Topic: Claymore XPM GPU Miner discussion - page 47. (Read 142112 times)

Claymore

how to start a miner on 5770?
it is started, but the card falls

sanks

You will see estimated CPD immediately, however, you should wait about 30 minutes to get correct value. To get correct average CPD you need several days of mining.

Everyone that is giving stats like the 280x at 1.? cpd. Are these numbers from after about 24 hours of mining? Or should I see that within the first 30 mins of mining?

What about CPU load?

I was wrong, it's rounds.

This is from the pool directly: "Note that each block records the shares for the previous 160 rounds. A round is defined as the time between each block."

@Claymore:

I'm able to run my 4x280X rig without problems when i set 3 cards to hc=512 and last one with hc=256.
All cards get 110-115 4ch.
 

Try "NsXpmMiner.exe -o ypool.net -u YourLogin.WorkerName -p YourPassword -di 0 -hc 256 -ss 2"

When i do set set "GPU_MAX_ALLOC_PERCENT 100", it seems not mining at all.
Trt 0 and showing nothing in stats.
Could you plz post an exact bat config so i can see where i am putting it wrong?
Do i use the " before and after comand?
Not having bad results, but i see that it could be better compared to others.
8core cpu on most rigs, 2 gpus each.

Those are Chains per day

Does CPD equal to Coins per Day?

My 7950's Score 1.15 and 1.08 respectively, but my feeling is they produced much more... except if my R9 290 does all the work....

Hello people,

After few days of mining XPM here are my results

Machine 1:

Windows 7 Ultimate
Catalist 13.12
CPU: i5 3570k@ 4.4
GPU: 2 Sapphire 280x vapor-x @ 1144 mv / Core 1125 / Memory 1500 / Power Limit +10
Ram: 8 GB
BAT config:
setx GPU_MAX_ALLOC_PERCENT 100
NsXpmMiner.exe -o ypool.net -u x -p x -di 0 -ss 0
NsXpmMiner.exe -o ypool.net -u x -p x -di 1 -ss 0
══════════════════════════════════════════════════════════════════════════════
Total/Valid shares: [ 297 / 285 ]  -  Max diff: 9.924557
          [      4ch] [    7ch] [   8ch] [  9ch]  [   10ch] [   11ch] [   12ch]
 Total: [ 363014] [    266] [     29] [      2] [      0]   [        0] [      0]
  ch/h: [ 128661] [ 94.277][ 10.278][  0.709] [  0.000] [  0.000] [  0.000]
Estimated CPD:  1.5713, Average CPD:  0.0000
══════════════════════════════════════════════════════════════════════════════


Machine 2:
Windows 7 Ultimate
Catalist 13.12
CPU: Intel Pentium G6950
GPU: 2 Sapphire 280x vapor-x @ 1144 mv / Core 1125 / Memory 1500 / Power Limit +10
RAM: 4 GB
BAT Config:
setx GPU_MAX_ALLOC_PERCENT 100
NsXpmMiner.exe -o ypool.net -u x -p x -di 0 -ss 1
NsXpmMiner.exe -o ypool.net -u x -p x -di 1 -ss 1
══════════════════════════════════════════════════════════════════════════════
Total/Valid shares: [ 253 / 248 ]  -  Max diff: 10.368971
        [    4ch] [    7ch] [    8ch] [    9ch] [   10ch] [   11ch] [   12ch]
 Total: [ 310470] [    229] [     21] [      2] [      1] [      0] [      0]
  ch/h: [ 113239] [ 83.524] [  7.659] [  0.729] [  0.365] [  0.000] [  0.000]
Estimated CPD:  1.3921, Average CPD:  8.7536
══════════════════════════════════════════════════════════════════════════════

Hope That it helps.

Thanks again Claymore for this Beast Miner.

Always use default values. But if miner is unstable - try "-hc 256". It depends not only on card, but also how many GPUs you have installed. So just use default settings and change them only if you really need it.

Hi everyone,
I have a r9 270 card with 64k/h. Is it normal ?
Thanks 

What settings for 7870 people? -hc 256? -hc 384?

Not 160 Blocks, but 1000 : http://ypool.net/xpm/stats_blocks it's ca. 1 Day of mining.

Use "Claymore GPUs Control Utility v1.0" for overclocking and temperature control for all cards.

Claymore

whether it is possible to make the gpu-engine parameters and gpu-memclock in programm? because by default the program exposes 925 and 1300 and my card holds by default 1300 and 1550

sanks

If GPU does not allow to allocate enough memory, HashCnt will be decreased automatically, so even if 512 is specified you can see less value, set "GPU_MAX_ALLOC_PERCENT 100" to avoid it.
HC cannot be higher than 512, too much memory is required for higher values and OpenCL fails.

Takes 160 blocks to confirm each payment. So, it does take a while.

Q about ypool.

why do i have constantly all the time 30+- unconfirmed xpm's? does it takes longer than mining?

it will stay like this until the last day of my mining? so its like 30 coins are staying in the pool all the time it can stay like this for months.

captain?