Topic: How to upgrade TPLINK TL-MR3020 firmware to technobit openwrt - page 10. (Read 57314 times)
Router restarted, command typed, but I'm not getting any hashing.
Thank you!
I may have missed this, but how do you update the tplink after switching to the technobit OpenWRT?
Go to SYSTEM - BACKUP / FLASH FIRMWARE
Choose keep setting so your various setting like IP & cgminer will be keep.
Then hit Flash image.., then Proceed
Do not closed your browser until router restart !!!
When all process done, ssh to the router & run command:
Code:
/usr/bin/fix_rc
PS: OP updated
I may have missed this, but how do you update the tplink after switching to the technobit OpenWRT?
using chrome 
Thx for the help
Was already expecting problems like this, so i've got two routers.
one for actual using and a spare 1 for upgrade.
This buys me time to upgrade
CoolThx for the help
Was already expecting problems like this, so i've got two routers.
one for actual using and a spare 1 for upgrade.
This buys me time to upgrade
using chrome
Thx for the help
Was already expecting problems like this, so i've got two routers.
one for actual using and a spare 1 for upgrade.
This buys me time to upgrade
Thx for the help
Was already expecting problems like this, so i've got two routers.
one for actual using and a spare 1 for upgrade.
This buys me time to upgrade
well i used your link. Download looks like previous one and same result 
Did an factory upgrade without keeping settings.
Same with the upgrade file. Even extra reboot does not solve it
Really dont know why i dont get the a3 option
Hostname HEX16A
Model TP-Link TL-MR3020 v1
Firmware Version OpenWrt Barrier Breaker r40296 / LuCI Trunk (svn-r9963)
Kernel Version 3.10.34
Finally solved it.
Went back to old image v 0.1.3 and then back again to this one. now i got the a3 option
First time i did the update was with upgrade bin file. now i did use only the factory bin files.
Is your ie cashing too much and same result Did an factory upgrade without keeping settings.
Same with the upgrade file. Even extra reboot does not solve it
Really dont know why i dont get the a3 option
Hostname HEX16A
Model TP-Link TL-MR3020 v1
Firmware Version OpenWrt Barrier Breaker r40296 / LuCI Trunk (svn-r9963)
Kernel Version 3.10.34
Finally solved it.
Went back to old image v 0.1.3 and then back again to this one. now i got the a3 option
First time i did the update was with upgrade bin file. now i did use only the factory bin files.
Usually the upgrade happens from the first try or shit happens and router became a brick
But in your case it was the browser
well i used your link. Download looks like previous one and same result
Did an factory upgrade without keeping settings.
Same with the upgrade file. Even extra reboot does not solve it
Really dont know why i dont get the a3 option
Hostname HEX16A
Model TP-Link TL-MR3020 v1
Firmware Version OpenWrt Barrier Breaker r40296 / LuCI Trunk (svn-r9963)
Kernel Version 3.10.34
Finally solved it.
Went back to old image v 0.1.3 and then back again to this one. now i got the a3 option
First time i did the update was with upgrade bin file. now i did use only the factory bin files.
and same result Did an factory upgrade without keeping settings.
Same with the upgrade file. Even extra reboot does not solve it
Really dont know why i dont get the a3 option
Hostname HEX16A
Model TP-Link TL-MR3020 v1
Firmware Version OpenWrt Barrier Breaker r40296 / LuCI Trunk (svn-r9963)
Kernel Version 3.10.34
Finally solved it.
Went back to old image v 0.1.3 and then back again to this one. now i got the a3 option
First time i did the update was with upgrade bin file. now i did use only the factory bin files.
ok, then something did go wrong. Cause what ever i try. The HexA3 option is not there.
Then you must be flash using wrong image. Here is the link: http://technobit.eu/0_3_2.rar
ok, then something did go wrong. Cause what ever i try. The HexA3 option is not there.
ok, clear answer.
But i see now i was not very clear with my question.
The dump of log came from router not being connected with a miner, so my question was about the cgminer version only
Sorry about me being not very clear.
Do not worry But i see now i was not very clear with my question.
The dump of log came from router not being connected with a miner, so my question was about the cgminer version only
Sorry about me being not very clear.
it is just a stupid txt file located in file system
/etc/hexminer_version or something
techno bit guy's probably forgot to update it also during build
just look what screen tells you dude. That is always correct
if there were HEX3 options inside the web you are golden...
ok, clear answer.
But i see now i was not very clear with my question.
The dump of log came from router not being connected with a miner, so my question was about the cgminer version only
Sorry about me being not very clear.
Ok, i did an upgrade: same version of cgminer
did an full upgrade (factory version of .bin file), same result.
Both without keeping the settings.
Wondering why i dont get cgminer version 4.2.3
But i see now i was not very clear with my question.
The dump of log came from router not being connected with a miner, so my question was about the cgminer version only
Sorry about me being not very clear.
Ok, i did an upgrade: same version of cgminer
did an full upgrade (factory version of .bin file), same result.
Both without keeping the settings.
Quote
Hex3A3 Chip Count
Cant find these settings, only HEX8A1 i can find and of course A,B and C versionWondering why i dont get cgminer version 4.2.3
just upgraded the router to 0.3.2 as you showed it is newest version.
But after upgrade i see this
[Firmware Version] => 20140329
cgminer: 4_1_0_5ed45a0
Socket connect failed: Connection refused
What happend? Should i upgrade again? not with upgrade file but with factory file?
mm, they are not absolete for me, managing to buy used ones for 30 euros or less, so i am starting to stack them now
But after upgrade i see this
[Firmware Version] => 20140329
cgminer: 4_1_0_5ed45a0
Socket connect failed: Connection refused
What happend? Should i upgrade again? not with upgrade file but with factory file?
mm, they are not absolete for me, managing to buy used ones for 30 euros or less, so i am starting to stack them now
You need to fill in Hex3A3 Chip Count (Default: 16), Hex3A3 Chip Frequency (Default: 7000), Hex3A3 Chip Core Voltage mV (Default: 750), Hex3A3 Enable or Disable Chips (Default: 255) with their default value which is blank right now
defaults are inside image. However if you do upgrade wile keeping settings do as zich suggested.
In general after each upgrade while keeping stings check the cgminer web and make sure there are no blanks there for all HEX* stuff
just upgraded the router to 0.3.2 as you showed it is newest version.
But after upgrade i see this
[Firmware Version] => 20140329
cgminer: 4_1_0_5ed45a0
Socket connect failed: Connection refused
What happend? Should i upgrade again? not with upgrade file but with factory file?
mm, they are not absolete for me, managing to buy used ones for 30 euros or less, so i am starting to stack them now
But after upgrade i see this
[Firmware Version] => 20140329
cgminer: 4_1_0_5ed45a0
Socket connect failed: Connection refused
What happend? Should i upgrade again? not with upgrade file but with factory file?
mm, they are not absolete for me, managing to buy used ones for 30 euros or less, so i am starting to stack them now
You need to fill in Hex3A3 Chip Count (Default: 16), Hex3A3 Chip Frequency (Default: 7000), Hex3A3 Chip Core Voltage mV (Default: 750), Hex3A3 Enable or Disable Chips (Default: 255) with their default value which is blank right now
just upgraded the router to 0.3.2 as you showed it is newest version.
But after upgrade i see this
[Firmware Version] => 20140329
cgminer: 4_1_0_5ed45a0
Socket connect failed: Connection refused
What happend? Should i upgrade again? not with upgrade file but with factory file?
mm, they are not absolete for me, managing to buy used ones for 30 euros or less, so i am starting to stack them now
But after upgrade i see this
[Firmware Version] => 20140329
cgminer: 4_1_0_5ed45a0
Socket connect failed: Connection refused
What happend? Should i upgrade again? not with upgrade file but with factory file?
mm, they are not absolete for me, managing to buy used ones for 30 euros or less, so i am starting to stack them now
mm, i'll see what wil happen.
hope it wil not die
hope it wil not die
Yeah, maybe you will be more lucky
Anyway my HEX16C going to retired in next difficulty change.
I will strip the heatsink & FAN then attach to HEX8A
mm, i'll see what wil happen.
hope it wil not die
Looks like u are right
hope it wil not die
Quote
[Chip12 Nonces] => 5070
[Chip12 Dupes] => 326
[Chip13 Nonces] => 21445
[Chip13 Dupes] => 75
[Chip12 Dupes] => 326
[Chip13 Nonces] => 21445
[Chip13 Dupes] => 75
Looks like u are right
lol, ok.
I did an upgrade to 4.2.2. yesterday, i'll do another one
Thx for info
Another question: having also a HEXc, it does run at 20 GHs when using 1500/1100 mv, but when using 1600/1160 it does run aprox 23.3 GHs, is this normal behaviour?
with 1500/1100 3 chips are not really doing fine (staying behind, can see this in tplink router log), but when using 1600/1160 they hardly stay behind.
I did an upgrade to 4.2.2. yesterday, i'll do another one
Thx for info
Quote
* cgminer bug fixes:HEXa frequent HEXa usb disconnects, fast work queue restart and so on
Having frequent hexa disconnects indeed, was already wondering why Another question: having also a HEXc, it does run at 20 GHs when using 1500/1100 mv, but when using 1600/1160 it does run aprox 23.3 GHs, is this normal behaviour?
with 1500/1100 3 chips are not really doing fine (staying behind, can see this in tplink router log), but when using 1600/1160 they hardly stay behind.
I guess chip number 3 is dead. If you run 1600/1160 for more long period, i bet that chip 3 will stop working.
I am also had 1 dead chip. I already try many higher setting but that's only work for short period.
lol, ok.
I did an upgrade to 4.2.2. yesterday, i'll do another one
Thx for info
Another question: having also a HEXc, it does run at 20 GHs when using 1500/1100 mv, but when using 1600/1160 it does run aprox 23.3 GHs, is this normal behaviour?
with 1500/1100 3 chips are not really doing fine (staying behind, can see this in tplink router log), but when using 1600/1160 they hardly stay behind.
I did an upgrade to 4.2.2. yesterday, i'll do another one
Thx for info
Quote
* cgminer bug fixes:HEXa frequent HEXa usb disconnects, fast work queue restart and so on
Having frequent hexa disconnects indeed, was already wondering why Another question: having also a HEXc, it does run at 20 GHs when using 1500/1100 mv, but when using 1600/1160 it does run aprox 23.3 GHs, is this normal behaviour?
with 1500/1100 3 chips are not really doing fine (staying behind, can see this in tplink router log), but when using 1600/1160 they hardly stay behind.
@Zich
Do u know how to see all the info when switching off the "toggle status switching"? (cgminer 4.2.2 tplink router 3020)
I would like to see all info all the time when using putty, not this switching
Do u know how to see all the info when switching off the "toggle status switching"? (cgminer 4.2.2 tplink router 3020)
I would like to see all info all the time when using putty, not this switching
That not available with cgminer-4.2.2. However, marto just release new image with cgminer-4.2.3 which possible to display all on one line.
0.3.2 Avalon 3 release technobit.eu/0_3_2.rar
0.3.2 HEX3A3 - Avalon3 board release
* HEX3A3 defaults: --hexminer3-chip-mask 255 --hexminer3-voltage 800 --hexminer3-options 16:7000
* HEX3A3 --hexminer3-options 16:7000 16 is chip count per board and 7000 is desired speed per chip in Mh/s. 7000 equals to 7G per chip.
* cgminer patch to cgminer 4.2.3 rev e574114682fe1edc344b7e291eb9d9497d26ef92.patch
* cgminer bug fixes:HEXa frequent HEXa usb disconnects, fast work queue restart and so on
* openwrt – some compile optimizations for speed which increased image size a bit
* openwrt – dhcp client added finally:)
* openwrt updated to r40449
0.3.2 HEX3A3 - Avalon3 board release
* HEX3A3 defaults: --hexminer3-chip-mask 255 --hexminer3-voltage 800 --hexminer3-options 16:7000
* HEX3A3 --hexminer3-options 16:7000 16 is chip count per board and 7000 is desired speed per chip in Mh/s. 7000 equals to 7G per chip.
* cgminer patch to cgminer 4.2.3 rev e574114682fe1edc344b7e291eb9d9497d26ef92.patch
* cgminer bug fixes:HEXa frequent HEXa usb disconnects, fast work queue restart and so on
* openwrt – some compile optimizations for speed which increased image size a bit
* openwrt – dhcp client added finally:)
* openwrt updated to r40449
Jump to: