Topic: How to upgrade TPLINK TL-MR3020 firmware to technobit openwrt - page 7. (Read 57314 times)

http://technobit.eu/0_3_8.rar

* 0.3.8
* cgminer for hex BTC Miners - patch to cgminer 4.5.0 rev_07c57008cfae8e210248394c90645bb920895b7f.patch
* cgminer for hex Scrypt Miners - patch to cgminer 4.5.0 srev_07c57008cfae8e210248394c90645bb920895b7f.patch
* cgminer - Please configure pool worker difficulty for best results and less rejects. Work pool updates and pool diff changes are handled properly. The pool paid shares should be increased with 1-2% hopefully. This hack is not tested with pool load balance mode. In case you mine in load balance mode make sure to setup pool worker difficulty.
* scgminer - Pending sync with cgminer rejects optimizations
* openwrt updated to r41917
 

New TP-link image and cgminer patch

http://technobit.eu/0_3_6.rar

* 0.3.6
* cgminer for hex BTC Miners - patch to cgminer 4.4.2 rev_45dbbb4cac091e41b0123fd211b6293436921681.patch
* cgminer for hex Scrypt Miners - patch to cgminer 4.4.2 srev_45dbbb4cac091e41b0123fd211b6293436921681.patch
* (s)cgminer A lot of dead/debug code has been removed and some optimizations were made. This image is not tested with HEXA and HEXC (Avalon 1 and Avalon 2) boards. Please be ready to downgrade if something is not working with HEXA and HEXC!
* openwrt updated to r41679
* BE200 (HEXE) options
* --hexminerbe200-options - asic_count:freq - default 16:300
* --hexminerbe200-asic-diff (default 0) - Allowed values are: 0 - diff 1, 1 diff 64, 2 diff 4096 and 3 diff 262144. Use 0 or 1 only. When using 1 make sure --hexminerbe200-nonce-timeout-secs is at least 120 secs! And your pool worker is configured properly, otherwise you are loosing hashes!
* --hexminerbe200-skip-hw-res (default 1) - Do not reset chips log only instead. Before enabling it make sure you your config is ok and it is not too aggressive
* --hexminerbe200-pic-roll (default 60 or 90) - BE200 PIC work internal roll count - Reduces dramatically USB load - range 0-255. Please use at least 10 or 20 here
* --hexminerbe200-hw-err-res (default 10) - reset chip due to N consecutive HW errors.
* --hexminerbe200-nonce-timeout-secs (default 5) - reset chip due to 0 nonces returned nonces returned for last N seconds.
* --hexminerbe200-chip-mask (default ffff Enable all chips) - Hex value to enable or disable chips
* --hexminerbe200-voltage (Default: 860)

Will the tp-link run any other hardware I have a rockminer and some u1's connected to the pc.

Tplink is 5wats what about your PC 200-300W?

I'm getting just one of the minion boards at the moment but will get more, I never considered going down pi route when I have a pc on 24/7 why get another device.

Thank you Zich! The one thing I was not getting is the boards do not need an ethernet connection. Thats what was throwing me off. Basically I only need 5 extra ports on my existing switch which is a 48 port so I don't need any switchs at all. Correct?

So how do we get the tp-link to run of the same power supply as the miner.

What psu are yo going to use?
As I said you need 1000w for each two boards or so..

 Ok, let's see if I am getting it now...

So i have 50 boards, split that into 10 segments. So with that said I have 10 boards, those 10 boards will all connect to a PSU for power. Then the 10 will go to a 10 port USB Hub connected to a TP-Link. The tplink and all boards can then be hooked up by ethernet to a large switch. Basically all 50 boards, and all tplinks go directly to a switch. Is this correct? Perhaps if Marto or someone else posted a definitive guide. I have a ton of stuff to order.

Wrong you need 5 separate switches or USB hubs for each tplink. However you can use one LAN switch to connect Ethernet cables

Ok, so to confirm.. I can run the 5 tp-links all off the same switch. I do not need a separate switch for each 10 boards correct?

Does this image work with the TL-703N or those old wiibox controllers from Gridseed?