The gtx 960 can go from 11 to 14MHASH with small modifications to the code. I run with --farm-recheck 150
That low of a farm-recheck value will skew your hashrate output.
Topic: ethminer-0.9.41-genoil-1.1 - page 42. (Read 397363 times)
That low of a farm-recheck value will skew your hashrate output.
so how can i download it 
1.1.5 is out. Adds support for nicehash stratum (add -ES flag), as well as a third option to load DAGs. This is only supported on CUDA for the time being. It allows you to generate the DAG on 1 GPU and then distribute it via system RAM to the other GPUs. Usage: -L single , where is the GPU ID. As I don't have a dev system with multiple OpenCL GPU's on the same platform, I can't currently port this to OpenCL.
This work has all been done by nicehash themselves, thank you!
It kind of paves the way for supporting more stratum variants, so -ES wil probably change into -SM in an upcoming release.
This work has all been done by nicehash themselves, thank you!
It kind of paves the way for supporting more stratum variants, so -ES wil probably change into -SM
that would be awsome
lololol, only if computers have a REALLY GOOD videocards
That is very good performance. 670 is a very old card. Maybe their memory bandwidth is quite high to have such high speed.
Apparently it can do even better with slight OC.
https://bitcointalksearch.org/topic/m.15236264
Each PC is around 160w at the wall when mining. But my electric cost is included in rent... so I doesn't bother me....
I want to try with my GTX 950 OC 
.
what i write in the .bat ? The best mining pool ?
Thanks! .
.what i write in the .bat ? The best mining pool ?
Thanks! .
that would be awsome
lololol, only if computers have a REALLY GOOD videocardsThat is very good performance. 670 is a very old card. Maybe their memory bandwidth is quite high to have such high speed.
970 already has those 10% because of natively supported warp shuffle and better compiler.
Not entirely sure about that. I took some ghetto math shortcuts.
I know and I should try hacking those into PTX if possible at all. But with the current CUDA kernel I can simply run the first keccak stage twice and not lose any performance, so I don't think it will do a great deal.
Anyone using maxas here? https://github.com/NervanaSystems/maxas
No, no, I meant in the rest of the code.
> 13.7MHs
Not bad
better than 960
but what about power draw?
Not bad
better than 960
but what about power draw?
970 already has those 10% because of natively supported warp shuffle and better compiler.
Not entirely sure about that. I took some ghetto math shortcuts.
that would be awsome
lololol, only if computers have a REALLY GOOD videocards Is their a read me for all the -- commands and what they do been looking everywhere and cant seem to find anywhere that has all the old commands and all new commands and what each one does.
try thisCode:
ethminer -h
pause
I don't know where Claymore gets his additional 5-ish percent performance increase from, but I really can't keep up with the features he keeps adding to his miner. But mine is free
I don't think Claymore's miner is faster, I think he gets the increase because his stratum protocol works allowing a direct connection to Dwarf. Supposedly this makes a big difference going direct rather then over eth-proxy... If you got stratum working with dwarf I think you would be just as fast. Great miner. Thank you for your work. Good way to verify would be testing solo mode with each as solo mode must use HTTP.
Actually, while I can get
10% on amd only right? because if it is on the 970 too, that's what i call impressive
AMD only right now; as I don't have a 970 to test, even if my mods applied, I wouldn't be able to check them.
Is their a read me for all the -- commands and what they do been looking everywhere and cant seem to find anywhere that has all the old commands and all new commands and what each one does.
that would be awsome
lololol, only if computers have a REALLY GOOD videocards
Genoil...
could you make screen saver miner?
I have a lot of computers in my office that are often unused, so if I could have a screesaver that mines when computer is idle... that would be awsome
could you make screen saver miner?
I have a lot of computers in my office that are often unused, so if I could have a screesaver that mines when computer is idle... that would be awsome
I don't know where Claymore gets his additional 5-ish percent performance increase from, but I really can't keep up with the features he keeps adding to his miner. But mine is free
I don't think Claymore's miner is faster, I think he gets the increase because his stratum protocol works allowing a direct connection to Dwarf. Supposedly this makes a big difference going direct rather then over eth-proxy... If you got stratum working with dwarf I think you would be just as fast. Great miner. Thank you for your work. Good way to verify would be testing solo mode with each as solo mode must use HTTP.
Actually, while I can get
Hi I picked up my first 980ti to add into the farm. It sounded like a good idea at the time but does not seem to be performing as well as expected. (Compared to my others - 950/960/970) I'm only getting around 18MH/s and it sounds like I should be getting more. It's running on Mint 17.3 with ethminer 1.1.4, does anyone have any suggestions for the optimal command line options? If I can't get better then that I might as well return and get a 970. Thanks for any help.
You should be able to get 20+ by forcing the card into P0 state: http://cryptomining-blog.com/7341-how-to-squeeze-some-extra-performance-mining-ethereum-on-nvidia/
But it won't be much faster than a 970, so that's a better use of your money.
Thanks for the tip.
My miner isnt creating the DAG files, i´ve checked APPDATA and theres nothing there, how can i fix this? The normal ethminer creates the DAG files.
From version 1.1 and up there aren't any DAG files
Thanks for the fast response!
Great work.
Quote
1.1.3
i m a bit confuse what s the last version? is it not the 0.9.41?
0.9.41 was the version of ethminer when I forked it. 1.1.3 is the release number of the fork.
Is the stratum code working in the OpenCL build of 1.1.4?
It builds fine, and runs great using network - but, I'm getting a missing symbol when using a -S (stratum) config with Ubuntu 15.10.
Does it need a link to boost? or is that built-in?
Anyone else running stratum with 1.1.4?
If so, would you please share your config line.
thanks!
Does donkeypool support stratum now?
Late testing phase - DonkeyPool should be stratum-ready by Monday
My miner isnt creating the DAG files, i´ve checked APPDATA and theres nothing there, how can i fix this? The normal ethminer creates the DAG files.
From version 1.1 and up there aren't any DAG files
Jump to: