smi -pl 190 / Core +150)

~15% increase

ccminer1.8.1 crashes my system using the same command used below for ccminer 1.8.0 and SP-MOD#3

Command used to achieve the above rates:

ccminer1.8.0 - ccminer-x64.exe -t 6 -a lbry -o stratum+tcp://lbry.pool.mn:8878 -u XXXX -p XXXX --show-diff --cpu-priority 4
SP-MOD#3 - ccminer.exe -t 6 -a lbry -o stratum+tcp://lbry.pool.mn:8878 -u XXXX -p XXXX --show-diff --cpu-priority 4

I use almost the same speed with my rigs but with 22% less power usage and same speed, is it you bad config I don`t know

With SP mod if you got 300mhs with 1090w usage that is gr8, but you ccminer 1.8 results are just terrible

bensam1231

legendary

Activity: 1764

Merit: 1024

Guessing Nik bought it from Scrypt... He isn't responding because you didn't buy it from him.

CCminer has a bug with MRR, you have to use the dynamic port it tries to reconnect to as it doesn't tolerate stratum redirection for some reason. Epsylons version has this bug as well.

Still saying SP you should lower fee to 2% and it should be a free release.

Nikolaj

sr. member

Activity: 445

Merit: 255

Quote from: Nikolaj on September 12, 2016, 03:23:33 PM

"Does any one of you experience a weird stratum reonnection with sp- 's latest v #3 LBRY kernel?"

Courtesy of scryptr Grin

On miningrigrentals it's almost a constant (!!!!) "donation" ! This fee miner it's a pain, this isn't the way to go.

@sp: 2 emails and a public notification. I am awaiting a response. thanks !

@ go6ooo1212
have you ever tried to point this release to Miningrigrentals? This kernel behaves weirdly, it constantly show a stratum reconnection, and given the fact that sp forces you to "donate" to him the first 4 minutes, you're donating with a 100% rate. In all honesty I've necer seen something like this from a fee-kernel, and I'm a bit worried.

@scryptr
hehe, thanks for your correct interpretation. Just edited the post with your phrase.

It's not that I'm expecting more, it's that I am expecting to mine for myself at 96.7% rate and 3.3% to sp, not 100% to him. Give it a try.

I've sent him an email some days ago regarding this issue and other things, still no response.

scryptr

legendary

Activity: 1797

Merit: 1028

Quote from: go6ooo1212 on September 12, 2016, 03:48:34 PM

Quote from: Nikolaj on September 12, 2016, 03:23:33 PM

do someone of you experience weird stratum reconnection with the latest sp lbry 3 kernel?

On miningrigrentals it's almost a constant (!!!!) "donation" ! This fee miner it's a pain, this isn't the way to go.

@sp: 2 emails and a public notification. I am awaiting a response. thanks !

Hello , mate. Sorry , but I didn't understand what exactly do you mean

POSSIBLE TRANSLATION--

"Does any one of you experience a weird stratum reonnection with sp- 's latest v #3 LBRY kernel?"

My best guess is that this release is not performing to Nikolaj's expectations. --scryptr

go6ooo1212

legendary

Activity: 1512

Merit: 1000

quarkchain.io

Quote from: Nikolaj on September 12, 2016, 03:23:33 PM

do someone of you experience weird stratum reconnection with the latest sp lbry 3 kernel?

On miningrigrentals it's almost a constant (!!!!) "donation" ! This fee miner it's a pain, this isn't the way to go.

@sp: 2 emails and a public notification. I am awaiting a response. thanks !

Hello , mate. Sorry , but I didn't understand what exactly do you mean

Nikolaj

sr. member

Activity: 445

Merit: 255

"Does any one of you experience a weird stratum reonnection with sp- 's latest v #3 LBRY kernel?"

Courtesy of scryptr Grin

On miningrigrentals it's almost a constant (!!!!) "donation" ! This fee miner it's a pain, this isn't the way to go.

@sp: 2 emails and a public notification. I am awaiting a response. thanks !

giagge

legendary

Activity: 1134

Merit: 1001

Quote from: Epsylon3 on September 12, 2016, 11:17:06 AM

ccminer (mine) handle --plimit on all platforms, but windows x86 value is in percent (like afterburner)

In afterburner i have 50% for minimum value , i try set --plimit 45 on .bat ( windows 10 x64 ) but PL in ccminer set automatically on 50% ? .

Epsylon3

legendary

Activity: 1484

Merit: 1082

ccminer/cpuminer developer

ccminer (mine) handle --plimit on all platforms, but windows x86 value is in percent (like afterburner)

Topic: CCminer(SP-MOD) Modded NVIDIA Maxwell / Pascal kernels. - page 571. (Read 2347641 times)