Dayun Zig Z1 - Lyra2Rev2 6.8GH/s Asic miner - page 56.

yrk1957

member

Activity: 531

Merit: 29

Quote from: kazall on October 05, 2018, 05:21:36 PM

Thanks for your help so far.

My network is 192.168.168.x

and it doesn't find anything connecting to 192.168.168.100 or 192.168.168.1

192.168.168.100 ? Are you sure?

kazall

newbie

Activity: 7

Merit: 0

Thanks for your help so far.

My network is 192.168.168.x

and it doesn't find anything connecting to 192.168.168.100 or 192.168.168.1

yrk1957

member

Activity: 531

Merit: 29

Quote from: kazall on October 05, 2018, 04:41:11 PM

Quote from: yrk1957 on September 28, 2018, 09:53:37 PM

I was able to get mine working by burning this firmware on a new USB stick:

https://drive.google.com/open?id=1z564S10Q3SWN8-8_HmreuUCQEI_gXYl9

Can you describe the steps? I burnt the firmware onto the USB and reset the machine with it plugged in. I no longer get the red light but I also can't find the miner on my IP scan anywhere.

Is there a way to directly plug into the miner?

If red light is off then it should be fine. By default it starts with fixed IP 192.168.1.100. So connect to that, assuming your network is 192.168.1.x based.

kazall

newbie

Activity: 7

Merit: 0

Quote from: yrk1957 on September 28, 2018, 09:53:37 PM

I was able to get mine working by burning this firmware on a new USB stick:

https://drive.google.com/open?id=1z564S10Q3SWN8-8_HmreuUCQEI_gXYl9

Can you describe the steps? I burnt the firmware onto the USB and reset the machine with it plugged in. I no longer get the red light but I also can't find the miner on my IP scan anywhere.

Is there a way to directly plug into the miner?

yrk1957

member

Activity: 531

Merit: 29

Quote from: Hitsxx on October 05, 2018, 03:39:15 PM

Quote from: Bitreo on October 04, 2018, 07:50:12 AM

if you want to modify the config files on the filesystem then you need to get the root password. if anyone can crack the password here is the hash :

Username: root
PW Hash: $6$pvnavTv2$2W/s.veJLVbb1g9qJpFO7ATNNBiOtwt.MXABU6nRVgJwuiS3WlBrRMj0avAdnHL

Username: fa
PW Hash: $6$muvIxroU$Lcuu06mrLbEONRLK312njB.RTI4dbC9QdJAZ6Bam0RnJpibRO2K62XHBKRKRo3U1IDFTtTAdXb/h.vp8vXuio1

regards

hash for root not full specified.

Here is the correct:

Code:

root:$6$pvnavTv2$2W/s.veJLVbb1g9qJpFO7ATNNBiOtwt.MXABU6nRVgJwuiS3WlBrRMj0avAdnHLt4XSfDBTyt52n7ORs.1hpj.

Decryption Result: root:envision

Use with pleasure.

Was that a multi-GPU attack? Just wondering.

Edit: NVM, straight up dictionary.

Hitsxx

newbie

Activity: 15

Merit: 2

Quote from: Bitreo on October 04, 2018, 07:50:12 AM

if you want to modify the config files on the filesystem then you need to get the root password. if anyone can crack the password here is the hash :

Username: root
PW Hash: $6$pvnavTv2$2W/s.veJLVbb1g9qJpFO7ATNNBiOtwt.MXABU6nRVgJwuiS3WlBrRMj0avAdnHL

Username: fa
PW Hash: $6$muvIxroU$Lcuu06mrLbEONRLK312njB.RTI4dbC9QdJAZ6Bam0RnJpibRO2K62XHBKRKRo3U1IDFTtTAdXb/h.vp8vXuio1

regards

hash for root not full specified.

Here is the correct:

Code:

root:$6$pvnavTv2$2W/s.veJLVbb1g9qJpFO7ATNNBiOtwt.MXABU6nRVgJwuiS3WlBrRMj0avAdnHLt4XSfDBTyt52n7ORs.1hpj.

Decryption Result: root:envision

Use with pleasure.

btc2017btc2017

member

Activity: 176

Merit: 10

I've been told that mining on Nicehash is the reason why the Z1 is unstable (unstable hash rates, and random daily crashes that requires a power cycle). I've been told that mining monacoin on f2pool earms more than what the calculators say.

Where are people mining? and are you have stability problems?

For the Nicehash haters, I want BTC and I don't want to convert to BTC daily and I want to take advance of the free Coinbase withdrawal. I'm not a fan of MPH because the reported hash rate is usually lower than the actual hash rate

hwajong

newbie

Activity: 1

Merit: 0

Quote from: yrk1957 on September 26, 2018, 10:22:20 AM

Starting this thread to share information about Zig Z1...

In case you don't know Zig Z1 is a new Lyra2Rev2 ASIC miner from Dayun. It hashes at 6.8GH/s, so that's about 100 1080Tis, with 1250w power consumption, so about 1/20th the power. Dayun seems to be a new manufacturer. They had a website - https://dayunminer.com, but that seems to have disapperaed now!.

I got mine from asicminermarket. It has its own unique UI, you can see screenshots on asicminermarket. I was on nicehash, getting about 6.5GH/s on average for 2 days. Four hash boards, and seems to run off a USB flash drive.

That was the good part. Now for the bad. Its startup is quite shaky. I needed to re-start the miner process many times for it start hashing. It worked fine for a couple of days, but now its stopped. It comes on, network lights flash, red light stay on, network lights stop flashing, and start flashing again. Looks like its re-booting continuously. If anyone has clues please share.

Thanks!

mattaero

jr. member

Activity: 178

Merit: 2

Quote from: zizou10 on October 04, 2018, 01:00:33 PM

Quote from: mattaero on October 04, 2018, 12:55:58 PM

that is strange.over the course of an hour or two are you earning what you would expect to earn on nicehash? (like $6.50 for 2 hours)

No, less than that. More like 4,5-5 for two hours.

I am a bit lower than what I would expect too but not that low. I would check the PSU (if you are at 120V one apw3 probably isn't enough) and make sure #xnsub is at the end of the pool address.

Other than that not sure what it could be. see if the number of shares accepted on the Z1 dashboard are roughly the same for each hash board. If not, then you know where the problem lies.

zizou10

newbie

Activity: 4

Merit: 0

Quote from: mattaero on October 04, 2018, 12:55:58 PM

that is strange.over the course of an hour or two are you earning what you would expect to earn on nicehash? (like $6.50 for 2 hours)

No, less than that. More like 4,5-5 for two hours.

mattaero

jr. member

Activity: 178

Merit: 2

that is strange.over the course of an hour or two are you earning what you would expect to earn on nicehash? (like $6.50 for 2 hours)

zizou10

newbie

Activity: 4

Merit: 0

Quote from: mattaero on October 04, 2018, 12:41:19 PM

Quote from: zizou10 on October 04, 2018, 12:19:39 PM

Hi guys,

I have purchased a Dayun Zig Z1 asic few day ago. After having set it up the hashrate on the asic is very unstable (keeps going up to 10GH and then coming down to 0 again all the time).

I have mounted the firmware on the disk again today and reduced the frequency to 800 mhs, but still no luck the hashrate keeps jumping up and down.

Does anyone have a similar problem or maybe a solution?

Thanks

\

What the miner shows you is useless. Start mining on a pool and check your average hash rate after an hour or two.

I see the same thing on the nicehash as well. The hashrate goes up then it goes back down to 0 again and the uptime as well goes to 0.

mattaero

jr. member

Activity: 178

Merit: 2

Quote from: zizou10 on October 04, 2018, 12:19:39 PM

Hi guys,

I have purchased a Dayun Zig Z1 asic few day ago. After having set it up the hashrate on the asic is very unstable (keeps going up to 10GH and then coming down to 0 again all the time).

I have mounted the firmware on the disk again today and reduced the frequency to 800 mhs, but still no luck the hashrate keeps jumping up and down.

Does anyone have a similar problem or maybe a solution?

Thanks

\

What the miner shows you is useless. Start mining on a pool and check your average hash rate after an hour or two.

zizou10

newbie

Activity: 4

Merit: 0

Hi guys,

I have purchased a Dayun Zig Z1 asic few day ago. After having set it up the hashrate on the asic is very unstable (keeps going up to 10GH and then coming down to 0 again all the time).

I have mounted the firmware on the disk again today and reduced the frequency to 800 mhs, but still no luck the hashrate keeps jumping up and down.

Does anyone have a similar problem or maybe a solution?

Thanks

Aurelchan

copper member

Activity: 11

Merit: 3

Quote from: deneme12 on October 03, 2018, 06:35:00 AM

Very interesting thing. Send a review message for dayun zig 1 on dayun.company. They change your message and publish on website. I wrote

1 board is not working. I sent mail to dayun company and no reply and gave 1 star. Published message is this

" Thanks! My miners came to me, you are the best! "

This shows the objectivity of the company. You can try like me.

I have one more question. I updated to last firmware but still one board is dead. Is there any way to wake it up ?

Could you give us the url of the company please ?

jadrew1020

newbie

Activity: 17

Merit: 2

Quote from: Crippt on September 29, 2018, 05:25:58 PM

Hi to all of you guys in this my first message on the forum and sorry for my bad English,

Well, I'm thinking about to buy the Zig Z1 but I'm very afraid of scams and I don't know this miner manofacturer and don't know anyone ho has one. Please, could you give me some information? anyone has bought one? in what store? Any problems with the miner, good or bad quality?

Thanks!!!

Hello Crippt,

I recently purchased a Dayun Zig Z1 from crypto drilling. I was also skeptical at first, I proceeded to the wire transfer and everything worked out. I live in canada quebec and the delivery only took 4 days. Also they have a very fast response when sending emails. I recommend them!

Jamie

Bitreo

newbie

Activity: 14

Merit: 0

Quote from: mattaero on October 03, 2018, 03:55:46 PM

I am having some decent hash rates with Nicehash, but I have between 3-5% stale shares...probably because it goes through a switch with 8 other miners on it, but in case its software related...Anyone know if I can add these commands from the nicehash page into the Dayun miner JSON?

"if you have access to software fine-tuning, you can experiment with these cgminers/BFGMiners additional settings: --queue 0 --scan-time 1 --expiry 1"

if you want to modify the config files on the filesystem then you need to get the root password. if anyone can crack the password here is the hash :

Username: root
PW Hash: $6$pvnavTv2$2W/s.veJLVbb1g9qJpFO7ATNNBiOtwt.MXABU6nRVgJwuiS3WlBrRMj0avAdnHL

Username: fa
PW Hash: $6$muvIxroU$Lcuu06mrLbEONRLK312njB.RTI4dbC9QdJAZ6Bam0RnJpibRO2K62XHBKRKRo3U1IDFTtTAdXb/h.vp8vXuio1

regards

justin1197

newbie

Activity: 3

Merit: 0

Quote from: mattaero on October 03, 2018, 08:28:08 AM

Quote from: justin1197 on October 03, 2018, 12:22:39 AM

Hi All,

Just received new Zig Z1. Machine not booting at all, powers up but red light is always on. It wont connect to the network so i cant set it up. Appreciate any help.

Cheers JB

Try and follow the video I posted a few posts back. I set the first pool address to an IP address, the second to nicehash, and changed the settings in the miner to static (I put mine at 192.168.1.100) and then go to your router settings and set the DHCP to static instead of dynamic for that IP address.

Try that, and wait like 5 minutes.

Hi,

Thankyou for your help. Can't find you post with the video. Could you please post link again.
Cheers
JB

mattaero

jr. member

Activity: 178

Merit: 2

I am having some decent hash rates with Nicehash, but I have between 3-5% stale shares...probably because it goes through a switch with 8 other miners on it, but in case its software related...Anyone know if I can add these commands from the nicehash page into the Dayun miner JSON?

"if you have access to software fine-tuning, you can experiment with these cgminers/BFGMiners additional settings: --queue 0 --scan-time 1 --expiry 1"

mattaero

jr. member

Activity: 178

Merit: 2

Quote from: ?? on ??

Quote from: mattaero on October 03, 2018, 02:21:30 PM

Since you actually can make significant changes to the Zig Z1 (because you have an external boot drive that could conceivably be programmed) wonder if it would be considered the same? Obviously it would be a pain in the ass, but I would assume a linux and html programmer could make all sorts of changes. (I am not one of those people, lol).

In any event, if I order another one I will make sure they value it at under $1,000 just in case! I want to get at least another week of steady profits before I consider spending that much money again.

Currently I am at work and it looks like one of the has boards is not functioning (getting 5.4 Mh/s) which is super annoying.

Anyone know how I set up remote access through a Verizon quantum router? lol

I'll sell you mine if you're interested.

Also, I just use TeamViewer and remote into my desktop at home from my phone / work computer / wherever I may be

I might be interested at some point, depending on the cost. However, given the amount of money involved, I am not sure how we would do it such that I would feel comfortable unless we did it through Ebay or something similar. Or if you happen to live near me, which seems unlikely.

Topic: Dayun Zig Z1 - Lyra2Rev2 6.8GH/s Asic miner - page 56. (Read 42511 times)