Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 476.

BulldogPO

newbie

Activity: 20

Merit: 0

Used these instructions there:
https://www.techpowerup.com/228536/amd-bios-signature-check-re-enabled-with-relive-locks-out-polaris-bios-modders

And modded ASUS RX570 4GB Expedition orginal BIOS (extracted with GPU-Z) with Polaris BIOS editor and one key memory mod button.
I try with that 17.12.2 Adrenalin after work. Thank you!

BulldogPO

newbie

Activity: 20

Merit: 0

I tried to mod bios but now Windows does BSOD when installing blockchain drivers.

muzuca

member

Activity: 182

Merit: 13

Quote from: BulldogPO on January 16, 2018, 01:18:44 AM

Please help me, I´m suffering from low hash speeds with Claymore.
System:
- ASRock H110 BTC mobo
- Celeron G3930
- 4GB DDR4 2133MHz stick
- 64GB Adata SATA SSD
- Cooler master Silent Pro 800W
- 2pcs ASUS Radeon RX570 4GB Expedition

Windows 10 Pro + AMD Blockchain drivers
ETH Hashspeed is max 15MH/s per card Sad

Any idea what should i do next?

Did you bios modded your GPUs? If yes, what it’s you claymore config? Probably you need to setup cclock, mclock, mvddc and cvddc.

Ursul0

sr. member

Activity: 857

Merit: 262

Quote from: JKDK on January 15, 2018, 06:49:00 AM

Hello i have this problem with 1 of the cards in my rig.
Its a 7 card rig.
GPU hangs in OpenCL call, exit error

I have try alot of things. Right now i run
-epsw x -mode 1 -cclock 1200,1200,1200,1200,1200,1200,1200 -mclock 2250,2250,2200,2200,2250,2200,2250, -cvddc 880,850,850,850,850,850,850 -mvddc 920,900,900,900,900,900,900 -gser 8 -dcri 5 -wd 0 -ftime 10 -lidag 3,0,0,0,0,0,0 -tstop 85 -tt 60 -fanmin 10 -fanmax 100

It is GPU0 there get this error. Any ideas? It can happen after minutes or hours

you should try lowering mem clock for the GPU that fails.
Also why do you think that setting core volts lower then vrm would work?

Marvell2

full member

Activity: 1148

Merit: 132

Biakal , blake 40ghs, Lbr 40gh or sia 20gh miner is out profitability of dual mining with claymore is gone
basically cut by 2/3

please add a new algo or reduce fee , i switched all my miners to eth olny

BulldogPO

newbie

Activity: 20

Merit: 0

Please help me, I´m suffering from low hash speeds with Claymore.
System:
- ASRock H110 BTC mobo
- Celeron G3930
- 4GB DDR4 2133MHz stick
- 64GB Adata SATA SSD
- Cooler master Silent Pro 800W
- 2pcs ASUS Radeon RX570 4GB Expedition

Windows 10 Pro + AMD Blockchain drivers
ETH Hashspeed is max 15MH/s per card Sad

Any idea what should i do next?

e97

jr. member

Activity: 58

Merit: 1

thanks claymore!

shows 44 Mh/s on Vega64 and 37 Mh/s on 1080 Ti, hopefully number of submitted shares shows a similar increase

ethminer seems to run a bit faster on the 1080 Ti, any chance you could integrate those improvements? might be from cuda-9 code.

Reported:

miner	vega 64	1080 ti	combined
ethminer	42	38	80
claymore	44	37	81

Will report back on accepted share rate after 24 hours.

muzuca

member

Activity: 182

Merit: 13

Quote from: MarkSinn on January 15, 2018, 09:25:56 AM

new Claymore 10.4 have issue with blockchain driver ?

I’m using in Windows 10 with blockchain Aug 23 drivers and its working perfect.

da_vincicode

newbie

Activity: 2

Merit: 0

Sia Mining is working with Vega 64 cards with v10.4! Thanks Claymore!

Detailed video is available here: https://youtu.be/9iD68EZ5lps

agu3000

member

Activity: 276

Merit: 31

Hi im mining ETH only using last Claymore its working but Total Shares always get 0 (no reject) and in the nanopool not show any Hashrate any idea?

AlainC

member

Activity: 91

Merit: 10

Quote from: MRCollyns on January 15, 2018, 09:59:05 AM

Solved my own problem.. ROCm needs to be installed after the AMDGPU Blockchain drivers for Ubuntu... Happy Mining!

with latest AMDGPU-PRO v17.50 no need of ROCm...
I've installed a blank ubuntu 16.04 with amdgpu 17.50 --compute... it works perfectly.
but with previous version ROCm was solving DAG limitation (activate big 2M pages).

MRCollyns

newbie

Activity: 3

Merit: 0

Solved my own problem.. ROCm needs to be installed after the AMDGPU Blockchain drivers for Ubuntu... Happy Mining!

MarkSinn

newbie

Activity: 182

Merit: 0

new Claymore 10.4 have issue with blockchain driver ?

MRCollyns

newbie

Activity: 3

Merit: 0

Quote from: ?? on ??

Quote from: mshordja on January 15, 2018, 04:49:56 AM

Can any one confirm that this version of Claymore's work with the last drive of ati? with work i mean, dag fix, over and underclock, and fan control?
thanks

Works for me!

What OS are you running?

mshordja

member

Activity: 146

Merit: 10

Quote from: JKDK on January 15, 2018, 07:17:31 AM

Quote from: mshordja on January 15, 2018, 07:00:33 AM

Quote from: JKDK on January 15, 2018, 06:49:00 AM

Hello i have this problem with 1 of the cards in my rig.
Its a 7 card rig.
GPU hangs in OpenCL call, exit error

I have try alot of things. Right now i run
-epsw x -mode 1 -cclock 1200,1200,1200,1200,1200,1200,1200 -mclock 2250,2250,2200,2200,2250,2200,2250, -cvddc 880,850,850,850,850,850,850 -mvddc 920,900,900,900,900,900,900 -gser 8 -dcri 5 -wd 0 -ftime 10 -lidag 3,0,0,0,0,0,0 -tstop 85 -tt 60 -fanmin 10 -fanmax 100

It is GPU0 there get this error. Any ideas? It can happen after minutes or hours

have you check the riser?

Yes i have changed it to another 1 but i still suspekt the riser. I have try to under/overvolt, under/overclock the gpu and memory

try to change the PCI you have insert the riser with another GPU riser. I fix in that way once

jrr

newbie

Activity: 24

Merit: 0

Quote from: Claymore on January 14, 2018, 09:09:25 AM

v10.4:

- fixed issue with rejected shares in ETH+SIA mode for Vega cards.
- improved watchdog for temperature/fan management thread.

I'm have a problem when running it as a Task, the gpu infos(temperature and fan speed) don't show on web monitor. If I run normally by clicking in the start.bat, it works as expected.

It is not a problem in just the 10.4 version, I have used the 10.3 for a while and it never showed the gpu info when running as task.

I have the problem in two computers, the same config, both with one with XFX Rx 580 8GB or other with 4GB;

The configuration on the task or in the start.bat file is the same, I tried -wd 1, which is the default, but didn't work.

Someone else has the same problem?

JKDK

newbie

Activity: 20

Merit: 0

Quote from: mshordja on January 15, 2018, 07:00:33 AM

Quote from: JKDK on January 15, 2018, 06:49:00 AM

Hello i have this problem with 1 of the cards in my rig.
Its a 7 card rig.
GPU hangs in OpenCL call, exit error

I have try alot of things. Right now i run
-epsw x -mode 1 -cclock 1200,1200,1200,1200,1200,1200,1200 -mclock 2250,2250,2200,2200,2250,2200,2250, -cvddc 880,850,850,850,850,850,850 -mvddc 920,900,900,900,900,900,900 -gser 8 -dcri 5 -wd 0 -ftime 10 -lidag 3,0,0,0,0,0,0 -tstop 85 -tt 60 -fanmin 10 -fanmax 100

It is GPU0 there get this error. Any ideas? It can happen after minutes or hours

have you check the riser?

Yes i have changed it to another 1 but i still suspekt the riser. I have try to under/overvolt, under/overclock the gpu and memory

mshordja

member

Activity: 146

Merit: 10

Quote from: JKDK on January 15, 2018, 06:49:00 AM

Hello i have this problem with 1 of the cards in my rig.
Its a 7 card rig.
GPU hangs in OpenCL call, exit error

I have try alot of things. Right now i run
-epsw x -mode 1 -cclock 1200,1200,1200,1200,1200,1200,1200 -mclock 2250,2250,2200,2200,2250,2200,2250, -cvddc 880,850,850,850,850,850,850 -mvddc 920,900,900,900,900,900,900 -gser 8 -dcri 5 -wd 0 -ftime 10 -lidag 3,0,0,0,0,0,0 -tstop 85 -tt 60 -fanmin 10 -fanmax 100

It is GPU0 there get this error. Any ideas? It can happen after minutes or hours

have you check the riser?

JKDK

newbie

Activity: 20

Merit: 0

Hello i have this problem with 1 of the cards in my rig.
Its a 7 card rig.
GPU hangs in OpenCL call, exit error

I have try alot of things. Right now i run
-epsw x -mode 1 -cclock 1200,1200,1200,1200,1200,1200,1200 -mclock 2250,2250,2200,2200,2250,2200,2250, -cvddc 880,850,850,850,850,850,850 -mvddc 920,900,900,900,900,900,900 -gser 8 -dcri 5 -wd 0 -ftime 10 -lidag 3,0,0,0,0,0,0 -tstop 85 -tt 60 -fanmin 10 -fanmax 100

It is GPU0 there get this error. Any ideas? It can happen after minutes or hours

mshordja

member

Activity: 146

Merit: 10

Quote from: ?? on ??

I have a question:

Currently I am mining PIRL, however due to the DevFee it will restart the miner every hour or so to generate a new DAG.

I'm running with -allcoins 1, I've already tried -allcoins -1 (which crashes the miner).

Any ideas on how to not regenerate every time?

i am mining DBIX and happens the same, is the dev fee that generate dag file for ETH. I think is normal, but i haven't any problem and now its normal for me Cheesy

Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 476. (Read 6590718 times)