Topic: [CLOSED] 1THs 1kW 28nm Miner - $4200 - March 18th, BTC, Wire, Paypal - Last Call - page 6. (Read 12947 times)
March 19, 2014, 08:43:57 PM
PM'd, thanks for offering.
March 19, 2014, 08:29:22 PM
I'll ask here just in case anyone else needs the info. For the bus connector, is the following links correct? They call them 10-pin Female Connector IDC Ribbon Cable Thanks, DW
http://www.seeedstudio.com/depot/Electronic-brick-10-pin-colorful-ribbon-cable-with-25-IDC-connector-p-484.html
http://szpowerpace.manufacturer.globalsources.com/si/6008838276924/pdtl/Flat-cable/1075193071/10-pin-Female-Connector-IDC-Ribbon-Cable.htm
http://www.seeedstudio.com/depot/Electronic-brick-10-pin-colorful-ribbon-cable-with-25-IDC-connector-p-484.html
http://szpowerpace.manufacturer.globalsources.com/si/6008838276924/pdtl/Flat-cable/1075193071/10-pin-Female-Connector-IDC-Ribbon-Cable.htm
YES
March 19, 2014, 08:06:29 PM
Any update on shipping?
You will have shipping info as soon as I have it... Unless it shows up after midnight eastern, in which case I will send it when I wake st 5:30a.No rush, just wanted to see if you got any updates. Didnt wanna hear tomorrow that they are delayed.
March 19, 2014, 08:05:59 PM
I'll ask here just in case anyone else needs the info. For the bus connector, is the following links correct? They call them 10-pin Female Connector IDC Ribbon Cable Thanks, DW
http://www.seeedstudio.com/depot/Electronic-brick-10-pin-colorful-ribbon-cable-with-25-IDC-connector-p-484.html
http://szpowerpace.manufacturer.globalsources.com/si/6008838276924/pdtl/Flat-cable/1075193071/10-pin-Female-Connector-IDC-Ribbon-Cable.htm
http://www.seeedstudio.com/depot/Electronic-brick-10-pin-colorful-ribbon-cable-with-25-IDC-connector-p-484.html
http://szpowerpace.manufacturer.globalsources.com/si/6008838276924/pdtl/Flat-cable/1075193071/10-pin-Female-Connector-IDC-Ribbon-Cable.htm
March 19, 2014, 07:05:25 PM
Quote from: (My supplier)
What you do with the leftovers is none of my business 
Regards
Chai
Regards
Chai
In respect for Cheshyr, this is his GB thread, if you´re interested send me a PM.
I´m also confident bobsag3´s supplier can shake down some boards in the nearest future
March 19, 2014, 06:48:01 PM
Any update on shipping?
You will have shipping info as soon as I have it... Unless it shows up after midnight eastern, in which case I will send it when I wake st 5:30a. March 19, 2014, 06:36:28 PM
If new units are 4 slots occupied 1 slot empty. Thats only good. Extra psu and easy to upgrade these to be 1,25TH miners.
Need to find source to buy these extra blades.
Need to find source to buy these extra blades.
March 19, 2014, 06:19:28 PM
I have yet to find a source for the individual blades, and my vendor is being rather unhelpful.
I have gotten single replacements from one of my vendors- I can ask him if we can get some single blades.
March 19, 2014, 06:08:28 PM
I´m not "officially" allowed to re-sell the spare parts right now guys.
If Cheshyr can´t find some one i can try to talk to my supplier.
1T25 Ver. 1.1 8xA1 is the model you want.
If Cheshyr can´t find some one i can try to talk to my supplier.
1T25 Ver. 1.1 8xA1 is the model you want.
I report i wish to buy blades too.
March 19, 2014, 05:40:01 PM
Any update on shipping?
March 19, 2014, 03:29:03 PM
Odd. It look like they designed it for multiphase, but decided not to use one of the FETs on each rail.
Yeah, and check the JTAG
Dragon miner is chaos PCB wise, but they work.
March 19, 2014, 03:23:21 PM
Odd. It look like they designed it for multiphase, but decided not to use one of the FETs on each rail.
March 19, 2014, 03:19:01 PM
I´m not "officially" allowed to re-sell the spare parts right now guys.
If Cheshyr can´t find some one i can try to talk to my supplier.
1T25 Ver. 1.1 8xA1 is the model you want.
If Cheshyr can´t find some one i can try to talk to my supplier.
1T25 Ver. 1.1 8xA1 is the model you want.
March 19, 2014, 03:09:06 PM
I'm totally cool with buying blades from JD if he can supply them.
March 19, 2014, 03:00:16 PM
Thank you! Did you lose any dragons while tweaking them?
No units, but 2 blades.
...and you´re welcome guys
Any luck getting single blades to replace them?
From the photos I'm seeing around, it looks like the mining controller will handle 6 blades, so if there's a way to get extras that might be helpful to those of us who will be receiving 32-chip miners.
The 32 chip version is 4 blades. The MCU can handle 8 units, only ports for 6, together with the pi.
I don´t know how the manufacturer handle warranty for you guys but i´m a bulk buyer so i get extra blades to avoid expensive RMA shipping (My deal says that the vendor is responsible for all shipping cost when it comes to RMA and warranty).
I wasn't thinking warranty, I was thinking more along the lines of buying another card or two and upping the power to get 1.2-1.4 TH/s.
Fully doable, just connect the blade/blades to the MCU and power (If you got the 2x650w version just plug in PCI-E connector/connectors) and lay it/them down on the plexi glas area. Runs a little bit hotter then the other blades, like 2-3 degrees. 32 chip version + extra blade/blades = Adjust clock setting to 850Mhz to be on the safe side.
I want to order 8 more blades to put into the 4 machines i ordered to give me a total of 6 per unit. Anyone know if we can order the blade separately?
Cheshyr is getting stonewalled by the vendor, sounds like they want to sell whole units only. Maybe one of the other resellers or bulk buyers?
March 19, 2014, 02:59:47 PM
Ya, JD hook us up with some blades and maybe a few joints..
March 19, 2014, 02:58:51 PM
I have yet to find a source for the individual blades, and my vendor is being rather unhelpful.
Maybe we can buy them from Jointdoctor
March 19, 2014, 02:55:48 PM
Thank you! Did you lose any dragons while tweaking them?
No units, but 2 blades.
...and you´re welcome guys
Any luck getting single blades to replace them?
From the photos I'm seeing around, it looks like the mining controller will handle 6 blades, so if there's a way to get extras that might be helpful to those of us who will be receiving 32-chip miners.
The 32 chip version is 4 blades. The MCU can handle 8 units, only ports for 6, together with the pi.
I don´t know how the manufacturer handle warranty for you guys but i´m a bulk buyer so i get extra blades to avoid expensive RMA shipping (My deal says that the vendor is responsible for all shipping cost when it comes to RMA and warranty).
I wasn't thinking warranty, I was thinking more along the lines of buying another card or two and upping the power to get 1.2-1.4 TH/s.
Fully doable, just connect the blade/blades to the MCU and power (If you got the 2x650w version just plug in PCI-E connector/connectors) and lay it/them down on the plexi glas area. Runs a little bit hotter then the other blades, like 2-3 degrees. 32 chip version + extra blade/blades = Adjust clock setting to 850Mhz to be on the safe side.
I want to order 8 more blades to put into the 4 machines i ordered to give me a total of 6 per unit. Anyone know if we can order the blade separately?
March 19, 2014, 02:53:22 PM
I have yet to find a source for the individual blades, and my vendor is being rather unhelpful.
March 19, 2014, 02:52:39 PM
It is very helpful. Can you tell me the default username and password.
Jump to: