Topic: Dayun Zig Z1 - Lyra2Rev2 6.8GH/s Asic miner - page 3. (Read 42511 times)

I'll try to install tomorrow

I have several Zig Z1 pros hosted and they're nothing but a pain, with them randomly stopping and starting, and the hashrate being all over the place but averaging to be much lower than 13GHs.

Has anyone tried the updated firmware here and could let me know if it helps at all
https://www.cryptominerbros.com/solve-problem-zig-z1-pro-fix-dayun-zig-z1-pro-firmware-upgrade-firmware-update/

I'm using nicehash, do people find things to be more stable on other pools.

Tell me, please, bought Z1 pro, the hashrate jumps from 0-25, the hash board does not work periodically, it turns off

Does anybody know how to set this miner so when it loses power or you turn off with a wifi plug that it fires back up when power is back or turned back on with a smartplug?  I have to turn the power supply off with the switch on the power supply and back on and it will for up.

to those who owns a Pro version, here is my experience....

1) use the antminer IP reporter to get your IP address, i can see some people are having this problem.
2) APW7 only support 10A from what it can see on spec (120v / 220v). if you connect 120v, you will force the PSU to work %125 (1500watts / 120v = 12.5A). my ASIC is connected to 220v (1500watt / 220v = 6.81A), keep in mind that 220v will save electric bill.
3) better modify the PSU with 2 extra cable. on ebay I bought 2 cables, each cable has 6 heads. with this modification you will have 20 heads of 6pin and the miner will only require 17 heads. this will void using a splitter on each 6pin, using the splitter will burn it. trust me, i had that problem.
4) better use a high quality AC cable without adapter conversion. during the time will melt down the adapter.
5) you can mine in any pool that support lyra2v2, i did it on nicehash, ahashpool, zpool, miningpoolhub, vippool. can see some people couldn't do it.
6) PROP, PPS, PPLNS are used on those pools mentioned, if you don't know what it means, google it. i find out PROP is too risky due to the moving hash and it affect the luck, PPS pays less than PPLNS.
7) we all know that ASICs are plug & play, but you still have to do a lot of homework, so do it you bunch of lazy ass.

 By the way, i need 3 volunteers with PRO version to mine a specific pool. 4 of us will be mining for a week at the same time, so we can see which pool has a better profit.  

My guess is a short in the unit since swapping the PSU didn't fix the problem.

Does one of the settings set the miner to boot automatically when there is a power outage?  I can shut mine down by pulling the plug, but when plugging back in it will only start if I flip the switch off and back on.

Gday i have been having an odd problem with one of my 2 zig z1 miners. i have been running bitmain psu one apw7 and one apw3++ on the problem miner.


The apw7  started to trip my earth leakage breaker so was removed from service. The last week i have had the apw3++ set off the breaker in my power board adaptor (has a small lead and four plugs on it). I thought nothing of it until i went in and reset it a second time and noticed all the black pcie pins were cooked going to the hashboards. And one was so bad it was a fair effort to remove from the unit.

Basically i am wondering if this is the unit or a power supply issue as id rather not keep burning out power supplies. Also is it possible to change the pcie 6 pin males on the bitmain psu?

Should also mention i have had these miners for about a year now, And the second miner is perfect. Also I am in Australia so running 240v.


Any feedback or help is appreciated thanks.

is it

https://www.zigminer.com/

I found the link in my ZigZ1Pro

regards

what is the legit site?

brad

Hi,
I can only mine on Nicehash. I tried Zergpool, Ahashpool and Zpool. But after a while hash goes to 0. Nonce submit on/off makes no difference. Any ideas?
Thank you in advance.

how do you activate check nonce?

...hm do you have 2 PSU?

coz after I checked all the cables and added a 2nd PSU it is working fine!

I have the same problem, a board seems to be broken on the first start, after changing a miningpool, only 4 boards are active.
An update to the last image did not succeed.
Maybe one has a suggestion what I can try?

if you mine to nicehash activate the Check Nonce submit
else, leave it off. this will make performance degraded for other pools, and they don't require this nonce submit

Hi sunniest_solomin, I have bought two fans from a wholesaler, but they arrived without the connector. I also have my Dayun to a farm, so I can't check the PIN connector, that I think is a Molex.

Anyone know of a replacement fan for these units or at least what brand they use? One of mine is dead. They're 140mm so I can't just swap out any other spares from other ASICs. They're also 4 pin connectors? (My unit is at a colo so I can't see it first hand). 

Anyways, I can't find a replacement anywhere.

there:  https://drive.google.com/drive/folders/1RlYpFPwiR5JJlMqe8c3k1_c1_BknpwMN

I used the Hhotfix 07_05.
but I dont know what was fixed.... 😀
do you have issues?

Where can i find the patch for zig z1 pro?

Thanks badbart, i will try this way too!


Have a nice sunday
Vinncent