Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 961.

doktor83

hero member

Activity: 2548

Merit: 626

Quote from: Qazo on April 09, 2017, 01:43:52 PM

yes, for now Cheesy

i tried to raise memory more but didn't get better result

i only modified straps 1750-2000, nothing else, very happy with results

Try 1130/2150, maybe you get more, i think 1075 is too low.

fittsy

sr. member

Activity: 441

Merit: 252

Quote from: AzzAz on April 09, 2017, 12:33:00 PM

for me -dpool stratum+tcp://dcr.suprnova.cc:2252 is not working, but -dpool dcr.suprnova.cc:2252

You're right. I hadn't had enough coffee and didn't even notice that!

I'll correct my original post for future people who might want to copy/paste. Thanks for helping me out.

Qazo

full member

Activity: 211

Merit: 101

yes, for now Cheesy

i tried to raise memory more but didn't get better result

i only modified straps 1750-2000, nothing else, very happy with results

doktor83

hero member

Activity: 2548

Merit: 626

all of your cards can handle 2150mhz mem ?

Qazo

full member

Activity: 211

Merit: 101

Quote from: coinzoid on April 08, 2017, 08:25:07 AM

You are forcing max load limits on your PSU. Consider adding a second PSU.

Quote from: Truthchanter on April 08, 2017, 09:13:02 AM

You want to undervolt to lower the energy consumption. Somewhere between 900mv to 950mv should work well. maybe even 880mv if you're lucky. Make sure you reduce both core and mem voltage to same value too

so after little bit tuning today, I got this

and from wall

GPU2 was hanging on these setup so I only set that card to 950mv , it's stable now (will test overnight)

-dcri 30, if I set it to 35 I get 10mh/s less on ETH and only 300 mhs more on DCR - not worth it and 30W more power consumption

In the end
power consumption lowered by 7% and mhs and power are much more stable now

Blamsud

sr. member

Activity: 503

Merit: 250

Quote from: AzzAz on April 09, 2017, 12:33:00 PM

Quote from: fittsy on April 09, 2017, 12:19:11 PM

Quote from: matmator on April 09, 2017, 04:10:22 AM

Hello

I do not understand what to put in the command line for the DCR?

Do not put wallet address?

Login and pass the pool account?

i use claymore :

EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0x242a8722fE288FCA7eF03b627D0C78799166C695/PC/[email protected] -dpool stratum+tcp://dcr.suprnova.cc:2252 -dwal DskqH7NwywxaaYENnQt6kBz28aBzKUUdFjb.PC -dpsw x -allpools 1 -r 1 -dcri 30

command ok ?

DCR share rejected ................ Huh

Did anyone ever reply to you?

On Suprnova you use a username to login to suprnova across all their pools. You need to register on suprnova to get that username. Once you have that username you use it instead of your wallet address. Your wallet address is kept inside suprnova under your account settings.

so your command line would look something like:

Code:

EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0x242a8722fE288FCA7eF03b627D0C78799166C695/PC/[email protected] -dpool stratum+tcp://dcr.suprnova.cc:2252 -dwal username.workername -dpsw x -allpools 1 -r 1 -dcri 30 -dcoin dcr

As stated I don't think you have to use the -dcoin but it's good practice to use anyway.

After you register on suprnova click on "My Account" in the left hand navigation. Then click on "Edit Account". That's where you'll be able to add your wallet address and configure how often you want payouts.

for me -dpool stratum+tcp://dcr.suprnova.cc:2252 is not working, but -dpool dcr.suprnova.cc:2252

Similar here, I cannot use http://

AzzAz

legendary

Activity: 1030

Merit: 1006

Quote from: fittsy on April 09, 2017, 12:19:11 PM

Quote from: matmator on April 09, 2017, 04:10:22 AM

Hello

I do not understand what to put in the command line for the DCR?

Do not put wallet address?

Login and pass the pool account?

i use claymore :

EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0x242a8722fE288FCA7eF03b627D0C78799166C695/PC/[email protected] -dpool stratum+tcp://dcr.suprnova.cc:2252 -dwal DskqH7NwywxaaYENnQt6kBz28aBzKUUdFjb.PC -dpsw x -allpools 1 -r 1 -dcri 30

command ok ?

DCR share rejected ................ Huh

Did anyone ever reply to you?

On Suprnova you use a username to login to suprnova across all their pools. You need to register on suprnova to get that username. Once you have that username you use it instead of your wallet address. Your wallet address is kept inside suprnova under your account settings.

so your command line would look something like:

Code:

EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0x242a8722fE288FCA7eF03b627D0C78799166C695/PC/[email protected] -dpool stratum+tcp://dcr.suprnova.cc:2252  -dwal username.workername -dpsw x -allpools 1 -r 1 -dcri 30 -dcoin dcr

As stated I don't think you have to use the -dcoin but it's good practice to use anyway.

After you register on suprnova click on "My Account" in the left hand navigation. Then click on "Edit Account". That's where you'll be able to add your wallet address and configure how often you want payouts.

for me -dpool stratum+tcp://dcr.suprnova.cc:2252 is not working, but -dpool dcr.suprnova.cc:2252

fittsy

sr. member

Activity: 441

Merit: 252

Quote from: matmator on April 09, 2017, 04:10:22 AM

Hello

I do not understand what to put in the command line for the DCR?

Do not put wallet address?

Login and pass the pool account?

i use claymore :

EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0x242a8722fE288FCA7eF03b627D0C78799166C695/PC/[email protected] -dpool dcr.suprnova.cc:2252 -dwal DskqH7NwywxaaYENnQt6kBz28aBzKUUdFjb.PC -dpsw x -allpools 1 -r 1 -dcri 30

command ok ?

DCR share rejected ................ Huh

Did anyone ever reply to you?

On Suprnova you use a username to login to suprnova across all their pools. You need to register on suprnova to get that username. Once you have that username you use it instead of your wallet address. Your wallet address is kept inside suprnova under your account settings.

so your command line would look something like:

Code:

EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0x242a8722fE288FCA7eF03b627D0C78799166C695/PC/[email protected] -dpool stratum+tcp://dcr.suprnova.cc:2252  -dwal username.workername -dpsw x -allpools 1 -r 1 -dcri 30 -dcoin dcr

As stated I don't think you have to use the -dcoin but it's good practice to use anyway.

After you register on suprnova click on "My Account" in the left hand navigation. Then click on "Edit Account". That's where you'll be able to add your wallet address and configure how often you want payouts.

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: kirilvvbg on April 09, 2017, 11:06:18 AM

Please help - I cannot figure out EthMan: on some of my rigs it is working perfectly. But in some it says (in red):
Remote management: read-only only, command miner_restart ignored.
Where is the problem? Claymore?

First post of this thread, check "-mport" option description. Since v8.1, remote management is working in read-only mode by default.

kirilvvbg

full member

Activity: 213

Merit: 100

Please help - I cannot figure out EthMan: on some of my rigs it is working perfectly. But in some it says (in red):
Remote management: read-only only, command miner_restart ignored.
Where is the problem? Claymore?

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: nicog5 on April 09, 2017, 10:22:15 AM

@Claymoere
Dear Claymore, this is my first post here and I'd like first of all thank you so much for your work and effort.
I think there is a problem with v9 and pascal coin mining: if I enter any pascal coin pool and set the -dcoin option to pasc, than the miner automatically mines without asm mode regardless -asm is set to 1 or to 0. In this case I can not profit with asm mode gains.
Please check it. I Have 5 RX480-s running under windows 10 OS.
Thanks in advance.

Please read fourth text line of first post in this thread.
I'm still working on other coins...

Cacaparg

hero member

Activity: 835

Merit: 502

Quote from: mewhoyou on April 09, 2017, 10:34:02 AM

Need help... when ever i run on dual mining my PC restarts within 30 seconds of mining. Any suggestions?? Any dual coin but if i run single ETH it works like a charm.

Your power supply is not strong enough. You need to reduce the intensity or voltage or clock.

mewhoyou

sr. member

Activity: 353

Merit: 250

Need help... when ever i run on dual mining my PC restarts within 30 seconds of mining. Any suggestions?? Any dual coin but if i run single ETH it works like a charm.

nicog5

newbie

Activity: 64

Merit: 0

@Claymoere
Dear Claymore, this is my first post here and I'd like first of all thank you so much for your work and effort.
I think there is a problem with v9 and pascal coin mining: if I enter any pascal coin pool and set the -dcoin option to pasc, than the miner automatically mines without asm mode regardless -asm is set to 1 or to 0. In this case I can not profit with asm mode gains.
Please check it. I Have 5 RX480-s running under windows 10 OS.
Thanks in advance.

henz46

newbie

Activity: 24

Merit: 0

After i move to v.9 my rig is suddenly shut down at 4 minutes after mining, then i show off cable of psu an then on again, then my rig is start mining again then shut down again, then i show on again cable of psu then can mining as usual. Anyone have solution? Must i change my psu to 1000w or can i use powlim?
My psu is corsair gold+ 850w with 4x vga sapphire rx 470 4gb

Teress

full member

Activity: 224

Merit: 102

Quote from: miner582 on April 08, 2017, 02:55:31 PM

Quote from: fittsy on April 08, 2017, 01:11:37 PM

Quote from: mikbal on April 08, 2017, 09:50:02 AM

I reverted back to -asm 0. Many of my cards (rx470 and rx480 modded bioses from all brands) were fluctuating. This resultted in about %10 decrease in effective hashrate.

Increase power limit doesnt work.
Higher or lower dcri reduces fluctuating (doesnt end it). But my profits are reduced compared to -asm 0.
Higher cpu priority had no effect.

So i m actively monitoring this thread to increase my decred hashrate %60 again

Do not look within claymore to figure out if you actually had reduced profits. Look at the pool. Show us pool charts showing you had 10% less hashrate overtime.

at pool asm 0:

http://imgur.com/a/ErurZ

at pool asm 1:

http://imgur.com/a/mos7k

The black line is the speed reported by claymore. Maybe it is not 10% but definitly is not as stable as asm1, this graphic is for two 6xrx480 rig under claymore dual eth+dcr

Claymore can't connect to Nanopool with -esm 1. How did you do that? What is yout .bat settings?

evakka

sr. member

Activity: 700

Merit: 265

Quote from: Yerba on April 09, 2017, 06:09:11 AM

Bat command doesnt help you further. You must change cards bios.

Quote from: evakka on April 09, 2017, 05:28:30 AM

Can someone please post a sample bat command for ETH-only for version 9.0.

The 6xGPUs are the XFX RX 480 8GB with original bios and now are getting 24,8xx Mh/s each one on ethereum.
The PSU is an rose will 1500watt and I don't care about power consumption,

I would like to have the optimal performance

Thanks

Thanks a lot Yerba
Do you have any bios suggestions for these cards?
Shall I try do it with MSI afterburner?

Yerba

member

Activity: 146

Merit: 10

Quote from: Teress on April 09, 2017, 06:37:31 AM

I don't understand two things. During last 3 month I tried almost all pools (with different difficulties), miners, settings... Claymore shows now in v9 88.5 MHs from my 3 GPUs. On all pools I am getting always about 10-15% less hashpower (24 hours average) then miner shows. IS IT NORMAL? Do you have it too? I don't need milion MHs accepted, I just want some pool will give me result in hashrate I really have. I know stale shares are 1-5% sometimes, but still it is not reason for 10-15% less hashpower. Why is that? I've got ZERO incorrect shares.

Also for example during 5 minutes I have 15 accepted shares, but another 5 minutes I have no accepted shares. Why is that not always for example 1 share in 45 seconds?

Miner software fee, pool fee, some network packet losses.. ever tought about it also?

Teress

full member

Activity: 224

Merit: 102

I don't understand two things. During last 3 month I tried almost all pools (with different difficulties), miners, settings... Claymore shows now in v9 88.5 MHs from my 3 GPUs. On all pools I am getting always about 10-15% less hashpower (24 hours average) then miner shows. IS IT NORMAL? Do you have it too? I don't need milion MHs accepted, I just want some pool will give me result in hashrate I really have. I know stale shares are 1-5% sometimes, but still it is not reason for 10-15% less hashpower. Why is that? I've got ZERO incorrect shares.

Also for example during 5 minutes I have 15 accepted shares, but another 5 minutes I have no accepted shares. Why is that not always for example 1 share in 45 seconds?

Yerba

member

Activity: 146

Merit: 10

Bat command doesnt help you further. You must change cards bios.

Quote from: evakka on April 09, 2017, 05:28:30 AM

Can someone please post a sample bat command for ETH-only for version 9.0.

The 6xGPUs are the XFX RX 480 8GB with original bios and now are getting 24,8xx Mh/s each one on ethereum.
The PSU is an rose will 1500watt and I don't care about power consumption,

I would like to have the optimal performance

Thanks

Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 961. (Read 6590718 times)