Topic: CGMINER Windows build for TECHNOBIT's Boards (Read 22523 times)

Hi
why my Hex8A1 reject shares?

Little late BUT. I can no longer find that type build for the cgminer. Could  ANYBODY point me to a link or right direction to obtain the software needed to run the device (technobit HEX16a,b,c etc). Any Help Would Be Greatly Appreciated ...Thank You,
             
                 

Disclamer: This topic is only for Technobit Boards, for original cgminer support please visit: https://bitcointalksearch.org/topic/official-cgminer-mining-software-thread-for-linuxwinosxmipsarmr-pi-4110-28402

With the help of "farmdve" from the Bulgarian Bitcoin forum BitcoinBG.eu here it is, the windows build of cgminer supporting Technobit boards like HEX16A2, HEX16B/B2, HEX8A1 etc.

Step by Step guide:
Updated: 29.12.2014

1. Files to download:
Zadig: http://zadig.akeo.ie/downloads/zadig_2.1.0.exe
Cgminer: http://bitcoinbg.eu/tools/technobit/cgminer_technobit_win_0_4_1b.zip
Cgminer Dice Version - Latest: http://bitcoinbg.eu/tools/technobit/cgminer_technobit_win_0_4_1_DICE.zip

EDIT 21.7.2017: Updated links for cgminer win https://mega.nz/#F!qIIXGbAY!VqmgqasZJz-FiYAMS5RDWQ

2. Connect the board don't install any drivers if asked


2.1. If you had installed previous com drivers from technobit the device will be recognized as COM port in device manager:

Leave it like this

3. Right Click on Zadig -> Run As Administrator

3.1. Go to Options and Check "List All Devices"

3.2. From the dropdown menu find the Technobit device connected


3.3. Click "Replace Driver", after installation finish click "Close"


3.4. Check if the driver is installed correctly, choose the board again from the dropdown menu, you should see something like this:


In device manager it is under Universal Serial Bus devices:

If you see this than your device is properly installed.

4. Extract the archive and just run cgminer.exe to test your installation

4.1 Edit cgminer.conf to suit your needs, the config file is with common settings for all supported devices.
you need Notepad++ to see linebreaks in cgminer.conf

5. Run cgminer.exe, if the board is not detected or you get some errors just replug it.

5.1 /not needed anymore/ In case that the board is still not recognized after replugging the usb cable, try edit the cgminer.conf field corresponding to your board:

change to


Here we go


This version is tested and runs on everything from Technobit except HEX16A, you can check my reviews of the boards for settings:
HEX16A2 (HEXc)
HEX16B (HEXb)
HEX16B2 BitFury2 (HEXb)
HEX8A1 260GH (HEX8)
HEX8A1 130GH (HEX8)
HEX4M 400GH (HEXM)
HEX4R - Spondoolies RokerBox
HEX16A4 - Avalon 4

Not tested with mixed boards.

Cgminer for !!! ONLY !!! HEX16A !!! ONLY !!!
1. Files to download:
Cgminer: http://bitcoinbg.eu/tools/cgminer_technobit_win/cgminer-hex16a.rar
You need to remove zadig for HEX16A boards

here is a screenshot:


best
2GOOD

New version available:
http://bitcoinbg.eu/tools/technobit/cgminer_technobit_win_0_4_1b.zip

Hello !

My Hex8A1 only rejected shares. Why ? Thank you answer ! http://kepfeltoltes.hu/view/141214/2014-12-14_21_41_23-cgminer_technobit_win_0_4_1b_www.kepfeltoltes.hu_.png

Can anyone recommend a Quality hub (12+prts) that will allow me to connect my 5 hex4m's together with my 4 hex8a1's and two hex16b's to my pc and and I will also want one to use it for the technobit openwrt router later since i'm building a 2nd setup in the shed. I am located in the EU so I would have to pay 21% vat on anything coming from the US but please I have tried many times  and failed spending several hundreds of euros in the process....

Can anyone recommend a Quality hub (12+prts) that will allow me to connect my 5 hex4m's together with my 4 hex8a1's and two hex16b's to my pc and and I will also want one to use it for the technobit openwrt router later since i'm building a 2nd setup in the shed. I am located in the EU so I would have to pay 21% vat on anything coming from the US but please I have tried many times  and failed spending several hundreds of euros in the process....

Anyone have details or a link to details about the correct conf file config for HEX4M boards? I am getting everything to fire up just fine with cgminer... but I'd like to play around with the power settings a bit and see what i can get out of the boards.

Hello 2Good,

I am currently running my six technobit hex16a2 at 1000MHz/ 850 mv.  Do you have any opinion about how much longer it would be still worth keeping these plugged in, before they are too unprofitable to run?