Claymore XPM GPU Miner discussion - page 45.

drmavis

member

Activity: 69

Merit: 10

Quote from: akuloff on April 16, 2014, 02:25:04 AM

Hello everyone,

Who mines on ypool - please try to move to another pool
I personally know only one else which works well with this miner: gpool.net (ip address for config in tutorial)

Pool monopoly is definately bad for the coin! Sad

btw, thanks for the miner, on my dual 7950 works well

Good call - gpool seems to work for me as well. I like that it has the lower 0.3 XPM payout threshold and only 2% fee. What port are you using? The tutorial makes it look like different ports are used for jhPrimeminer vs. xolo primeminer.

SpeedDemon13

hero member

Activity: 518

Merit: 500

I upgraded to Win 8.1 from Win 7 Ultimate found out that AMD Driver 14.3 crashes a lot in Win 8.1. So, just a pointer that 14.3 works ok on Win 7 but Win 8/8.1 works best with 13.12.

gilad215

full member

Activity: 430

Merit: 100

Quote from: MarcusDe on April 16, 2014, 05:18:47 PM

Quote from: incognitoworker on April 16, 2014, 01:01:51 PM

Quote from: gilad215 on April 16, 2014, 11:24:52 AM

Quote from: Claymore on April 16, 2014, 10:11:53 AM

Quote from: gilad215 on April 16, 2014, 09:09:10 AM

i have two rigs with same hardware and 5x280x

one has 2gb ram and the other 4gb ram

in the 2gb ram i can set hc512 and it works.

in the 4gb i can't even when its in the bat file, it works automaticly with 248 hashcnt. when i set gpu alloc100 the miner doesn't even start
trt400+-

the performance diffrence is so big between the two? will there be a fix?

Try to enable alloc100 and set "-hc 320".

can't enable GPU_MAX_ALLOC_PERCENT=100 with set, only setx works which makes me reinstall windows.
the cmd says variable enviorment not defiend

still hashct 248

Use it like this:set GPU_MAX_ALLOC_PERCENT=100
set makes the comand local, setx makes it permanent in registry.

You dont have to reinstall Windows, you can remove variable from registry, look in this thread.
set works with =
setx with

@Claymore:
Little success with stability on my rig:
10h without crash on 3 cards set -hc 512 and 1 card -hc 256 :-)

it works now with 320!

still trt the same numbers but it seems better for the long run thanks!

any fix for 512?

MarcusDe

hero member

Activity: 796

Merit: 505

Quote from: incognitoworker on April 16, 2014, 01:01:51 PM

Quote from: gilad215 on April 16, 2014, 11:24:52 AM

Quote from: Claymore on April 16, 2014, 10:11:53 AM

Quote from: gilad215 on April 16, 2014, 09:09:10 AM

i have two rigs with same hardware and 5x280x

one has 2gb ram and the other 4gb ram

in the 2gb ram i can set hc512 and it works.

in the 4gb i can't even when its in the bat file, it works automaticly with 248 hashcnt. when i set gpu alloc100 the miner doesn't even start
trt400+-

the performance diffrence is so big between the two? will there be a fix?

Try to enable alloc100 and set "-hc 320".

can't enable GPU_MAX_ALLOC_PERCENT=100 with set, only setx works which makes me reinstall windows.
the cmd says variable enviorment not defiend

still hashct 248

Use it like this:set GPU_MAX_ALLOC_PERCENT=100
set makes the comand local, setx makes it permanent in registry.

You dont have to reinstall Windows, you can remove variable from registry, look in this thread.
set works with =
setx with

@Claymore:
Little success with stability on my rig:
10h without crash on 3 cards set -hc 512 and 1 card -hc 256 :-)

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: f5inet on April 16, 2014, 01:37:31 PM

Does this miner support 7850 1G or 2G??

It should work if you specify "-hc 256" or may be some less value.

f5inet

member

Activity: 64

Merit: 10

Does this miner support 7850 1G or 2G??

incognitoworker

hero member

Activity: 736

Merit: 500

Quote from: gilad215 on April 16, 2014, 11:24:52 AM

Quote from: Claymore on April 16, 2014, 10:11:53 AM

Quote from: gilad215 on April 16, 2014, 09:09:10 AM

i have two rigs with same hardware and 5x280x

one has 2gb ram and the other 4gb ram

in the 2gb ram i can set hc512 and it works.

in the 4gb i can't even when its in the bat file, it works automaticly with 248 hashcnt. when i set gpu alloc100 the miner doesn't even start
trt400+-

the performance diffrence is so big between the two? will there be a fix?

Try to enable alloc100 and set "-hc 320".

can't enable GPU_MAX_ALLOC_PERCENT=100 with set, only setx works which makes me reinstall windows.
the cmd says variable enviorment not defiend

still hashct 248

Use it like this:set GPU_MAX_ALLOC_PERCENT=100
set makes the comand local, setx makes it permanent in registry.

gilad215

full member

Activity: 430

Merit: 100

Quote from: Claymore on April 16, 2014, 10:11:53 AM

Quote from: gilad215 on April 16, 2014, 09:09:10 AM

i have two rigs with same hardware and 5x280x

one has 2gb ram and the other 4gb ram

in the 2gb ram i can set hc512 and it works.

in the 4gb i can't even when its in the bat file, it works automaticly with 248 hashcnt. when i set gpu alloc100 the miner doesn't even start
trt400+-

the performance diffrence is so big between the two? will there be a fix?

Try to enable alloc100 and set "-hc 320".

can't enable gpu_max_alloc 100 with set, only setx works which makes me reinstall windows.
the cmd says variable enviorment not defiend

still hashct 248

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: qwep on April 16, 2014, 09:16:33 AM

When waiting for a new version of the miner Wink

In a few days, I'm working on further speedup.

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: gilad215 on April 16, 2014, 09:09:10 AM

i have two rigs with same hardware and 5x280x

one has 2gb ram and the other 4gb ram

in the 2gb ram i can set hc512 and it works.

in the 4gb i can't even when its in the bat file, it works automaticly with 248 hashcnt. when i set gpu alloc100 the miner doesn't even start
trt400+-

the performance diffrence is so big between the two? will there be a fix?

Try to enable alloc100 and set "-hc 320".

qwep

legendary

Activity: 1008

Merit: 1000

When waiting for a new version of the miner Wink

gilad215

full member

Activity: 430

Merit: 100

i have two rigs with same hardware and 5x280x

one has 2gb ram and the other 4gb ram

in the 2gb ram i can set hc512 and it works.

in the 4gb i can't even when its in the bat file, it works automaticly with 248 hashcnt. when i set gpu alloc100 the miner doesn't even start
trt400+-

the performance diffrence is so big between the two? will there be a fix?

hashfun

member

Activity: 117

Merit: 10

Quote from: Claymore on April 16, 2014, 01:23:11 AM

Quote from: hashfun on April 15, 2014, 05:08:49 PM

@Claymore

Total Round Time (TRT): 11795

If you get TRT = 0 or such big value, set "-hc 256" (see readme). Also make sure that Catalyst 13.12 is used, disabled overclocking and reboot computer.

Yes its working on New Version 2.1 set -hc256

Wed Apr 16 18:35:47 2014
New Block: 495264 - Current Diff: 10.733476
Total/Valid shares: [ 152 / 146 ] - Max diff: 10.167510
[ 4ch] [ 7ch] [ 8ch] [ 9ch] [ 10ch] [ 11ch] [ 12ch]
Total: [ 176665] [ 138] [ 12] [ 1] [ 1] [ 0] [ 0]
ch/h: [ 108588] [ 84.822] [ 7.376] [ 0.615] [ 0.615] [ 0.000] [ 0.000]
Estimated CPD: 1.4137, Average CPD: 14.7517
══════════════════════════════════════════════════════════════════════════════
Detailed stats mode disabled
04/16/14-18:36:04 - SHARE FOUND! DIFF:7.052511
══════════════════════════════════════════════════════════════════════════════
New Block: 495265 - Current Diff: 10.733523
Estimated CPD: 1.4177, Average CPD: 14.6873
══════════════════════════════════════════════════════════════════════════════
New Block: 495266 - Current Diff: 10.733552
Estimated CPD: 1.4143, Average CPD: 14.6513
══════════════════════════════════════════════════════════════════════════════
New Block: 495267 - Current Diff: 10.733571
Estimated CPD: 1.4071, Average CPD: 14.5768
══════════════════════════════════════════════════════════════════════════════
New Block: 495268 - Current Diff: 10.733620
Estimated CPD: 1.4039, Average CPD: 14.5440

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: WINNIE_POOL on April 16, 2014, 06:13:07 AM

Quote from: Claymore on April 16, 2014, 05:26:26 AM

Quote from: WINNIE_POOL on April 16, 2014, 05:06:45 AM

Hi Claymore,
I have many problem with many my grids: x 5 r9-270, x 6 r9-270, x 2 r9 - 270
When I run, I received 1 or 2 cards with stop driver VGA.
I use version 2.1, try with many config such as: ss - 2, HC: 512, 256 and default core, mem but still error. I can't fix it.
My command:
NsXpmMiner.exe -o ypool.net -u abcd.1 -p 1 -di 0 -ss 2 -sd 0 -hc 512
di 0-> 5
Ex: Card 0 stop driver, card 1 stop driver and no have TRT, CHD.

But no this error with other grid:5 x r9 280x or 5 x HD 7950.
Please see & resolve it for me.
Thanks

Try
NsXpmMiner.exe -o ypool.net -u abcd.1 -p 1 -di 0 -ss 2 -hc 256
Also try to remove "GPU_MAX_ALLOC_PERCENT" environment variable if you use it.
Also disable overclocking, install(reinstall) catalyst v13.12 and reboot computer. Helps in 99% cases.

Hi Claymore,
I remove GPU_MAX_ALLOC_PERCENT 100, restart pc and it's ok. I run 6 card 270 no problem.
But low speed.
GPU_MAX_ALLOC_PERCENT: TRT 680
Remove GPU_MAX_ALLOC_PERCENT: TRT 730

Can you fix this error and upgrade version 2.2 so that I still can use GPU_MAX_ALLOC_PERCENT 100 ?
Thanks

TRT 680 is ok for 270 cards. You can use GPU_MAX_ALLOC_PERCENT but use "-hc 256" or even less value (e.g. 200) that will work for you.

WINNIE_POOL

newbie

Activity: 53

Merit: 0

Quote from: Claymore on April 16, 2014, 05:26:26 AM

Quote from: WINNIE_POOL on April 16, 2014, 05:06:45 AM

Hi Claymore,
I have many problem with many my grids: x 5 r9-270, x 6 r9-270, x 2 r9 - 270
When I run, I received 1 or 2 cards with stop driver VGA.
I use version 2.1, try with many config such as: ss - 2, HC: 512, 256 and default core, mem but still error. I can't fix it.
My command:
NsXpmMiner.exe -o ypool.net -u abcd.1 -p 1 -di 0 -ss 2 -sd 0 -hc 512
di 0-> 5
Ex: Card 0 stop driver, card 1 stop driver and no have TRT, CHD.

But no this error with other grid:5 x r9 280x or 5 x HD 7950.
Please see & resolve it for me.
Thanks

Try
NsXpmMiner.exe -o ypool.net -u abcd.1 -p 1 -di 0 -ss 2 -hc 256
Also try to remove "GPU_MAX_ALLOC_PERCENT" environment variable if you use it.
Also disable overclocking, install(reinstall) catalyst v13.12 and reboot computer. Helps in 99% cases.

Hi Claymore,
I remove GPU_MAX_ALLOC_PERCENT 100, restart pc and it's ok. I run 6 card 270 no problem.
But low speed.
GPU_MAX_ALLOC_PERCENT: TRT 680
Remove GPU_MAX_ALLOC_PERCENT: TRT 730

Can you fix this error and upgrade version 2.2 so that I still can use GPU_MAX_ALLOC_PERCENT 100 ?
Thanks

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: WINNIE_POOL on April 16, 2014, 05:06:45 AM

Hi Claymore,
I have many problem with many my grids: x 5 r9-270, x 6 r9-270, x 2 r9 - 270
When I run, I received 1 or 2 cards with stop driver VGA.
I use version 2.1, try with many config such as: ss - 2, HC: 512, 256 and default core, mem but still error. I can't fix it.
My command:
NsXpmMiner.exe -o ypool.net -u abcd.1 -p 1 -di 0 -ss 2 -sd 0 -hc 512
di 0-> 5
Ex: Card 0 stop driver, card 1 stop driver and no have TRT, CHD.

But no this error with other grid:5 x r9 280x or 5 x HD 7950.
Please see & resolve it for me.
Thanks

Try
NsXpmMiner.exe -o ypool.net -u abcd.1 -p 1 -di 0 -ss 2 -hc 256
Also try to remove "GPU_MAX_ALLOC_PERCENT" environment variable if you use it.
Also disable overclocking, install(reinstall) catalyst v13.12 and reboot computer. Helps in 99% cases.

meocon966

newbie

Activity: 15

Merit: 0

Quote from: WINNIE_POOL on April 16, 2014, 05:06:45 AM

Hi Claymore,
I have many problem with many my grids: x 5 r9-270, x 6 r9-270, x 2 r9 - 270
When I run, I received 1 or 2 cards with stop driver VGA.
I use version 2.1, try with many config such as: ss - 2, HC: 512, 256 and default core, mem but still error. I can't fix it.
My command:
NsXpmMiner.exe -o ypool.net -u abcd.1 -p 1 -di 0 -ss 2 -sd 0 -hc 512
di 0-> 5
Ex: Card 0 stop driver, card 1 stop driver and no have TRT, CHD.

But no this error with other grid:5 x r9 280x or 5 x HD 7950.
Please see & resolve it for me.
Thanks

Hi, can you let me know TRT on HD 7950.
Thanks

WINNIE_POOL

newbie

Activity: 53

Merit: 0

Hi Claymore,
I have many problem with many my grids: x 5 r9-270, x 6 r9-270, x 2 r9 - 270
When I run, I received 1 or 2 cards with stop driver VGA.
I use version 2.1, try with many config such as: ss - 2, HC: 512, 256 and default core, mem but still error. I can't fix it.
My command:
NsXpmMiner.exe -o ypool.net -u abcd.1 -p 1 -di 0 -ss 2 -sd 0 -hc 512
di 0-> 5
Ex: Card 0 stop driver, card 1 stop driver and no have TRT, CHD.

But no this error with other grid:5 x r9 280x or 5 x HD 7950.
Please see & resolve it for me.
Thanks

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer