HELP! Did something dumb.
Logged into TP-Link MR3020 via web page and set Network to from static to DHCP and now I cannot see it on any IP address.
DHCP server is enabled on the Internet router but it don't show up on the network.
I pressed the flashing reset button on boot-up but it didn't seem to reset OpenWRT to 192.168.1.1
Any ideas? Thanks.
Topic: How to upgrade TPLINK TL-MR3020 firmware to technobit openwrt - page 6. (Read 57389 times)
I'm happy I had 240ghs in x1's after the conversion i'm getting 430ghs so may make some roi after all the delays 
no back up pool pool says 446 and my avg is 430
That is good then 
First time I misunderstood you
It is just a luck that pool is above cgminer stats sometimes it may be opposite but avarage will always match to cgminer stats
no back up pool pool says 446 and my avg is 430
have a reject rate of 0.33% I think that's not too bad but I may be wrong.
Reject is fine but your pool stats shall match exactly to cgminer avarage speed minus rejectsDo you have backup pool?
Can you check if this pool is accepting shares also?
have a reject rate of 0.33% I think that's not too bad but I may be wrong.
I'm seeing around 450ghs on the cgminer and 430ish on the pool so I'm happy
Good the difference should be not so big. What is your reject rate?
And cgminer avarge spread. Do you have some shares leaking to your backup pool if you are using any?
I'm seeing around 450ghs on the cgminer and 430ish on the pool so I'm happy
I've set my nonce timeout to 5sec on my hex4m and it's running sound. It was 2sec default and it just kept resetting the damn chips.
Super duper 2 secs is at the edge for 400gh so if you are down clocking you should increase it also How is your pool graph by the way does it match with cgminer speed stats
I guess yes correct
I've set my nonce timeout to 5sec on my hex4m and it's running sound. It was 2sec default and it just kept resetting the damn chips.
Zich,
This difficulty which i can use in the settings of several miners, what is it exactly for?
i understand the difficulty of a mining pool, but when i look at it, this looks like its an another kind of diffuculty.
am i right here?
This difficulty which i can use in the settings of several miners, what is it exactly for?
i understand the difficulty of a mining pool, but when i look at it, this looks like its an another kind of diffuculty.
am i right here?
I guess the asic had the capability to filter the accepted nonce before send it to pool. This is similar to A1 asic.
This feature will reduce amount of data sent to pool.
But wrong setting on nonce timeout will make cgminer reset the asic. You will loose hash if it's reset every times 0 nonces return.
So you need to see how long the nonce return to pool each time.
Ok I give up this makes no sense today maybe tomorrow
i now see my error I need another usb hub, was using the one I have which is allready connected to my pc lol
i now see my error I need another usb hub, was using the one I have which is allready connected to my pc lol
Ok I give up this makes no sense today maybe tomorrow
i now see my error I need another usb hub, was using the one I have which is allready connected to my pc lol
i now see my error I need another usb hub, was using the one I have which is allready connected to my pc lol
but in the image a page back it shows the following.
router
switch
tp-link
hub
miner
so how lol
router
switch
tp-link
hub
miner
so how lol
just saw the image...pretty self explanatory but I will help ya out...
Plug your MINER (or USB hub) into the TP-Link unit USB port (standard A-not mini)
Plug the TP-Link unit into your switch (if no switch, straight into router) via LAN
Plug a MINI USB into the TP-Link unit for power
but in the image a page back it shows the following.
router
switch
tp-link
hub
miner
so how lol
router
switch
tp-link
hub
miner
so how lol
I thought that just need some info on what port connects where, anyone have this please.
I'd imagine that the miner will plug into the standard USB ports and ethernet into the LAN, power into the mini USB.
Not many other choices really from what I can tell.
I thought that just need some info on what port connects where, anyone have this please.
Ok I need putting straight on some things.
1, the miner has a mirco usb port that connects to the hub.
2, the tp-link has 2 usb ports and a lan port, 1 micro usb and one male usb. the micro is for power how do I connect the tp-link to the hub do I use the micro usb.
1, the miner has a mirco usb port that connects to the hub.
2, the tp-link has 2 usb ports and a lan port, 1 micro usb and one male usb. the micro is for power how do I connect the tp-link to the hub do I use the micro usb.
The MINI USB port on the TPLink router is for powering the TPLink.
Not sure about the rest as I am using one of these for a WAP (wifi access point)
Cheers
Ok I need putting straight on some things.
1, the miner has a mirco usb port that connects to the hub.
2, the tp-link has 2 usb ports and a lan port, 1 micro usb and one male usb. the micro is for power how do I connect the tp-link to the hub do I use the micro usb.
1, the miner has a mirco usb port that connects to the hub.
2, the tp-link has 2 usb ports and a lan port, 1 micro usb and one male usb. the micro is for power how do I connect the tp-link to the hub do I use the micro usb.
Zich,
This difficulty which i can use in the settings of several miners, what is it exactly for?
i understand the difficulty of a mining pool, but when i look at it, this looks like its an another kind of diffuculty.
am i right here?
This difficulty which i can use in the settings of several miners, what is it exactly for?
i understand the difficulty of a mining pool, but when i look at it, this looks like its an another kind of diffuculty.
am i right here?
Jump to: