I uploaded v11.2 for Linux.
rx550 not supported?
Topic: Claymore's CryptoNote AMD GPU Miner v11.3 - page 45. (Read 2145056 times)
rx550 not supported?
Finally have my 3x vega 64 rig running on 11.2 and windows
Only getting around 3050 H/s... Anyone have any ideas on why that may be? Haven't overclocked further than using the turbo setting in wattman
I'm getting a WATCHDOG: GPU 1 hangs in OpenCL call, exit
Then everything stops running I know Claymore said vega wasn't supported in linux that's why I was getting errors there but it's been working the past 2 days in windows.
Also I've set my virtual memory to 24gb since I'm running 3 8gb cards
Edit: according to my log it's happening on watchdog thread 5,6, and 7.
Only getting around 3050 H/s... Anyone have any ideas on why that may be? Haven't overclocked further than using the turbo setting in wattman
I'm getting a WATCHDOG: GPU 1 hangs in OpenCL call, exit
Then everything stops running I know Claymore said vega wasn't supported in linux that's why I was getting errors there but it's been working the past 2 days in windows.
Also I've set my virtual memory to 24gb since I'm running 3 8gb cards
Edit: according to my log it's happening on watchdog thread 5,6, and 7.
I've got Gigabyte RX570 cards, with Samsung memory. Trying to mod isn't working.
Once I change the Strap values the card is no long recognized by the sytem, even though it was working
fine beforehand. Blockchain drivers are installed and working, is there anything else I need to do?
Tried modding the card myself and also modding using https://anorak.tech/t/gigabyte-rx-570-aorus/34867 mods.
Neither worked.
Currently mining Monero at 770 H/s and trying to get up to 900.
TIA
Did you run https://www.monitortests.com/forum/Thread-AMD-ATI-Pixel-Clock-Patcher to remove BIOS signature check? Once I change the Strap values the card is no long recognized by the sytem, even though it was working
fine beforehand. Blockchain drivers are installed and working, is there anything else I need to do?
Tried modding the card myself and also modding using https://anorak.tech/t/gigabyte-rx-570-aorus/34867 mods.
Neither worked.
Currently mining Monero at 770 H/s and trying to get up to 900.
TIA
For best mining with Samsung, use Ubermix strap http://www.overclock.net/t/1604567/polaris-bios-editing-rx5xx-rx4xx and at least 1240MHz core. I use the 2.3 version less extreme. Some cards need slightly lower memclock for this mod. Speeds 970H+.
I uploaded v11.2 for Linux.
Were the issues with nicehash resolved?
I uploaded v11.2 for Linux.
I've got Gigabyte RX570 cards, with Samsung memory. Trying to mod isn't working.
Once I change the Strap values the card is no long recognized by the sytem, even though it was working
fine beforehand. Blockchain drivers are installed and working, is there anything else I need to do?
Tried modding the card myself and also modding using https://anorak.tech/t/gigabyte-rx-570-aorus/34867 mods.
Neither worked.
Currently mining Monero at 770 H/s and trying to get up to 900.
TIA
Once I change the Strap values the card is no long recognized by the sytem, even though it was working
fine beforehand. Blockchain drivers are installed and working, is there anything else I need to do?
Tried modding the card myself and also modding using https://anorak.tech/t/gigabyte-rx-570-aorus/34867 mods.
Neither worked.
Currently mining Monero at 770 H/s and trying to get up to 900.
TIA
upgraded to 11.2.
Still get a crash but not every time.
Performance increased by 100 H/s total for both rigs. Happy
Now if m pool would just pick up the pace a little. im on the etn spacepool.
what does the e-pool file do? I dont understand it
Read OP. Failover pools, or pool list (useful if using remote manager can easily switch pools...). Still get a crash but not every time.
Performance increased by 100 H/s total for both rigs. Happy
Now if m pool would just pick up the pace a little. im on the etn spacepool.
what does the e-pool file do? I dont understand it
upgraded to 11.2.
Still get a crash but not every time.
Performance increased by 100 H/s total for both rigs. Happy
Now if m pool would just pick up the pace a little. im on the etn spacepool.
what does the e-pool file do? I dont understand it
Still get a crash but not every time.
Performance increased by 100 H/s total for both rigs. Happy
Now if m pool would just pick up the pace a little. im on the etn spacepool.
what does the e-pool file do? I dont understand it
Mining ETN on Gigabyte RX480 4gb @ 1250/2170, hynix memory, custom straps.
Got about 870H/s on Claymore 10.2b with default settings (-h 900 -dmem 1).
Getting weird results on Claymore 11.2: default settings gives ~470H/s (-h 896 -dmem 1). After some fiddling with -h and -dmem got around 830H/s (-h 512 -dmem 1 or -h 1024 -dmem 0).
I'll stay with 10.2b for now. Too bad it can't mine devfee any more, but even with -nofee it is still a bit faster than 11.2.
Got about 870H/s on Claymore 10.2b with default settings (-h 900 -dmem 1).
Getting weird results on Claymore 11.2: default settings gives ~470H/s (-h 896 -dmem 1). After some fiddling with -h and -dmem got around 830H/s (-h 512 -dmem 1 or -h 1024 -dmem 0).
I'll stay with 10.2b for now. Too bad it can't mine devfee any more, but even with -nofee it is still a bit faster than 11.2.
Will switching to a newer version fix this?
Will i notice anything by switching to a new version?
Yes, change to the new version.
It will pay more and it is more stable. No more seeing locking when closing.
Been running 10.1 for just over a month now, and its awesome - I am making money, thank you dev team!
Just have a few questions to brush up on my knowledge if you guys dont mind:
where do these values go? i have not messed with them at all
GPU_FORCE_64BIT_PTR 1
GPU_MAX_HEAP_SIZE 100
GPU_USE_SYNC_OBJECTS 1
GPU_MAX_ALLOC_PERCENT 100
GPU_SINGLE_ALLOC_PERCENT 100
Also, I am experiencing a crash everytime i stop the miner, not a huge deal since its rare, but still an annoyance when i want to do maintenance.
Will switching to a newer version fix this?
Will i notice anything by switching to a new version?
running 2 rigs with x2 R9 290x's (blockchain driver) total hashrate is 3.34k H/s mining ETN
is it ok to post up a screenshot of my config and get some pointers?
Just have a few questions to brush up on my knowledge if you guys dont mind:
where do these values go? i have not messed with them at all
GPU_FORCE_64BIT_PTR 1
GPU_MAX_HEAP_SIZE 100
GPU_USE_SYNC_OBJECTS 1
GPU_MAX_ALLOC_PERCENT 100
GPU_SINGLE_ALLOC_PERCENT 100
Also, I am experiencing a crash everytime i stop the miner, not a huge deal since its rare, but still an annoyance when i want to do maintenance.
Will switching to a newer version fix this?
Will i notice anything by switching to a new version?
running 2 rigs with x2 R9 290x's (blockchain driver) total hashrate is 3.34k H/s mining ETN
is it ok to post up a screenshot of my config and get some pointers?
Put the GPU_*** values in the .bat file, see below, but I read somewhere (can't remember where) that, nowadays, these values make no difference to mining performance - I'm sure someone will correct me on this
Code:
setx GPU_FORCE_64BIT_PTR 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_SINGLE_ALLOC_PERCENT 100
setx GPU_MAX_ALLOC_PERCENT 100
NsGpuCNMiner -xpool stratum+tcp://pool.electroneum.space:3333 -xwal -xpsw x -allpools 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_SINGLE_ALLOC_PERCENT 100
setx GPU_MAX_ALLOC_PERCENT 100
NsGpuCNMiner -xpool stratum+tcp://pool.electroneum.space:3333 -xwal
2 rigs
x2 R9 290x OC @ 1070/1620 1700 H/s
x2 R9 290 OC @ 1070/1650 1650 H/s
here is my config:
==================================
-xpool stratum+tcp://pool.etn.spacepools.org:7777
-xwal My ETN wallt
-xpsw x
#-nofee 1
-allpools 1
#-tt 75
==================================
I feel like i should have a lot more in here to tweak things a bit
also, when you make a change do i have to close the miner and reopen or is there a refresh option in the miner? because when i close it, i get a crash and sometimes i have to jump through hoops to uninstall and reinstall the driver which takes an hour sometimes.
x2 R9 290x OC @ 1070/1620 1700 H/s
x2 R9 290 OC @ 1070/1650 1650 H/s
here is my config:
==================================
-xpool stratum+tcp://pool.etn.spacepools.org:7777
-xwal My ETN wallt
-xpsw x
#-nofee 1
-allpools 1
#-tt 75
==================================
I feel like i should have a lot more in here to tweak things a bit
also, when you make a change do i have to close the miner and reopen or is there a refresh option in the miner? because when i close it, i get a crash and sometimes i have to jump through hoops to uninstall and reinstall the driver which takes an hour sometimes.
soooo sweet ) that rx550 speed of yours...
https://imgur.com/a/SU8Iy
pls don't ask; i wont say a thing until claymore add support in v11;
after he make lexa work i will tell about it..... so pls keep presure on him
) that rx550 speed of yours...https://imgur.com/a/SU8Iy
pls don't ask; i wont say a thing until claymore add support in v11;
after he make lexa work i will tell about it..... so pls keep presure on him
I ever overclock this card before, and there is no 6 PIN addon power for it, I finally burn that card, fire and spark.
I dare not overclock it anymore.
Been running 10.1 for just over a month now, and its awesome - I am making money, thank you dev team!
Just have a few questions to brush up on my knowledge if you guys dont mind:
where do these values go? i have not messed with them at all
GPU_FORCE_64BIT_PTR 1
GPU_MAX_HEAP_SIZE 100
GPU_USE_SYNC_OBJECTS 1
GPU_MAX_ALLOC_PERCENT 100
GPU_SINGLE_ALLOC_PERCENT 100
Also, I am experiencing a crash everytime i stop the miner, not a huge deal since its rare, but still an annoyance when i want to do maintenance.
Will switching to a newer version fix this?
Will i notice anything by switching to a new version?
running 2 rigs with x2 R9 290x's (blockchain driver) total hashrate is 3.34k H/s mining ETN
is it ok to post up a screenshot of my config and get some pointers?
Just have a few questions to brush up on my knowledge if you guys dont mind:
where do these values go? i have not messed with them at all
GPU_FORCE_64BIT_PTR 1
GPU_MAX_HEAP_SIZE 100
GPU_USE_SYNC_OBJECTS 1
GPU_MAX_ALLOC_PERCENT 100
GPU_SINGLE_ALLOC_PERCENT 100
Also, I am experiencing a crash everytime i stop the miner, not a huge deal since its rare, but still an annoyance when i want to do maintenance.
Will switching to a newer version fix this?
Will i notice anything by switching to a new version?
running 2 rigs with x2 R9 290x's (blockchain driver) total hashrate is 3.34k H/s mining ETN
is it ok to post up a screenshot of my config and get some pointers?
soooo sweet ) that rx550 speed of yours...
https://imgur.com/a/SU8Iy
pls don't ask; i wont say a thing until claymore add support in v11;
after he make lexa work i will tell about it..... so pls keep presure on him
) that rx550 speed of yours...https://imgur.com/a/SU8Iy
pls don't ask; i wont say a thing until claymore add support in v11;
after he make lexa work i will tell about it..... so pls keep presure on him
anybody work with rx550 ddr5 4gb? working smoothly with rx580. but running rx550 hang on start claymore
I use sgminer 5.5.5-gm, 3x RX550 2GB, total 960H/s, no devfee.
stock setting without overclock / undervolt.
let me know what coin you minner with sgminer-gm?
i already using sgminer 5.5.5-gm to mining eth. its seem running slowly then claymore.
in sgm speed 7mh but claymore 10mh. but claymore hang on my rig
this thread is talking about cryptonight, and I am talking about mining cryptonight algo.
The coin I mine now is ETN (Electroneum), not ETH.
If you are using RX550, I suggest you try sgminer 5.5.5-gm, mining Electroneum,
or mine with NiceHack if you still trust NiceHack.
Try to tune to over 300H/s per card.
The following is the screenshot, GPU0 is onboard VGA being disabled, and GPU1-3 are RX550 2GB Saphhire pulse.
GPU 1 is 640 SP, so use 350.
GPU 2,3 are 512 SP, so use 280.
Each GPU config 2 threads.
If you are using 4GB version, I think you will not get much advantage over the 2GB version, not even more than 5% I think.
sgminer 5.5.5-gm-nicehash-8 - Started: [2018-01-08 13:39:19] - [0 days 01:46:33]
--------------------------------------------------------------------------------
(5s):916.7 (avg):947.1h/s | A:6580011 R:20000 HW:0 WU:7331.954/m
ST: 1 SS: 0 NB: 118 LW: 10171 GF: 0 RF: 0
Connected to *********** (stratum) diff as user *****
Block: 9f12d511... Diff:5.51G Started: [15:24:45] Best share: 35.4M
--------------------------------------------------------------------------------
[P]ool management [G]PU management (S)ettings [D]isplay options [Q]uit
GPU 0: 9.0C | OFF / 0.000h/s | R: 0.0% HW:0 WU: 0.000/m rI: 32
GPU 1: 51.0C 931RPM | 312.3/ 313.0h/s | R: 0.9% HW:0 WU:2553.692/m rI:350
GPU 2: 60.0C 964RPM | 316.8/ 317.5h/s | R: 0.0% HW:0 WU:2373.993/m rI:280
GPU 3: 71.0C 991RPM | 317.5/ 317.5h/s | R: 0.0% HW:0 WU:2448.977/m rI:280
--------------------------------------------------------------------------------
[15:23:27] Accepted 02bbdb01 Diff 24K/20K GPU 2
[15:23:56] Accepted 5021c5f0 Diff 209K/20K GPU 3
[15:23:59] Accepted 01b75a5f Diff 38.2K/20K GPU 1
[15:24:01] Accepted 026cc3f2 Diff 27K/20K GPU 3
[15:24:03] Accepted 16f362c7 Diff 731K/20K GPU 2
[15:24:11] Accepted 1f8c7900 Diff 532K/20K GPU 2
[15:24:27] Accepted 019cadd3 Diff 40.7K/20K GPU 1
[15:25:10] Accepted 031e6a98 Diff 21K/20K GPU 2
[15:25:19] Accepted 03374887 Diff 20.4K/20K GPU 3
[15:25:33] Accepted 02b7efa8 Diff 24.1K/20K GPU 3
[15:25:52] Accepted 02555c07 Diff 28.1K/20K GPU 3
I have a RX550 Rig with 6 Cards and use Claymore 9.7 and the hole System runs with 1875 H/s. Just use stock clockings and use -h 512 and each card runs over 300 H/s.
GPU 1: 52.0C 924RPM | 362.4/ 361.3h/s | R: 0.0% HW:0 WU:6.062/m rI:350 (640SP)
GPU 2: 64.0C 966RPM | 317.3/ 316.2h/s | R: 0.0% HW:0 WU:4.861/m rI:280 (512SP)
GPU 3: 72.0C 986RPM | 317.0/ 315.7h/s | R: 0.0% HW:0 WU:4.289/m rI:280 (512SP)
After some tuning, the 640SP card can do 360H/s.
I may buy 3 more (640SP) cards later on, just 72$ each.
Hope that I can ROI within 45 days.
Fixed the seg fault with NH?
I cannot see this bug (don't have it in Windows and don't have access to Linux system currently), but I found possible reason and fixed it. So need someone who sees this bug in Windows and can confirm that it is fixed in latest update. Or I will check it on Linux system directly in a few days.rx550 card dont work. ask missed asm and show 0 rate
True. rx550 does not work. Is there any possibility there gonna be asm support for `em? Cause with proper mem timings they give 500h/s w sgminer.
Hi Claymore.
I have a Rig with 6 ati Rx570 from saphire. I have been minning ethereum with you miner version 10.2 and it is working fine, but tried minning electroneum ( monero) with 10.2 and with the latest version and have a error... with version 9.7 mines ok, but is giving errors on the dev fee says it cant connect. But no crashes on the miner...
I have the folowing error:
GPU 1, GpuMiner dk2an0 failed -4
- this one randomly on all gpu 2 at a time, starts to mine and the the miner crashes and restarts.
Is says i am making 700 hs on each card ( 9.7 makes 620 about that...)
The cards only have the bios mod for eth ( the 1500 strap to above) They are stable on ethereum...
Claymore CryptoNote AMD GPU Miner v11.2 - POOL
This is my start.bat
NsGpuCNMiner.exe -xpool stratum+ssl://etn-eu1.nanopool.org:13433 -xwal my etnadress.RIG_ATI/myemail -xpsw x -allpools 1
Can you or any one help.
Best regards.
I have a Rig with 6 ati Rx570 from saphire. I have been minning ethereum with you miner version 10.2 and it is working fine, but tried minning electroneum ( monero) with 10.2 and with the latest version and have a error... with version 9.7 mines ok, but is giving errors on the dev fee says it cant connect. But no crashes on the miner...
I have the folowing error:
GPU 1, GpuMiner dk2an0 failed -4
- this one randomly on all gpu 2 at a time, starts to mine and the the miner crashes and restarts.
Is says i am making 700 hs on each card ( 9.7 makes 620 about that...)
The cards only have the bios mod for eth ( the 1500 strap to above) They are stable on ethereum...
Claymore CryptoNote AMD GPU Miner v11.2 - POOL
This is my start.bat
NsGpuCNMiner.exe -xpool stratum+ssl://etn-eu1.nanopool.org:13433 -xwal my etnadress.RIG_ATI/myemail -xpsw x -allpools 1
Can you or any one help.
Best regards.
To solve this problem increase the windows virtual memory.
8GB x 6 gpu = 48GB (free 50gb of virtual memory and will work without problems)
Fixed the seg fault with NH?
I cannot see this bug (don't have it in Windows and don't have access to Linux system currently), but I found possible reason and fixed it. So need someone who sees this bug in Windows and can confirm that it is fixed in latest update. Or I will check it on Linux system directly in a few days.rx550 card dont work. ask missed asm and show 0 rate
anybody work with rx550 ddr5 4gb? working smoothly with rx580. but running rx550 hang on start claymore
I use sgminer 5.5.5-gm, 3x RX550 2GB, total 960H/s, no devfee.
stock setting without overclock / undervolt.
let me know what coin you minner with sgminer-gm?
i already using sgminer 5.5.5-gm to mining eth. its seem running slowly then claymore.
in sgm speed 7mh but claymore 10mh. but claymore hang on my rig
this thread is talking about cryptonight, and I am talking about mining cryptonight algo.
The coin I mine now is ETN (Electroneum), not ETH.
If you are using RX550, I suggest you try sgminer 5.5.5-gm, mining Electroneum,
or mine with NiceHack if you still trust NiceHack.
Try to tune to over 300H/s per card.
The following is the screenshot, GPU0 is onboard VGA being disabled, and GPU1-3 are RX550 2GB Saphhire pulse.
GPU 1 is 640 SP, so use 350.
GPU 2,3 are 512 SP, so use 280.
Each GPU config 2 threads.
If you are using 4GB version, I think you will not get much advantage over the 2GB version, not even more than 5% I think.
sgminer 5.5.5-gm-nicehash-8 - Started: [2018-01-08 13:39:19] - [0 days 01:46:33]
--------------------------------------------------------------------------------
(5s):916.7 (avg):947.1h/s | A:6580011 R:20000 HW:0 WU:7331.954/m
ST: 1 SS: 0 NB: 118 LW: 10171 GF: 0 RF: 0
Connected to *********** (stratum) diff as user *****
Block: 9f12d511... Diff:5.51G Started: [15:24:45] Best share: 35.4M
--------------------------------------------------------------------------------
[P]ool management [G]PU management (S)ettings [D]isplay options [Q]uit
GPU 0: 9.0C | OFF / 0.000h/s | R: 0.0% HW:0 WU: 0.000/m rI: 32
GPU 1: 51.0C 931RPM | 312.3/ 313.0h/s | R: 0.9% HW:0 WU:2553.692/m rI:350
GPU 2: 60.0C 964RPM | 316.8/ 317.5h/s | R: 0.0% HW:0 WU:2373.993/m rI:280
GPU 3: 71.0C 991RPM | 317.5/ 317.5h/s | R: 0.0% HW:0 WU:2448.977/m rI:280
--------------------------------------------------------------------------------
[15:23:27] Accepted 02bbdb01 Diff 24K/20K GPU 2
[15:23:56] Accepted 5021c5f0 Diff 209K/20K GPU 3
[15:23:59] Accepted 01b75a5f Diff 38.2K/20K GPU 1
[15:24:01] Accepted 026cc3f2 Diff 27K/20K GPU 3
[15:24:03] Accepted 16f362c7 Diff 731K/20K GPU 2
[15:24:11] Accepted 1f8c7900 Diff 532K/20K GPU 2
[15:24:27] Accepted 019cadd3 Diff 40.7K/20K GPU 1
[15:25:10] Accepted 031e6a98 Diff 21K/20K GPU 2
[15:25:19] Accepted 03374887 Diff 20.4K/20K GPU 3
[15:25:33] Accepted 02b7efa8 Diff 24.1K/20K GPU 3
[15:25:52] Accepted 02555c07 Diff 28.1K/20K GPU 3
I have a RX550 Rig with 6 Cards and use Claymore 9.7 and the hole System runs with 1875 H/s. Just use stock clockings and use -h 512 and each card runs over 300 H/s.
Jump to: