GekkoScience 2Pac/Compac BM1384 Stickminer Official Support Thread - page 49.

goose1072

full member

Activity: 235

Merit: 100

Quote from: marousi on January 04, 2018, 05:41:47 AM

cgminer 4.10.0 does not support --gekko freq but does support --compac-freq. Still how to turn that goddamm tiny screw?

I have been using c:\cgminer-4.10.0-windows-gekko\cgminer.exe -o stratum+tcp://what ever you mine at -u goose1072.gekko -p x --usb :2 --gekko-2pac-freq 150

and it works without any issues.

you need to create a bat file to use the above command.

der_wasi

member

Activity: 111

Merit: 10

Quote from: marousi on January 04, 2018, 05:41:47 AM

cgminer 4.10.0 does not support --gekko freq

Who told you so? --gekko-2pac-freq is the usual way to set the 2pac frequency.

Quote from: marousi on January 04, 2018, 05:41:47 AM

Still how to turn that goddamm tiny screw?

Maybe with a goddamn tiny screwdriver? Wink

Like I said before, turn it clockwise until there are no new HW errors appearing.

marousi

newbie

Activity: 123

Merit: 0

cgminer 4.10.0 does not support --gekko freq but does support --compac-freq. Still how to turn that goddamm tiny screw?

der_wasi

member

Activity: 111

Merit: 10

Quote from: goose1072 on January 03, 2018, 04:12:57 PM

so which would you recommend for overclocking to at least 225Mhz?

I have a 30 W hub without any limits per one port. With this I had two sticks running at 250 MHz. But this needed an absolutely correct voltage setting. So that would be a current of 3 A per stick. (30 W / 2 sticks / 5 V = 3 A)

Quote from: marousi on January 04, 2018, 04:52:18 AM

How to turn the screw to increase hashrate? What tool do I need?

That´s a little more complicated. To increase the hashrate you need to increase the frequency with the --gekko-2pac-freq command during start of cgminer. If you increase the frequency you need more voltage to avoid HW errors. So if you increase the frequency and there are no HW errors shown inside cgminer, it´s fine. If there are any HW errors you need to adjust the voltage by turning the pot slowly clockwise until the HW errors stop counting up.

marousi

newbie

Activity: 123

Merit: 0

How to turn the screw to increase hashrate? What tool do I need?

sunk818

full member

Activity: 1176

Merit: 111

Quote from: ParaplegicRacehorse on January 04, 2018, 02:49:37 AM

Quote from: ugie1028 on January 03, 2018, 05:10:44 PM

So cgminer does see it, its just not responding. Why?

Im sure this is a defective device now. If the other one works, then this should to, or at least get detected.

Couple question: Per the first post, are you running stock cgmining or the version with drivers for these? (-vh)

If you're running with -vh, did you compile with --enable-gekko?

Only other thing to try is tweaking voltage to see if it fits upon insert because port can't handle power . draw. If you have multimeter that helps to troubleshoot but you can blind turn the pot to adjust voltage
See page 1 on how to adjust voltage

ParaplegicRacehorse

member

Activity: 79

Merit: 36

HODL. Patience.

Quote from: ugie1028 on January 03, 2018, 05:10:44 PM

So cgminer does see it, its just not responding. Why?

Im sure this is a defective device now. If the other one works, then this should to, or at least get detected.

Couple question: Per the first post, are you running stock cgmining or the version with drivers for these? (-vh)

If you're running with -vh, did you compile with --enable-gekko?

ugie1028

newbie

Activity: 10

Merit: 0

I have an update on my asic miner. Gekkoscience 2pac bm1384usb bitcoin miner.

I decided to let it run with cgminer alone. Still doesnt detect it. I did enable verbose. And i get this little nugget.

Device serial GS-10017684 not responding.

So cgminer does see it, its just not responding. Why?

Im sure this is a defective device now. If the other one works, then this should to, or at least get detected.

goose1072

full member

Activity: 235

Merit: 100

so which would you recommend for overclocking to at least 225Mhz?

der_wasi

member

Activity: 111

Merit: 10

The Block Erupter has only 0.5 to 1 A per port. That´s not enough unless you don´t want to overclock. But for more than 100 MHz 1 A is too low.

goose1072

full member

Activity: 235

Merit: 100

I have been using these hubs with no issues but you can only have 3 miners on them and only use poet 2, 4 & 6.
https://www.amazon.com/gp/product/B00L2LK164/ref=oh_aui_detailpage_o06_s02?ie=UTF8&psc=1

I am about to purchase this hub since I have 10 miner now and don't have enough power to run them all:
https://www.amazon.com/gp/product/B00GCQQE42/ref=ox_sc_act_title_1?smid=A1TSKG9WMIX8W&psc=1

I have been reading good things about the Block Erupter will let you know how it works out.

DKirk

newbie

Activity: 61

Merit: 0

Quote from: 80sKid on January 03, 2018, 01:26:23 PM

Quote from: ITFlyGuy on January 03, 2018, 11:23:05 AM

I have an AnkerUSB 3.0 SuperSpeed 10-Port Hub - so far unable to get it working with the RSPI 3 - wondering if anyone has used this hub?

Thanks

Is the hub not working with the RSPI3, or do you mean a 2Pac miner in the hub doesn't work with the RSPI3?

Looks like the number 10 port on your hub allows the most power. Have you tried that one? Have you tried plugging one 2Pac directly into the RSPI3? If so, does that work?

I thought I remember reading somewhere on here that you don't want to use Anker hubs with a Pi/2pac setup... Might want to dig a bit on that.

80sKid

newbie

Activity: 7

Merit: 0

Quote from: ITFlyGuy on January 03, 2018, 11:23:05 AM

I have an AnkerUSB 3.0 SuperSpeed 10-Port Hub - so far unable to get it working with the RSPI 3 - wondering if anyone has used this hub?

Thanks

Is the hub not working with the RSPI3, or do you mean a 2Pac miner in the hub doesn't work with the RSPI3?

Looks like the number 10 port on your hub allows the most power. Have you tried that one? Have you tried plugging one 2Pac directly into the RSPI3? If so, does that work?

ugie1028

newbie

Activity: 10

Merit: 0

Thanks! Hope this fixes my problem. Ill come back here if it works (or doesnt.) Would help another lost user like myself.

ppetrovic68

full member

Activity: 140

Merit: 100

Quote from: ugie1028 on January 03, 2018, 12:55:01 PM

it doesn't make sense, sort of. why does one work (alone), and not the other?

looks like ill have to buy a USB hub. any recommendations? i can grab one today.

This one will work for two sticks (or three if you don't overclock a lot) https://plugable.com/products/usb2-hub7bc/

If you plan on overclocking, grab a multimeter as well, if you don't have one already.

There is also an usb hub thread https://bitcointalksearch.org/topic/now-that-usb-sticks-are-being-sold-by-sidehack-here-is-a-new-usb-hub-thread-1779423

wavelengthsf

full member

Activity: 658

Merit: 118

Quote from: ITFlyGuy on January 03, 2018, 11:23:05 AM

I have an AnkerUSB 3.0 SuperSpeed 10-Port Hub - so far unable to get it working with the RSPI 3 - wondering if anyone has used this hub?

Thanks

Lots of issues with a USB3 hub on the Pi, especially the anker. You can put a cheapo USB2 hub between the USB3 hub and the Pi and it should work.

ugie1028

newbie

Activity: 10

Merit: 0

it doesn't make sense, sort of. why does one work (alone), and not the other?

looks like ill have to buy a USB hub. any recommendations? i can grab one today.

der_wasi

member

Activity: 111

Merit: 10

You definitely need a hub. Usually they don´t work with the stock usb ports.
Buy a hub with enough power to supply both sticks. Maybe with a 30 W power supply. Better more.

ugie1028

newbie

Activity: 10

Merit: 0

Quote from: ugie1028 on January 03, 2018, 11:42:10 AM

Quote from: der_wasi on January 03, 2018, 10:55:53 AM

Did you try the defect one alone? What USB hub are you using? In what position is the potentiometer for the voltage adjustment? It´s located in the lower right edge with sight on the non heatsink side and USB port at the bottom. There is a flat edge on the pot. Try turning it to 3 o´clock.

thank you for the reply!

yes i tried the defect alone. nothing.

not using a hub. (yet) i have usb 3.0 ports. the fact that one works and one doesnt shouldnt be an issue with the power output. (I think, probably wrong.) yes ive also swapped them in the same port. the one that works, works on all the 3.0 ports. the defunct gets detected by zadig, and control panel, but doesn't get picked up by cgminer alone or together.

i will try turning the screw. I had an idea to mess with it. but i dont know what im doing. im a noob. im learning. im hoping to setup a large rig in the future. this is all a learning experience for me at the moment.

I just tried to turn it to 3'0clock. nothing. i even positioned it like the other working one. the light on it is just green. (always like that.) the working one pulsates blue and green. its been working since it came out of the box. this one is like brain dead. lights are on, but no ones home.

ugie1028

newbie

Activity: 10

Merit: 0

Quote from: der_wasi on January 03, 2018, 10:55:53 AM

Did you try the defect one alone? What USB hub are you using? In what position is the potentiometer for the voltage adjustment? It´s located in the lower right edge with sight on the non heatsink side and USB port at the bottom. There is a flat edge on the pot. Try turning it to 3 o´clock.

thank you for the reply!

yes i tried the defect alone. nothing.

not using a hub. (yet) i have usb 3.0 ports. the fact that one works and one doesnt shouldnt be an issue with the power output. (I think, probably wrong.) yes ive also swapped them in the same port. the one that works, works on all the 3.0 ports. the defunct gets detected by zadig, and control panel, but doesn't get picked up by cgminer alone or together.

i will try turning the screw. I had an idea to mess with it. but i dont know what im doing. im a noob. im learning. im hoping to setup a large rig in the future. this is all a learning experience for me at the moment.

Topic: GekkoScience 2Pac/Compac BM1384 Stickminer Official Support Thread - page 49. (Read 177467 times)