Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 521.

Call_Me_Bambi

sr. member

Activity: 574

Merit: 261

Quote from: r12x2 on December 03, 2017, 12:17:25 PM

Is it possible to mine minexcoin with Claymore's Dual miner?

Thank you.

Short answer, No.
Minexcoin is an Equihash coin so you will need an equihash miner such as Claymore's ZCash/BTG AMD GPU Miner. You can find out more about it here, https://bitcointalksearch.org/topic/claymores-zcashbtg-amd-gpu-miner-v126-windowslinux-1670733

Vann

hero member

Activity: 1036

Merit: 606

Most likely your overclock settings are too high or you are undervolting too much. With a modded Bios on a RX 470/480 or RX 570 you need to run the pixel patcher after installing the drivers to bypass the Bios signature check or you will have a code 43 error in the Windows Device manager.

https://www.monitortests.com/forum/Thread-AMD-ATI-Pixel-Clock-Patcher

The AMD blockchain drivers also have issues in Windows 7. Try the Robinhood blockchain driver

https://bitcointalksearch.org/topic/m.25638744

Stingfisher

newbie

Activity: 9

Merit: 0

I have an ASUS rx480 Strix 8GB. I only get 19.8 Mh/s. I know its because of the drivers. But if i install the AMD blockchain drivers from August, Windows very often crashes and reboots, and Claymore 10.0 always crashes after a few seconds.

In newer AMD drivers its possible to toggle between "graphics" and "compute" with the "GPU workload" option. But the "GPU workload" toggle doesnt show up on my machine :-(. I've tried with a XFX rx470 card, but same problems.

Even copying memstrap 1750 -> 2000 doesnt work for me. Claymore doesnt recognize the card if I do that. I have Windows 7, but it seem like I have to go back to Linux again. I have Googled a lot, but I have not found any solutions.

Anyone here that experienced the same problems, and found a solution?

duniek

member

Activity: 70

Merit: 10

is this possible to arrange custom lines in CMD in widnows?

for exapmple in column?

TOTAL SPEED: xxx.xx MH/S
GPU0 xx.xx MH/s
GPU1 xx.xx MH/s
GPU2 xx.xx MH/s
GPU3 xx.xx MH/s

maybe even without fan speed/temp ?

r12x2

newbie

Activity: 68

Merit: 0

Is it possible to mine minexcoin with Claymore's Dual miner?

Thank you.

sdf9000

newbie

Activity: 4

Merit: 0

Quote from: sdf9000 on December 03, 2017, 08:20:48 AM

Hi all, first post so be kind... I have been using Claymore for a little while with great success. I don't consider i have learnt enough yet to be guiding people so have not been posting!

However, I have run into a problem that i can't appear to fix.
My current setup is running 2x RX580 (red dragon - hynix) and using the command line options either both in the .bat file or config.txt i can change my GPU0 voltage, clock speed etc. But, my second card does not respond to this.

I am on windows 10 pro 64bit
Radeon Software Version: 17.11.1

Both cards have been bios flashed with the same bios, both cards are identical even down to the batch number Wink

Currently hashing on 1st card at 29.4, second card at 28.4, second card is using much more power and not applying my designated overclock / fan / underclock & undervolts.

I have tried Crossfire enabled & Disabled.
Driver is set to "Compute" mode.

I can't use the BETA driver because this system is used for rendering video as well as an offload for my workstation, this driver is terrible for it and causes errors.

Currently my config.txt looks like:

Code:

-epsw x
-mode 1
-ftime 10
-esm 0
-etha 0
-asm 1
-estale 0
-mode 0
-retrydelay 2
-tt 70,77
-tstop 77,77
-fanmax 90,90
-fanmin 30,30
-cclock 1100,1100
-mclock 2100,2100
-cvddc 840,840
-mvddc 840,840
-platform 1

Derp... create a profile for the .exe in the Radeon driver - answered my own question, removed my extra values here. Configured each card as required.

sdf9000

newbie

Activity: 4

Merit: 0

Hi all, first post so be kind... I have been using Claymore for a little while with great success. I don't consider i have learnt enough yet to be guiding people so have not been posting!

However, I have run into a problem that i can't appear to fix.
My current setup is running 2x RX580 (red dragon - hynix) and using the command line options either both in the .bat file or config.txt i can change my GPU0 voltage, clock speed etc. But, my second card does not respond to this.

I am on windows 10 pro 64bit
Radeon Software Version: 17.11.1

Both cards have been bios flashed with the same bios, both cards are identical even down to the batch number Wink

Currently hashing on 1st card at 29.4, second card at 28.4, second card is using much more power and not applying my designated overclock / fan / underclock & undervolts.

I have tried Crossfire enabled & Disabled.
Driver is set to "Compute" mode.

I can't use the BETA driver because this system is used for rendering video as well as an offload for my workstation, this driver is terrible for it and causes errors.

Currently my config.txt looks like:

Code:

-epsw x
-mode 1
-ftime 10
-esm 0
-etha 0
-asm 1
-estale 0
-mode 0
-retrydelay 2
-tt 70,77
-tstop 77,77
-fanmax 90,90
-fanmin 30,30
-cclock 1100,1100
-mclock 2100,2100
-cvddc 840,840
-mvddc 840,840
-platform 1

Munka9

newbie

Activity: 30

Merit: 0

Hi,

I am also getting the error:
Temperature control thread hangs, need to restart miner!

It happens about every 20 to 40 minutes.

Its definitely not an AMD driver issue as suggested above because I use NVIDIA cards.

I have 4 rigs, 2 NVIDIA, 2 AMD, this only happens on my larger NVIDIA Rig. Have reverted to 10.0 for now on the rig with the problem until its fixed.

gOCe

newbie

Activity: 46

Merit: 0

Review in Gpu-z if your clock and mem are really changed.
Maybe you have - memclock on your config or your bat. Or you have a wrong AB version

Quote from: Darkeind on December 02, 2017, 06:51:33 PM

Quote from: heavyarms1912 on December 02, 2017, 05:05:26 PM

Quote from: SiliconKid on December 02, 2017, 03:30:11 PM

Quote from: Darkeind on December 02, 2017, 12:36:43 PM

Hello,

I dont know if you can help me but I have a problem with my RX 580 radeon pulse under window 10. When I launch claymore I have 22 Mhs with a memory clock of 2000Mhz. However when I overlock the 580 with afterburner to 2100Mhz or higher the Mhs does not change and stay at 22. it is really strange because I can overlock my 1060 with not problems.

Do you know what the issue could be? Or do you know where I can find the answer?

Thanks a lot in advance

This is probably because of the driver you have installed.

If you are running in Windows 10 you MUST install the AMD Crypto mining BETA driver if you want to get your hashrate up to around 27 to 30 MH/s on a 580.

http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-[Suspicious link removed]pute-Release-Notes.aspx

I had the exact same problem. I had the latest Catalyst Crimson drivers installed and I couldn't get higher than 22 MH/s, no matter what I did.

Then I uninstalled those drivers with DDU, and installed the AMD Crypto Mining BETA drivers, and I was immediately able to get 31 MH/s, but with some errors. After some fine tuning I can now get 28 MH/s on every RX580 in my rigs, with zero errors.

It's the driver.

With the crimson relive drivers post Oct 24th you need to switch to compute workload by Right click > AMD settings > Gaming > Global settings > change GPU workload to Compute instead of Graphics.
Need to do this for all gpu individually. You would get same hashrate as the blockchain drivers.

Hi guys, I had the special driver just as bellow but I was block to 22. I tried the last driver and i used the Compute instead of Graphics option but it changed nothing even with 2150 i get 22. Any other idea?

http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-[Suspicious link removed]pute-Release-Notes.aspx

hiimj

newbie

Activity: 1

Merit: 0

Hello, recently I've been having some issues with Claymore Crashing. Here's what the problem is

Code:

05:19:47:424 1070 ETH: job changed
05:19:47:455 1070 new buf size: 0
05:19:47:487 1070 ETH: 12/03/17-05:19:47 - New job from eth-asia1.nanopool.org:9999
05:19:47:518 1070 target: 0x00000000dbe6fece (diff: 5000MH), epoch 155(2.21GB)
05:19:47:549 1070 ETH - Total Speed: 176.818 Mh/s, Total Shares: 302, Rejected: 0, Time: 02:28
05:19:47:580 1070 ETH: GPU0 29.435 Mh/s, GPU1 29.479 Mh/s, GPU2 29.504 Mh/s, GPU3 29.445 Mh/s, GPU4 29.494 Mh/s, GPU5 29.461 Mh/s
05:19:55:550 1070 ETH: checking pool connection...
05:19:55:613 1070 send: {"worker": "", "jsonrpc": "2.0", "params": [], "id": 3, "method": "eth_getWork"}

05:19:56:035 1070 got 243 bytes
05:19:56:097 1070 buf: {"jsonrpc":"2.0","id":0,"result":["0x1f78ef3ec1d617fa5f2fd8cb6d220be91f1886759262e2c15bff96bc2fc68d62","0x1e9891b51a83da3e735c71999400fc8927e8614e86fc37e618d3781578d5c939","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}

05:19:56:128 1070 parse packet: 242
05:19:56:160 1070 ETH: job is the same
05:19:56:191 1070 new buf size: 0
05:20:00:160 1928 ETH: put share nonce a8bf720c0ad6ab59
05:20:00:207 1070 send: {"id":6,"worker":"jus1","jsonrpc":"2.0","method":"eth_submitHashrate","params":["0xa796639", "0x00000000000000000000000000000000000000000000000000000000de40a7fd"]}

05:20:00:222 1928 ETH round found 1 shares
05:20:00:269 1070 ETH: 12/03/17-05:20:00 - SHARE FOUND - (GPU 5)
05:20:00:301 1070 send: {"worker":"jus1","id":15,"method":"eth_submitWork","params":["0xa8bf720c0ad6ab59","0x1f78ef3ec1d617fa5f2fd8cb6d220be91f1886759262e2c15bff96bc2fc68d62","0xcbec156494b035ab3b3c671f77da896840f281082c463a55793610fa2bee27b3"]}

05:20:00:488 1070 got 243 bytes
05:20:00:551 1070 buf: {"jsonrpc":"2.0","id":0,"result":["0x2423126065261830b5f76127963807a4576f2408603e768eee0d904509e60873","0x1e9891b51a83da3e735c71999400fc8927e8614e86fc37e618d3781578d5c939","0x00000000dbe6fecebdedd5beb573440e5a884d1b2fbf06fcce912adcb8d8422e"]}

05:20:00:566 1070 parse packet: 242
05:20:00:598 1070 ETH: job changed
05:20:00:629 1070 new buf size: 0
05:20:00:660 1070 ETH: 12/03/17-05:20:00 - New job from eth-asia1.nanopool.org:9999
05:20:00:691 1070 target: 0x00000000dbe6fece (diff: 5000MH), epoch 155(2.21GB)
05:20:00:723 1070 ETH - Total Speed: 176.748 Mh/s, Total Shares: 303, Rejected: 0, Time: 02:29
05:20:00:754 1070 ETH: GPU0 29.441 Mh/s, GPU1 29.463 Mh/s, GPU2 29.469 Mh/s, GPU3 29.466 Mh/s, GPU4 29.427 Mh/s, GPU5 29.482 Mh/s
05:20:00:785 1070 got 40 bytes
05:20:00:816 1070 buf: {"jsonrpc":"2.0","id":15,"result":true}

05:20:00:848 1070 parse packet: 39
05:20:00:879 1070 ETH: Share accepted (547 ms)!

05:20:00:910 1070 new buf size: 0
05:20:03:957 1498 em hbt: 15, fm hbt: 15,
05:20:03:973 1498 Temperature control thread hangs, need to restart miner!

http://sv1.upsieutoc.com/2017/12/03/1111.png
What might be causing this, it wasn't running for very long when it did this. Yesterday it ran for 1 to 3 hours, then did the same thing.

Darkeind

newbie

Activity: 3

Merit: 0

Quote from: heavyarms1912 on December 02, 2017, 05:05:26 PM

Quote from: SiliconKid on December 02, 2017, 03:30:11 PM

Quote from: Darkeind on December 02, 2017, 12:36:43 PM

Hello,

I dont know if you can help me but I have a problem with my RX 580 radeon pulse under window 10. When I launch claymore I have 22 Mhs with a memory clock of 2000Mhz. However when I overlock the 580 with afterburner to 2100Mhz or higher the Mhs does not change and stay at 22. it is really strange because I can overlock my 1060 with not problems.

Do you know what the issue could be? Or do you know where I can find the answer?

Thanks a lot in advance

This is probably because of the driver you have installed.

If you are running in Windows 10 you MUST install the AMD Crypto mining BETA driver if you want to get your hashrate up to around 27 to 30 MH/s on a 580.

http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-[Suspicious link removed]pute-Release-Notes.aspx

I had the exact same problem. I had the latest Catalyst Crimson drivers installed and I couldn't get higher than 22 MH/s, no matter what I did.

Then I uninstalled those drivers with DDU, and installed the AMD Crypto Mining BETA drivers, and I was immediately able to get 31 MH/s, but with some errors. After some fine tuning I can now get 28 MH/s on every RX580 in my rigs, with zero errors.

It's the driver.

With the crimson relive drivers post Oct 24th you need to switch to compute workload by Right click > AMD settings > Gaming > Global settings > change GPU workload to Compute instead of Graphics.
Need to do this for all gpu individually. You would get same hashrate as the blockchain drivers.

Hi guys, I had the special driver just as bellow but I was block to 22. I tried the last driver and i used the Compute instead of Graphics option but it changed nothing even with 2150 i get 22. Any other idea?

http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-[Suspicious link removed]pute-Release-Notes.aspx

heavyarms1912

full member

Activity: 729

Merit: 114

Quote from: SiliconKid on December 02, 2017, 03:30:11 PM

Quote from: Darkeind on December 02, 2017, 12:36:43 PM

Hello,

I dont know if you can help me but I have a problem with my RX 580 radeon pulse under window 10. When I launch claymore I have 22 Mhs with a memory clock of 2000Mhz. However when I overlock the 580 with afterburner to 2100Mhz or higher the Mhs does not change and stay at 22. it is really strange because I can overlock my 1060 with not problems.

Do you know what the issue could be? Or do you know where I can find the answer?

Thanks a lot in advance

This is probably because of the driver you have installed.

If you are running in Windows 10 you MUST install the AMD Crypto mining BETA driver if you want to get your hashrate up to around 27 to 30 MH/s on a 580.

http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-[Suspicious link removed]pute-Release-Notes.aspx

I had the exact same problem. I had the latest Catalyst Crimson drivers installed and I couldn't get higher than 22 MH/s, no matter what I did.

Then I uninstalled those drivers with DDU, and installed the AMD Crypto Mining BETA drivers, and I was immediately able to get 31 MH/s, but with some errors. After some fine tuning I can now get 28 MH/s on every RX580 in my rigs, with zero errors.

It's the driver.

With the crimson relive drivers post Oct 24th you need to switch to compute workload by Right click > AMD settings > Gaming > Global settings > change GPU workload to Compute instead of Graphics.
Need to do this for all gpu individually. You would get same hashrate as the blockchain drivers.

SiliconKid

newbie

Activity: 2

Merit: 0

Quote from: Darkeind on December 02, 2017, 12:36:43 PM

Hello,

I dont know if you can help me but I have a problem with my RX 580 radeon pulse under window 10. When I launch claymore I have 22 Mhs with a memory clock of 2000Mhz. However when I overlock the 580 with afterburner to 2100Mhz or higher the Mhs does not change and stay at 22. it is really strange because I can overlock my 1060 with not problems.

Do you know what the issue could be? Or do you know where I can find the answer?

Thanks a lot in advance

This is probably because of the driver you have installed.

If you are running in Windows 10 you MUST install the AMD Crypto mining BETA driver if you want to get your hashrate up to around 27 to 30 MH/s on a 580.

http://support.amd.com/en-us/kb-articles/Pages/Radeon-Software-Crimson-ReLive-Edition-Beta-for-[Suspicious link removed]pute-Release-Notes.aspx

I had the exact same problem. I had the latest Catalyst Crimson drivers installed and I couldn't get higher than 22 MH/s, no matter what I did.

Then I uninstalled those drivers with DDU, and installed the AMD Crypto Mining BETA drivers, and I was immediately able to get 31 MH/s, but with some errors. After some fine tuning I can now get 28 MH/s on every RX580 in my rigs, with zero errors.

It's the driver.

mikkowendell

newbie

Activity: 41

Merit: 0

Quote from: Darkeind on December 02, 2017, 12:36:43 PM

Hello,

I dont know if you can help me but I have a problem with my RX 580 radeon pulse under window 10. When I launch claymore I have 22 Mhs with a memory clock of 2000Mhz. However when I overlock the 580 with afterburner to 2100Mhz or higher the Mhs does not change and stay at 22. it is really strange because I can overlock my 1060 with not problems.

Do you know what the issue could be? Or do you know where I can find the answer?

Thanks a lot in advance

backread, review everything like bios mod and your rx 580 driver.

AlainC

member

Activity: 91

Merit: 10

Quote from: Darkeind on December 02, 2017, 12:36:43 PM

However when I overlock the 580 with afterburner to 2100Mhz or higher the Mhs does not change and stay at 22

I've see that if I don't change the memory straps... search around that concept, it is a FAQ.
increasing frequency while not changing memory timings is like accelerating your car in a city, while the traffic light don't change timing, small effect.

Darkeind

newbie

Activity: 3

Merit: 0

Hello,

I dont know if you can help me but I have a problem with my RX 580 radeon pulse under window 10. When I launch claymore I have 22 Mhs with a memory clock of 2000Mhz. However when I overlock the 580 with afterburner to 2100Mhz or higher the Mhs does not change and stay at 22. it is really strange because I can overlock my 1060 with not problems.

Do you know what the issue could be? Or do you know where I can find the answer?

Thanks a lot in advance

Jackblow33

newbie

Activity: 48

Merit: 0

Quote from: daniellrglobal on December 02, 2017, 10:17:34 AM

Hi All,

I need a help. Having NVIDIA 210 and windows 8 OS 64 bit. Have downloaded the claymore dual. I am editing the start file. What location i need to give?

I am from india and what pool i need to choose?

Your card probably have 1gb of DDR, don`t waste your time you don`t have enough memory to mine ethereum and not a single shit coin could be worth mining with this. Upgrading Gpu is the only option.

daniellrglobal

newbie

Activity: 5

Merit: 0

Hi All,

I need a help. Having NVIDIA 210 and windows 8 OS 64 bit. Have downloaded the claymore dual. I am editing the start file. What location i need to give?

I am from india and what pool i need to choose?

Metroid

sr. member

Activity: 2142

Merit: 353

Xtreme Monster

Quote from: Claymore on November 30, 2017, 02:21:07 PM

.........

@Claymore, anyway you could add a setting that stops dual mining if a set temperature is reached? For example, if I set "ttdcr 75" it will keep reducing the intensity as the temperature rises and I think it will only stop dual mining when it reaches 90 Celsius. If I set "ttdcr 65" then I think it will stop dual mining only when it reached 80 Celsius however from 65 to 80 it will lower the intensity. So I'm requesting if you can do something to stop dual mining if a set temperature is reached and return back to normal if the temperature is lower than the set temperature. So basically this setting would just automatically set main mining or dual mining based on a set temperature.

g0lddi99er

newbie

Activity: 3

Merit: 0

Quote from: Flickspeed on December 01, 2017, 01:53:55 PM

Quote from: Flickspeed on November 30, 2017, 02:20:08 PM

Hi, Is there something wrong with the late teamviewer versions alongside the most recent windows 10 version? Claymore becomes stuck at "start building OpenCL program for GPU 0..." if I am logged on with teamviewer. If I am not logged on it starts mining as normal. Once I logon GPU 0 Hangs in open cl and miner continue with the rest of the cards. Thats ofcourse because I have -wd 0 and -r -1. Otherwise everything works very well until you connect with teamviewer. Is there any setting to be changed?

bump, this is really bugging me on 2 different miners with latest version of windows (1709 fall 2017 update) I am still uncertain if its windows, teamviewer or claymore miner at fault.

I have been seeing similar issues with GPU 0 after I upgraded to the latest Win release. I did a lot of troubleshooting but did not think to disable TeamViewer (I will try it when I get a chance to see if it makes any difference). A workaround that worked for me was to plug in a monitor into the DVI port on the GPU 0. The monitor did not even need to be powered on for it to work (plugged in power but in standby mode). Not 100% sure if it is going to work for you but might be worth giving it a try.

Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 521. (Read 6590757 times)