Pages:
Author

Topic: [CLOSED]Minion Chip Assembly GB - page 18. (Read 77573 times)

full member
Activity: 238
Merit: 106
September 16, 2014, 09:41:07 AM
I'm an EU batch1 order and my TechnoBit status just changed to shipped. Smiley
member
Activity: 94
Merit: 10
September 16, 2014, 09:31:00 AM
Are we still just on batch 1?
Qeu
full member
Activity: 120
Merit: 100
September 16, 2014, 05:53:44 AM
So this is our design fail.
As far we were using the intel 1150 adapter of the freezer we missed that the outer edge dim is for 2011.
So I look over the coolers.
The intel stock ones will need 4 small brackets and Zelman and ice edge types ( AMD standrt attachment) will need modified brackets , that is easier.

I'm going to get samples in the morning in order to check adapting parts
We may be able to do without for the standard intel ones, I can bent those push-pin holders easily a couple of mm to get to 80mm. Hope you can fit one on a board and save on extra work.
The deepcool ice edge mini fs has an intel 115x plastic mount with push-pins only, but a metal frame that screws on to that and holds the sink. So who sells loose amd cooler sockets...

I'm also sat on a little pile of Intel coolers and this is making me a little nervous, but not as nervous as not knowing where I am in the queue (Batch1, direct within EU, x2). Can you keep us updated with some pics if you get yours to fit Qeu?
Sure I will, but since Bobsag3 tried the standard Intel one and said it doesn't fit, it may be better to report to Marto right away and get an adaption fix sent with your miners. Plus I don't think I will see the miners this week, or sooner than you will see yours, nobody in EU seems to have his order marked as shipped.
sr. member
Activity: 291
Merit: 250
Scam-Busting PSA: Beware of Black Arrow Software
September 16, 2014, 05:38:33 AM
So this is our design fail.
As far we were using the intel 1150 adapter of the freezer we missed that the outer edge dim is for 2011.
So I look over the coolers.
The intel stock ones will need 4 small brackets and Zelman and ice edge types ( AMD standrt attachment) will need modified brackets , that is easier.

I'm going to get samples in the morning in order to check adapting parts
We may be able to do without for the standard intel ones, I can bent those push-pin holders easily a couple of mm to get to 80mm. Hope you can fit one on a board and save on extra work.
The deepcool ice edge mini fs has an intel 115x plastic mount with push-pins only, but a metal frame that screws on to that and holds the sink. So who sells loose amd cooler sockets...

I'm also sat on a little pile of Intel coolers and this is making me a little nervous, but not as nervous as not knowing where I am in the queue (Batch1, direct within EU, x2). Can you keep us updated with some pics if you get yours to fit Qeu?
newbie
Activity: 18
Merit: 0
September 15, 2014, 07:42:31 PM
Marto - Can you please give us an update on sending the customer list to Minersource for batch 1 customers?  I asked this same question almost 24 hours ago and it went unanswered.  Please let us know where you are at with this list because these delays are really hurting our ROI on these boards.
hero member
Activity: 686
Merit: 500
September 15, 2014, 06:58:04 PM
So this is our design fail.
As far we were using the intel 1150 adapter of the freezer we missed that the outer edge dim is for 2011.
So I look over the coolers.
The intel stock ones will need 4 small brackets and Zelman and ice edge types ( AMD standrt attachment) will need modified brackets , that is easier.

I'm going to get samples in the morning in order to check adapting parts

 No parts needed. I ordered exactly what you said, over $4k dollars in fans, and they collectiong dust. Please update me on my order status. Marto, I want to believe, but as I was one of the first to send chips, I need to start seeing results please!

full member
Activity: 238
Merit: 106
September 15, 2014, 06:30:58 PM
You can leave the sheet metal brackets on for me.

What about other European GroupBuy1 orders? Estimated shipping?
legendary
Activity: 910
Merit: 1000
September 15, 2014, 05:34:29 PM
Heres some pics of what we got:




Problem though.
Although the board advertises that it will work with all intel 1150 coolers, it does not. We have tried several coolers so far, and none fit into the mounting holes on the board, or the weird metal brackets included.

Crossing my fingers that 3 of those are mine!!!!
sr. member
Activity: 407
Merit: 255
September 15, 2014, 04:54:55 PM
So this is our design fail.
As far we were using the intel 1150 adapter of the freezer we missed that the outer edge dim is for 2011.
So I look over the coolers.
The intel stock ones will need 4 small brackets and Zelman and ice edge types ( AMD standrt attachment) will need modified brackets , that is easier.

I'm going to get samples in the morning in order to check adapting parts
We may be able to do without for the standard intel ones, I can bent those push-pin holders easily a couple of mm to get to 80mm. Hope you can fit one on a board and save on extra work.
The deepcool ice edge mini fs has an intel 115x plastic mount with push-pins only, but a metal frame that screws on to that and holds the sink. So who sells loose amd cooler sockets...

Marto correct me if I am wrong but the intel 1150x sits too low for your board without the 4 small brackets to raise them? I remember him saying that the BA chip is thicker than a intel chip?
Qeu
full member
Activity: 120
Merit: 100
September 15, 2014, 04:42:01 PM
So this is our design fail.
As far we were using the intel 1150 adapter of the freezer we missed that the outer edge dim is for 2011.
So I look over the coolers.
The intel stock ones will need 4 small brackets and Zelman and ice edge types ( AMD standrt attachment) will need modified brackets , that is easier.

I'm going to get samples in the morning in order to check adapting parts
We may be able to do without for the standard intel ones, I can bent those push-pin holders easily a couple of mm to get to 80mm. Hope you can fit one on a board and save on extra work.
The deepcool ice edge mini fs has an intel 115x plastic mount with push-pins only, but a metal frame that screws on to that and holds the sink. So who sells loose amd cooler sockets...
sr. member
Activity: 504
Merit: 250
September 15, 2014, 04:07:07 PM
Marto shit happens you still have done a great job with these boards.
hero member
Activity: 728
Merit: 500
September 15, 2014, 04:04:35 PM
So this is our design fail.
As far we were using the intel 1150 adapter of the freezer we missed that the outer edge dim is for 2011.
So I look over the coolers.
The intel stock ones will need 4 small brackets and Zelman and ice edge types ( AMD standrt attachment) will need modified brackets , that is easier.

I'm going to get samples in the morning in order to check adapting parts
Qeu
full member
Activity: 120
Merit: 100
September 15, 2014, 02:58:09 PM
LGA1150, LGA1155, LGA1156, all have 75mm distance between the socket holes.  Huh All coolers made for these sockets use the 75 mm. did you use an AMD frame from the Arctic Cooling Freezer 7 Pro's box to determine your holes?

I see no updates in my technobit account regarding shipping, which would happen Friday or today?Any tracking code to share?

I have 48 of these I need adaption for, http://www.pugetsystems.com/parts/CPU-Cooling/Stock-Intel-115x-CPU-Fan-6414,
32 of these http://www.deepcool.com/product/cpucooler/2013-12/7_120.shtml

Bobsag3, still nobody available to tell me by pm where that refund check went/is now?
sr. member
Activity: 504
Merit: 250
September 15, 2014, 02:53:53 PM
Well i almost bought a lot of coolers that weren't artic but since i was able to get a deal from Pistachio here he saved my ass. He may still have some left if other need them, in the mean time i got 400gh worth of antminers for about 120$ and they've been pumping away Tongue .

i just got a antminer also for some extra ghs
sr. member
Activity: 504
Merit: 250
September 15, 2014, 02:52:36 PM
Damn not good from the specs that would make them socket 2011 not 1150 Sad
sr. member
Activity: 374
Merit: 250
September 15, 2014, 02:36:18 PM



INTEL 1155 and 1150



INTEL 2011



Looks like a mistake Martin.. 80mm hole spacing is the same as a socket 2011 cooler
hero member
Activity: 728
Merit: 500
September 15, 2014, 01:07:45 PM
For the zalman
I have similar model of evercool here that is originally for AMD and circle plastic adapter for Intel.
I'll try to make a set of 8 sheetmetal brackets with hinge for the AMD style attachment and ship it to minersource for testing  witht he next sending
hero member
Activity: 728
Merit: 500
September 15, 2014, 01:03:51 PM
But wouldn't all 1150 coolers have the legs in the same place with only a slight variance.
Yes but we do not use clips , but screws that fit in to treaded holes in the base heatsink.
SO there is no gap while cliping.
Excuse my English here
sr. member
Activity: 407
Merit: 255
September 15, 2014, 01:03:30 PM
actualy they are 80mm pitch
We have only one model here localy that we bought and was diferent - it is some evercool.
Anyway with all this troubles with production this is the easy one.
If you pre-bought quontity or have one of a choise , just give the model and I'll adopt it.
best solution from my point of view .
We got arctic freezer 7 from the beginning 3 months back and design it with it.
Honestly never cross checked with other vendors coolers .
Board redesign is not doable solution now.
So we'll produce for you any adapter you will need for free.
My non-bitcoin job is mechanical design and tooling production so it is easy part for me

I was going to use the ZALMAN CNPS5X. If you can build an adapter for this that would be great. Otherwise I might be able to use zip ties and lock them down this way since it has a clip that would hold down the cooler to the mount.
 
sr. member
Activity: 504
Merit: 250
September 15, 2014, 12:59:42 PM
But wouldn't all 1150 coolers have the legs in the same place with only a slight variance.
Pages:
Jump to: