Topic: [CLOSING DOWN] ScryptGuild Auto-Switching Pool - page 42. (Read 102282 times)
let me ask this question .. what is acceptable for HW errors. because if i bring intensity up then hash rate will go up but i get HW errors. at i 13 i get 0 HW errors no matter how long they hash.
aztec if you use an headless asus 290x try these out
"api-listen" : true,
"intensity" : "20",
"vectors" : "1",
"worksize" : "256",
"kernel" : "scrypt",
"auto-fan" : true,
"temp-cutoff" : "85",
"temp-overheat" : "75",
"temp-target" : "70",
"expiry" : "30",
"gpu-dyninterval" : "7",
"log" : "5",
"queue" : "1",
"retry-pause" : "5",
"scan-time" : "30",
"scrypt" : true,
"temp-hysteresis" : "3",
"shares" : "0",
"shaders" : "2816",
"thread-concurrency" : "32765",
"gpu-thread" : "1",
"gpu-engine" : "920",
"sharethreads" : "32",
"lookup-gap" : "2",
"gpu-powertune" : "20",
"gpu-memclock" : "1500"
}
"api-listen" : true,
"intensity" : "20",
"vectors" : "1",
"worksize" : "256",
"kernel" : "scrypt",
"auto-fan" : true,
"temp-cutoff" : "85",
"temp-overheat" : "75",
"temp-target" : "70",
"expiry" : "30",
"gpu-dyninterval" : "7",
"log" : "5",
"queue" : "1",
"retry-pause" : "5",
"scan-time" : "30",
"scrypt" : true,
"temp-hysteresis" : "3",
"shares" : "0",
"shaders" : "2816",
"thread-concurrency" : "32765",
"gpu-thread" : "1",
"gpu-engine" : "920",
"sharethreads" : "32",
"lookup-gap" : "2",
"gpu-powertune" : "20",
"gpu-memclock" : "1500"
}
hmmm.. something happened. the memory speed is stuck at 150 and wont change now which causing my hash rate to plummet to about 125 k/hs. anyway to fix this so the memory is back to 1500 ??
Driver crash? Might need to restart the PC to fix it.
M
i deleted cgminer and replaced it and now is working. gonna try ur settings again. however i tried before and still got 525 k/hs ?? i am try again.
Check out this thread:
http://www.reddit.com/r/litecoinmining/comments/1vb3eb/asus_r9_290_mining_configurations_cgminer/
M
hmmm.. something happened. the memory speed is stuck at 150 and wont change now which causing my hash rate to plummet to about 125 k/hs. anyway to fix this so the memory is back to 1500 ??
Driver crash? Might need to restart the PC to fix it.
M
i deleted cgminer and replaced it and now is working. gonna try ur settings again. however i tried before and still got 525 k/hs ?? i am try again.
hmmm.. something happened. the memory speed is stuck at 150 and wont change now which causing my hash rate to plummet to about 125 k/hs. anyway to fix this so the memory is back to 1500 ??
Driver crash? Might need to restart the PC to fix it.
M
Charts all well and good, I was mining 10Mh of scrypt to ScryptGuild last night and it never reported more than 5.5Mh
Whats the deal with this pool?
45% skim off the top?
Actually I think the algorithm that Eleuthria uses is 5% off the top, 20% off the bottom and two 10% bits out of the middle somewhere. He's pretty crafty like that.Whats the deal with this pool?
45% skim off the top?
That would explain the holes in my data
Charts all well and good, I was mining 10Mh of scrypt to ScryptGuild last night and it never reported more than 5.5Mh
Whats the deal with this pool?
45% skim off the top?
Actually I think the algorithm that Eleuthria uses is 5% off the top, 20% off the bottom and two 10% bits out of the middle somewhere. He's pretty crafty like that. Whats the deal with this pool?
45% skim off the top?
it could be local HW errors will reduce some hashing rate, or stales can reduce hashing rate too . at least that what i have noticed. one day i will figure out how to get my r9 290x's to hash more than 500 k/hs without massive HW errors or stales .
You have 290x's that aren't being properly used? I feel bad for you man. That's like owning a Porsche and knowing how to drive it.
Seriously, what's your setup? memory speed? GPU speed? command line settings for cg/sgminer? What model of 290x? I think you should be able to get 800kh/s+ from them. I looked long and hard at the GPUs before settling on my 280s. Would have liked to stock up on 290s instead of 280s, but 280s seemed to be most cost effective.
M
yeah i been having hard time figuring out what i need to do to get these ASUS cards hashing faster: (i get no HW errors at all with this settings running at 72 - 73 degrees)
cgminer -o stratum+tcp://stratum.scryptguild.com:3333 -u aztecminer -p 123 --scrypt -I 13 -w 256 --thread-concurrency 8192
if i up the intensity to 14 i get HW errors. if i change the thread concurrency to 32765 and cgminer wont start it gives me an error. i will try work on it some more because i know i should get more from these two cards. i dont know the memory speed or gpu speed atm. how do i find this in cgminer ?? is [G] ?? thanks!
edit: i think it says E: 1000Mhz and M: 1250Mhz (if this is the right settings to look at)
edit2: i changed E: 1000 and M: 1500 and P: 20 ............... i still getting 525 k/hs from each card w temps at 73 - 74.
Try E=950 and M=1500, get rid of -W in your command line settings.
This is what I use for my Asus 280x:
--scrypt -I 13 -g 2 --thread-concurrency 8192
running at E=1080 memory=1500
M
hmmm.. something happened. the memory speed is stuck at 150 and wont change so i had to reload cgminer and start over. i try ur settings and still got 525 k/hs.
I have 30 Gridseed Miners running on BFGminer producing 10Mh that appears to be sending to SG yet the pool is reporting 5.5Mh
It could be a million things so I am going to play with cgminer and CPU miner this weekend.
It could be a million things so I am going to play with cgminer and CPU miner this weekend.
I haven't used any of those Gridseed miners yet. If they are 300kh/s a piece, times 30, that's 9MH/s. Not sure how/why BFG is saying 10.
You can try pointing them at another scrypt pool and see what that pool reports.
M
They are 330-350kh each which is 9.9 to 10.5 Mh
it could be local HW errors will reduce some hashing rate, or stales can reduce hashing rate too . at least that what i have noticed. one day i will figure out how to get my r9 290x's to hash more than 500 k/hs without massive HW errors or stales .
You have 290x's that aren't being properly used? I feel bad for you man. That's like owning a Porsche and knowing how to drive it.
Seriously, what's your setup? memory speed? GPU speed? command line settings for cg/sgminer? What model of 290x? I think you should be able to get 800kh/s+ from them. I looked long and hard at the GPUs before settling on my 280s. Would have liked to stock up on 290s instead of 280s, but 280s seemed to be most cost effective.
M
yeah i been having hard time figuring out what i need to do to get these ASUS cards hashing faster: (i get no HW errors at all with this settings running at 72 - 73 degrees)
cgminer -o stratum+tcp://stratum.scryptguild.com:3333 -u aztecminer -p 123 --scrypt -I 13 -w 256 --thread-concurrency 8192
if i up the intensity to 14 i get HW errors. if i change the thread concurrency to 32765 and cgminer wont start it gives me an error. i will try work on it some more because i know i should get more from these two cards. i dont know the memory speed or gpu speed atm. how do i find this in cgminer ?? is [G] ?? thanks!
edit: i think it says E: 1000Mhz and M: 1250Mhz (if this is the right settings to look at)
edit2: i changed E: 1000 and M: 1500 and P: 20 ............... i still getting 525 k/hs from each card w temps at 73 - 74.
Try E=950 and M=1500, get rid of -W in your command line settings.
This is what I use for my Asus 280x:
--scrypt -I 13 -g 2 --thread-concurrency 8192
running at E=1080 memory=1500
M
it could be local HW errors will reduce some hashing rate, or stales can reduce hashing rate too . at least that what i have noticed. one day i will figure out how to get my r9 290x's to hash more than 500 k/hs without massive HW errors or stales .
You have 290x's that aren't being properly used? I feel bad for you man. That's like owning a Porsche and knowing how to drive it.
Seriously, what's your setup? memory speed? GPU speed? command line settings for cg/sgminer? What model of 290x? I think you should be able to get 800kh/s+ from them. I looked long and hard at the GPUs before settling on my 280s. Would have liked to stock up on 290s instead of 280s, but 280s seemed to be most cost effective.
M
yeah i been having hard time figuring out what i need to do to get these ASUS cards hashing faster: (i get no HW errors at all with this settings running at 72 - 73 degrees)
cgminer -o stratum+tcp://stratum.scryptguild.com:3333 -u aztecminer -p 123 --scrypt -I 13 -w 256 --thread-concurrency 8192
if i up the intensity to 14 i get HW errors. if i change the thread concurrency to 32765 and cgminer wont start it gives me an error. i will try work on it some more because i know i should get more from these two cards. i dont know the memory speed or gpu speed atm. how do i find this in cgminer ?? is [G] ?? thanks!
edit: i think it says E: 1000Mhz and M: 1250Mhz (if this is the right settings to look at)
edit2: i changed E: 1000 and M: 1500 and P: 20 ............... i still getting 525 k/hs from each card w temps at 73 - 74.
I have 30 Gridseed Miners running on BFGminer producing 10Mh that appears to be sending to SG yet the pool is reporting 5.5Mh
It could be a million things so I am going to play with cgminer and CPU miner this weekend.
It could be a million things so I am going to play with cgminer and CPU miner this weekend.
I haven't used any of those Gridseed miners yet. If they are 300kh/s a piece, times 30, that's 9MH/s. Not sure how/why BFG is saying 10.
You can try pointing them at another scrypt pool and see what that pool reports.
M
it could be local HW errors will reduce some hashing rate, or stales can reduce hashing rate too . at least that what i have noticed. one day i will figure out how to get my r9 290x's to hash more than 500 k/hs without massive HW errors or stales .
You have 290x's that aren't being properly used? I feel bad for you man. That's like owning a Porsche and knowing how to drive it.
Seriously, what's your setup? memory speed? GPU speed? command line settings for cg/sgminer? What model of 290x? I think you should be able to get 800kh/s+ from them. I looked long and hard at the GPUs before settling on my 280s. Would have liked to stock up on 290s instead of 280s, but 280s seemed to be most cost effective.
M
Charts all well and good, I was mining 10Mh of scrypt to ScryptGuild last night and it never reported more than 5.5Mh
Whats the deal with this pool?
45% skim off the top?
Whats the deal with this pool?
45% skim off the top?
Working fine here.
M
Oh good well then nevermind, since it's ok for you then I should just deal with it.
Are you sure all your workers are pointing here? Are you sharing workers across rigs? Is your local hashrate report wrong? All sorts of things that could be awry here.
M
I have 30 Gridseed Miners running on BFGminer producing 10Mh that appears to be sending to SG yet the pool is reporting 5.5Mh
It could be a million things so I am going to play with cgminer and CPU miner this weekend.
Charts all well and good, I was mining 10Mh of scrypt to ScryptGuild last night and it never reported more than 5.5Mh
Whats the deal with this pool?
45% skim off the top?
Whats the deal with this pool?
45% skim off the top?
Working fine here.
M
Oh good well then nevermind, since it's ok for you then I should just deal with it.
Are you sure all your workers are pointing here? Are you sharing workers across rigs? Is your local hashrate report wrong? All sorts of things that could be awry here.
M
it could be local HW errors will reduce some hashing rate, or stales can reduce hashing rate too . at least that what i have noticed. one day i will figure out how to get my r9 290x's to hash more than 500 k/hs without massive HW errors or stales .
hmmm.. ok that looks right what u said .. so why the change ?? before i could see all the coins we potentially mine whether i had some those coins or not ?? now i only see the coins i have mined and not converted ??
You can see all the coins we potentially auto-mine on the Convert to BTC page, where it has the settings for your reserves of each coin if you wish to hang onto some.
yes thankyou i see that now. i am holding LTC in reserve just in case and auto convert the rest. I really like the guild. btcguild was first place i really mined btc and i am still there. this scryptguild replaced my alt coin mining operation where i was mining doge and sending to cryptsy to exchange myself . i think is much more profitable this way.
Charts all well and good, I was mining 10Mh of scrypt to ScryptGuild last night and it never reported more than 5.5Mh
Whats the deal with this pool?
45% skim off the top?
Whats the deal with this pool?
45% skim off the top?
Working fine here.
M
Oh good well then nevermind, since it's ok for you then I should just deal with it.
Are you sure all your workers are pointing here? Are you sharing workers across rigs? Is your local hashrate report wrong? All sorts of things that could be awry here.
M
Yeah no problems with my farm either as far as reporting goes. You did something wrong.
Charts all well and good, I was mining 10Mh of scrypt to ScryptGuild last night and it never reported more than 5.5Mh
Whats the deal with this pool?
45% skim off the top?
Whats the deal with this pool?
45% skim off the top?
Working fine here.
M
Oh good well then nevermind, since it's ok for you then I should just deal with it.
Charts all well and good, I was mining 10Mh of scrypt to ScryptGuild last night and it never reported more than 5.5Mh
Whats the deal with this pool?
45% skim off the top?
Whats the deal with this pool?
45% skim off the top?
Working fine here.
M
Jump to: