Topic: [CLOSED] Prisma 1.4Th/s group buy @ 1.42 btc with coupon - page 2. (Read 21211 times)
I sent a message to phasebird for clarification, waiting for him to respond... I think the best way for you to take advantage of this is to follow his direct instructions... I can not handle several of their points wrt to replacement boards and actual refund sending. They haven't sent me any btc for refunds and supposedly some boards were shipped but a limited number, it won't be enough.
Waiting for the official instructions from Canary on how to proceed with this: https://bitcointalksearch.org/topic/m.9716544
I also have 4 bad boards on my unit. Please let me know how we can take advantage of this service - should we do this individually, or is there going to be a way to aggregate this since you were the original purchaser. Thanks!
Waiting for the official instructions from Canary on how to proceed with this: https://bitcointalksearch.org/topic/m.9716544
Same here.
I have a prisma with 4 bad boards. The most it has ever hashed is ~300 gh/s and that is for about 30 min. The prisma is sitting in a room collecting dust since it arrived.
Waiting for the official instructions from Canary on how to proceed with this: https://bitcointalksearch.org/topic/m.9716544
How many out of 10 you got in this batch?
Atm 1/10 are in.I am getting 2 Prismas + 1 Tube from Canary tomorrow (Monday). If anyone is interested, I can send them out within 24 hours for 1.42 BTC for each Prisma and 0.81142857 BTC for the Tube (what I paid for them). I will even pay for UPS ground myself (any other shipping is more expensive that it is worth). I am not sure what controller shipped with them, but I believe it is the USB adapter. I also have an imaged Pi from CG's group buy and the stand alone controller if people are interested in those. I will sell those at cost as well.
If anyone wants equipment to ship tomorrow (with free shipping) and not have to wait, let me know. Also, please make sure any payment request PMs are coming from me and not a similar looking name!
They are sold, thanks folks!!
How many out of 10 you got in this batch?
Atm 1/10 are in.0.81142857 BTC for the Tube
I can't pay what you're asking for the tube, but if you don't get your asking price I have a slot for one more.
How many out of 10 you got in this batch?
Atm 1/10 are in.I am getting 2 Prismas + 1 Tube from Canary tomorrow (Monday). If anyone is interested, I can send them out within 24 hours for 1.42 BTC for each Prisma and 0.81142857 BTC for the Tube (what I paid for them). I will even pay for UPS ground myself (any other shipping is more expensive that it is worth). I am not sure what controller shipped with them, but I believe it is the USB adapter. I also have an imaged Pi from CG's group buy and the stand alone controller if people are interested in those. I will sell those at cost as well.
If anyone wants equipment to ship tomorrow (with free shipping) and not have to wait, let me know. Also, please make sure any payment request PMs are coming from me and not a similar looking name!
How many out of 10 you got in this batch?
Atm 1/10 are in. 
How many out of 10 you got in this batch?
Just sent 1.42 your way Canary. Thank you and also thanks for honoring CrazyGuys deal with me. Here is the blockchain info https://blockchain.info/tx/27e1cd0e97cf28fb6bc9df34f120c6be62ff09569790f42a47f4fceb9cd1b07c
thanks! I'll get it transmitted when they're ready.
Just sent 1.42 your way Canary. Thank you and also thanks for honoring CrazyGuys deal with me. Here is the blockchain info https://blockchain.info/tx/27e1cd0e97cf28fb6bc9df34f120c6be62ff09569790f42a47f4fceb9cd1b07c
Hi All,
First Thank You Canary for doing the group buy!
Has anyone noticed that running these on the USB Controller is highly unstable?
I have two of my three units so far and both are highly unstable. I can not get them to keep up at anywhere near 1.4Ths. I can get them to run, but they drift all over the place from 600Ghs to an occasional burst at 1.5Ths.
I have tried running them on the RPi and the CubieTruck. I have used the stock 4.7.0 CGminer, Fixed Debian Build of 4.7.0-1 CGminer, and the BlockErupter 4.6.1 build of CGminer from GitHub. None have fixed or even made improvements. I have tried both the standard (no --bet-clk option) and --bet-clk=23 timing.
One thing I have noticed is that there is a lot of extended output in the BlockErupter Controller, that shows the chip status. Can we get that status from CGminer somehow?
First Thank You Canary for doing the group buy!
Has anyone noticed that running these on the USB Controller is highly unstable?
I have two of my three units so far and both are highly unstable. I can not get them to keep up at anywhere near 1.4Ths. I can get them to run, but they drift all over the place from 600Ghs to an occasional burst at 1.5Ths.
I have tried running them on the RPi and the CubieTruck. I have used the stock 4.7.0 CGminer, Fixed Debian Build of 4.7.0-1 CGminer, and the BlockErupter 4.6.1 build of CGminer from GitHub. None have fixed or even made improvements. I have tried both the standard (no --bet-clk option) and --bet-clk=23 timing.
One thing I have noticed is that there is a lot of extended output in the BlockErupter Controller, that shows the chip status. Can we get that status from CGminer somehow?
Try pointing them at a pool port set for difficulty 2048 (S4).
I seen issues when when it comes to pool port set to vardif - units would hash for 1-1.25 hours then stop hashing - when this happen the difficulty would drop below 500 then bottom out and stop hashing till BE Controller was rebooted; had a similar experience on the RPi except it managed to hash for about 2.5hrs before dropping out. Since I changed to pool port set to 2048 it has been going non-stop for over 21.5 hrs.
I currently have 2 prisma using CG Minera Rpi image - with AM CGminer fork - running great. When I used the BE Controller the I could only have 7 of the 8 hashboards going - if I tried all 8 - one of the boards didn't work 85% of the time and had chips on 1 board go into PwrDn state (around 13 on both physical & logical blade).
Screenshots below are pool report hashrate, minera, & CGMiner output. The drop in hash around 5pm seems to be pool or internet related as my 10 S3s also experienced a drop at the same time.
http://i.imgur.com/yxqjoou.png
http://i.imgur.com/HZNK8CT.png
http://i.imgur.com/9tBewQm.png
Hi All,
First Thank You Canary for doing the group buy!
Has anyone noticed that running these on the USB Controller is highly unstable?
I have two of my three units so far and both are highly unstable. I can not get them to keep up at anywhere near 1.4Ths. I can get them to run, but they drift all over the place from 600Ghs to an occasional burst at 1.5Ths.
I have tried running them on the RPi and the CubieTruck. I have used the stock 4.7.0 CGminer, Fixed Debian Build of 4.7.0-1 CGminer, and the BlockErupter 4.6.1 build of CGminer from GitHub. None have fixed or even made improvements. I have tried both the standard (no --bet-clk option) and --bet-clk=23 timing.
One thing I have noticed is that there is a lot of extended output in the BlockErupter Controller, that shows the chip status. Can we get that status from CGminer somehow?
First Thank You Canary for doing the group buy!
Has anyone noticed that running these on the USB Controller is highly unstable?
I have two of my three units so far and both are highly unstable. I can not get them to keep up at anywhere near 1.4Ths. I can get them to run, but they drift all over the place from 600Ghs to an occasional burst at 1.5Ths.
I have tried running them on the RPi and the CubieTruck. I have used the stock 4.7.0 CGminer, Fixed Debian Build of 4.7.0-1 CGminer, and the BlockErupter 4.6.1 build of CGminer from GitHub. None have fixed or even made improvements. I have tried both the standard (no --bet-clk option) and --bet-clk=23 timing.
One thing I have noticed is that there is a lot of extended output in the BlockErupter Controller, that shows the chip status. Can we get that status from CGminer somehow?
Ive been out of buying new hardware for the past month. Any rumors of price drops?
no rumors of price drop as of this moment. i'll be able to transmit an order next week. there's no inventory to ship right now.
Ive been out of buying new hardware for the past month. Any rumors of price drops?
EU shipping?
it's domestic only 
EU shipping?
Are these still available?
As a group buy, yes, once I get 10 units ordered, I'll forward to AM.
Are these still available?
If you haven't sent me a label yet, please do so... I'll be shipping out tomorrow
Jump to: