[GUIDE][TUTORIAL][XMR,ETH]How To Mod Bios RX470/570/480/580 VEGA Mining 💰⛏ - page 36.

Bitock

full member

Activity: 213

Merit: 100

Quote from: ?? on ??

Quote from: Bitock on November 08, 2017, 01:43:24 AM

Quote from: greatauror28 on November 07, 2017, 11:10:33 PM

Quote from: Bitock on November 07, 2017, 04:55:05 PM

I have msi rx580 8gb with hynix memory. I took timings from here http://indeedminers.czechian.net/timings.html and wrote its to 2:1750, 2:2000, 2:2250. First I tried the first timing, after second. When I run miner my system crashed. What am I doing wrong?

I’m sure his Asic quality is higher than your cards hence the crash.

I suggest doing your own trial-and-error until you find your card’s sweet spot.

How can I get about 30mh/s from my card? I get ~27,7mh/s from original bios and writed timings from 2:1750 to 2:2000, 2:2250 without memory errors.
I read a lot of forums and find topics where suggest mod_bios for my card but only with a lot of memory errors.
Help, please!

I cleared 31MH/s stable, and 32MH/s was unstable at the time... but since I only have like one or two cards with that memory, I said fuck it; it's not worth my time to improve it to 32MH/s+, as it can be a *really* picky bitch.

Cool.
Are you write strap 2:2000, 2:2250 or other yet?
Timings take from 2:1750?

Bitock

full member

Activity: 213

Merit: 100

Quote from: greatauror28 on November 07, 2017, 11:10:33 PM

Quote from: Bitock on November 07, 2017, 04:55:05 PM

I have msi rx580 8gb with hynix memory. I took timings from here http://indeedminers.czechian.net/timings.html and wrote its to 2:1750, 2:2000, 2:2250. First I tried the first timing, after second. When I run miner my system crashed. What am I doing wrong?

I’m sure his Asic quality is higher than your cards hence the crash.

I suggest doing your own trial-and-error until you find your card’s sweet spot.

How can I get about 30mh/s from my card? I get ~27,7mh/s from original bios and writed timings from 2:1750 to 2:2000, 2:2250 without memory errors.
I read a lot of forums and find topics where suggest mod_bios for my card but only with a lot of memory errors.
Help, please!

phuocduong

member

Activity: 182

Merit: 10

helpful for miner, i used his 470 4g (hynix), after mod mining ETH about 27 Mhz (claymore)

greatauror28

full member

Activity: 181

Merit: 101

Ethereum Miner

Quote from: Bitock on November 07, 2017, 04:55:05 PM

I have msi rx580 8gb with hynix memory. I took timings from here http://indeedminers.czechian.net/timings.html and wrote its to 2:1750, 2:2000, 2:2250. First I tried the first timing, after second. When I run miner my system crashed. What am I doing wrong?

I’m sure his Asic quality is higher than your cards hence the crash.

I suggest doing your own trial-and-error until you find your card’s sweet spot.

Bitock

full member

Activity: 213

Merit: 100

I have msi rx580 8gb with hynix memory. I took timings from here http://indeedminers.czechian.net/timings.html and wrote its to 2:1750, 2:2000, 2:2250. First I tried the first timing, after second. When I run miner my system crashed. What am I doing wrong?

clems

member

Activity: 171

Merit: 10

Quote from: ?? on ??

Hi, I made the mod, but the power consumption increased. Could you help ?

Doesn't matter for me ^^ but it can be good to know.

clems

member

Activity: 171

Merit: 10

That's a good point and thanks Roll Eyes

You could say: RTFM

ETH - Total Speed: ETH: GPU0 30.929 Mh/s

Thanks.

Branko

sr. member

Activity: 2674

Merit: 328

Quote from: clems on November 05, 2017, 05:34:27 AM

Someone have the same increasing Hashrate when dual mining?

Only the people that don't know that dcri parameter works in single mining mode too

clems

member

Activity: 171

Merit: 10

Hello,

Thanks so much man for this Tutorial !!!!!!!!!

My rig base on AMD NITRO+ RX 580 8G Hynix + Ubuntu 16.04 Server with AMD beta blockchain drivers + Claymore:

Each GPU for "Estash"
30.7 Mh/s
Temp=62C
Fan=36%
120W ( 0.017$ KWh so I don't really work on that ^^)

On Windows the Hash is better 31.4Mh/s but Linux is more stable and...I don't want to work on Windows anyway.

Strange thing is when I start Dual-Mining my hashrate increase to 30.9 Mh/s and 970 for DRE but I will not use Dual mining !! Dual Mining is taking 60W more / Lot more noisy and Fan start to go high...

Someone have the same increasing Hashrate when dual mining?

tarui

sr. member

Activity: 294

Merit: 250

is there any differences between the various brands of vega 56/64 in terms of quality?

greatauror28

full member

Activity: 181

Merit: 101

Ethereum Miner

Quote from: wazooland on October 31, 2017, 01:01:23 AM

Quote from: greatauror28 on October 30, 2017, 02:52:35 PM

Quote from: wazooland on October 30, 2017, 11:15:41 AM

Quote from: greatauror28 on October 30, 2017, 12:17:21 AM

Quote from: Gunna01 on October 29, 2017, 08:40:27 PM

Whats the best way to undervolt my cards?

I have 2 x MSI ARMOR 4GB RX570 and 4 x Aorus 4GB RX570 split across 2 PSU. From the wall i'm pulling 1010kw so very keen to drop this as low as possible. Getting 161mh/s from this rig and at up 24Kw a day @ .30c per KW for power it's expensive, even with solar.

If you use Claymore miner, it's easy to set -mvddc and -cvddc.

I have 6-card rig as well and pull ~1040w at the wall, but these are 580s dual-mining 177eth 4.2Gh dcr.

I thought 570s are supposed to pull only around 90w eth-only mining?

Thanks you. I have just removed AB and add some commands into claymore config.
Now, my rig is working good, but memory error is still there (a bit).

Welcome!

Try stepping down a notch on your memory clock, say from 2100 go down to 2075 until it's showing less than 10 errors per minute. The target however is to have zero for maximum rig stability.

Thank for your reply.
Today, I have reduced CC: 1150, MC: 2000, mvddc: 930, cvddc:920, PL: 25. But memory errors have still appeared with minimum (2 errors/ minute).
I will continue.....

I'd be okay with 2 errors per minute, as memory errors doesn't necessarily mean a bad thing. Some mem errors means the card is correcting some stuff.

What you should watch out are thousand errors per minute. Voltage plays a lot of factor too.

wazooland

newbie

Activity: 34

Merit: 0

Quote from: greatauror28 on October 30, 2017, 02:52:35 PM

Quote from: wazooland on October 30, 2017, 11:15:41 AM

Quote from: greatauror28 on October 30, 2017, 12:17:21 AM

Quote from: Gunna01 on October 29, 2017, 08:40:27 PM

Whats the best way to undervolt my cards?

I have 2 x MSI ARMOR 4GB RX570 and 4 x Aorus 4GB RX570 split across 2 PSU. From the wall i'm pulling 1010kw so very keen to drop this as low as possible. Getting 161mh/s from this rig and at up 24Kw a day @ .30c per KW for power it's expensive, even with solar.

If you use Claymore miner, it's easy to set -mvddc and -cvddc.

I have 6-card rig as well and pull ~1040w at the wall, but these are 580s dual-mining 177eth 4.2Gh dcr.

I thought 570s are supposed to pull only around 90w eth-only mining?

Thanks you. I have just removed AB and add some commands into claymore config.
Now, my rig is working good, but memory error is still there (a bit).

Welcome!

Try stepping down a notch on your memory clock, say from 2100 go down to 2075 until it's showing less than 10 errors per minute. The target however is to have zero for maximum rig stability.

Thank for your reply.
Today, I have reduced CC: 1150, MC: 2000, mvddc: 930, cvddc:920, PL: 25. But memory errors have still appeared with minimum (2 errors/ minute).
I will continue.....

Gunna01

sr. member

Activity: 306

Merit: 251

Quote from: greatauror28 on October 30, 2017, 12:17:21 AM

Quote from: Gunna01 on October 29, 2017, 08:40:27 PM

Whats the best way to undervolt my cards?

I have 2 x MSI ARMOR 4GB RX570 and 4 x Aorus 4GB RX570 split across 2 PSU. From the wall i'm pulling 1010kw so very keen to drop this as low as possible. Getting 161mh/s from this rig and at up 24Kw a day @ .30c per KW for power it's expensive, even with solar.

If you use Claymore miner, it's easy to set -mvddc and -cvddc.

I have 6-card rig as well and pull ~1040w at the wall, but these are 580s dual-mining 177eth 4.2Gh dcr.

I thought 570s are supposed to pull only around 90w eth-only mining?

What mvddc and cvddc are you using?

Mattthev

sr. member

Activity: 966

Merit: 359

👉MINING-BIOS.eu💲⛏

Updated tools and drivers

greatauror28

full member

Activity: 181

Merit: 101

Ethereum Miner

Quote from: wazooland on October 30, 2017, 11:15:41 AM

Quote from: greatauror28 on October 30, 2017, 12:17:21 AM

Quote from: Gunna01 on October 29, 2017, 08:40:27 PM

Whats the best way to undervolt my cards?

I have 2 x MSI ARMOR 4GB RX570 and 4 x Aorus 4GB RX570 split across 2 PSU. From the wall i'm pulling 1010kw so very keen to drop this as low as possible. Getting 161mh/s from this rig and at up 24Kw a day @ .30c per KW for power it's expensive, even with solar.

If you use Claymore miner, it's easy to set -mvddc and -cvddc.

I have 6-card rig as well and pull ~1040w at the wall, but these are 580s dual-mining 177eth 4.2Gh dcr.

I thought 570s are supposed to pull only around 90w eth-only mining?

Thanks you. I have just removed AB and add some commands into claymore config.
Now, my rig is working good, but memory error is still there (a bit).

Welcome!

Try stepping down a notch on your memory clock, say from 2100 go down to 2075 until it's showing less than 10 errors per minute. The target however is to have zero for maximum rig stability.

preda

sr. member

Activity: 756

Merit: 250

good tutorial!

wazooland

newbie

Activity: 34

Merit: 0

Quote from: greatauror28 on October 30, 2017, 12:17:21 AM

Quote from: Gunna01 on October 29, 2017, 08:40:27 PM

Whats the best way to undervolt my cards?

I have 2 x MSI ARMOR 4GB RX570 and 4 x Aorus 4GB RX570 split across 2 PSU. From the wall i'm pulling 1010kw so very keen to drop this as low as possible. Getting 161mh/s from this rig and at up 24Kw a day @ .30c per KW for power it's expensive, even with solar.

If you use Claymore miner, it's easy to set -mvddc and -cvddc.

I have 6-card rig as well and pull ~1040w at the wall, but these are 580s dual-mining 177eth 4.2Gh dcr.

I thought 570s are supposed to pull only around 90w eth-only mining?

Thanks you. I have just removed AB and add some commands into claymore config.
Now, my rig is working good, but memory error is still there (a bit).

botibot101

newbie

Activity: 11

Merit: 0

thanks for this tutorial and new tools

greatauror28

full member

Activity: 181

Merit: 101

Ethereum Miner

Quote from: Gunna01 on October 29, 2017, 08:40:27 PM

Whats the best way to undervolt my cards?

I have 2 x MSI ARMOR 4GB RX570 and 4 x Aorus 4GB RX570 split across 2 PSU. From the wall i'm pulling 1010kw so very keen to drop this as low as possible. Getting 161mh/s from this rig and at up 24Kw a day @ .30c per KW for power it's expensive, even with solar.

If you use Claymore miner, it's easy to set -mvddc and -cvddc.

I have 6-card rig as well and pull ~1040w at the wall, but these are 580s dual-mining 177eth 4.2Gh dcr.

I thought 570s are supposed to pull only around 90w eth-only mining?

Gunna01

sr. member

Activity: 306

Merit: 251

Whats the best way to undervolt my cards?

I have 2 x MSI ARMOR 4GB RX570 and 4 x Aorus 4GB RX570 split across 2 PSU. From the wall i'm pulling 1010kw so very keen to drop this as low as possible. Getting 161mh/s from this rig and at up 24Kw a day @ .30c per KW for power it's expensive, even with solar.

Topic: [GUIDE][TUTORIAL][XMR,ETH]How To Mod Bios RX470/570/480/580 VEGA Mining 💰⛏ - page 36. (Read 221013 times)