PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux) - page 154.

dvdjohn

newbie

Activity: 12

Merit: 0

Guys, how much MHs of hashrate should i expect with Phoenix miner for single Gtx 1070 gpu without overclocking and memory pills?

soda37

jr. member

Activity: 63

Merit: 1

Quote from: socks435 on December 29, 2020, 04:42:43 AM

It increase my hashrate a bit with 41mh/s and power 150w. I just want to run my miner with less power consumption. I just want to make profit than losing due to high Electricity rate here in my country.

Isn't it too low for 1080ti?

BTW I have pair of 1060 (#1,2) and 1080 (not Ti, card #3), with the following config:

-nvdo 1 -nvKernel 0 -straps 4,4,5 -powlim -25 -cclock +135,+135,+130 -cvddc 0 -mclock +520,+525,+675 -mvddc 0

They give me approx:

1: 23.504 MH/s 2: 22.850 MH/s 3: 35.792 MH/s

with the following consumption reported by phoenix miner:

36C 30% 89W, GPU2: 38C 30% 89W, GPU3: 47C 30% 150W

Calymore miner was giving me about 24+ MH/s on 1060 and 38+ on 1080 (with pill). Is there any better settings I can do with PhoenixMiner?

agabellini

newbie

Activity: 11

Merit: 0

Hello,

I'm trying to mine with Ubuntu 20.04 and a RX470, but I have some problems installing the AMD drivers.

I tried different versions, but I got always some errors when the installer compiles the kernel module.

I run the installer with "amdgpu-pro-install -y".

Is there any tricks? I'm missing some packages? Is there any guide?

Thanks,
Andrea

socks435

legendary

Activity: 2030

Merit: 1030

Privacy is always important

Quote from: Deafran on December 28, 2020, 11:18:55 PM

Quote from: socks435 on December 28, 2020, 11:13:57 AM

What's your total hashrate and power consumption for this setup?
Can you share your logs I'm looking for better setup for 1080ti. I'm actually paying high electricity and trying to setup my rig for power efficient.

using -straps 2

https://ibb.co/GtgJ72B

It shows around 220w it seems your living on low electricity rate or living in free Electricity?

Anyway, I tried your setup but I only add few of them

Code:

-powlim -20
-straps 5
-nvNew 1
-Rmode 1

It increase my hashrate a bit with 41mh/s and power 150w. I just want to run my miner with less power consumption. I just want to make profit than losing due to high Electricity rate here in my country.

adaseb

legendary

Activity: 3808

Merit: 1723

Up to 300% + 200 FS deposit bonuses

Quote from: IshReleX on December 29, 2020, 02:50:00 AM

Quote from: Wotan Wipeout on December 29, 2020, 01:53:53 AM

https://2miners.com/blog/how-to-mine-ethereum-and-ethereum-classic-on-4gb-gpus/

I followed everything there, and I am still getting 10-13s

Running on Windows, can anyone confirm that they are getting 20+ on Windows?

You need to switch to Linux and you can get 25MH/s, for another day. Then maybe 22-23MHs or so. If you are using Windows the speed will even be much much worse especially the higher that the DAG goes because Windows need more GDDR cached used up, Linux uses much much less.

You really aren't missing out. Profits are "ok", with $0.10 power the most you make is like $0.70 a day. So unless you got tons of these GPUs in your farm, just not worth the hassle to learn how to use a new OS just to get 1 GPU running for another couple of weeks. Best is to try and found an 8GB varient of the RX 470 and buy that instead and then you would get your 30MH/s speed back and the GPU would be worth more.

IshReleX

newbie

Activity: 5

Merit: 0

Quote from: Wotan Wipeout on December 29, 2020, 01:53:53 AM

https://2miners.com/blog/how-to-mine-ethereum-and-ethereum-classic-on-4gb-gpus/

I followed everything there, and I am still getting 10-13s

Running on Windows, can anyone confirm that they are getting 20+ on Windows?

Wotan Wipeout

member

Activity: 438

Merit: 27

https://2miners.com/blog/how-to-mine-ethereum-and-ethereum-classic-on-4gb-gpus/

IshReleX

newbie

Activity: 5

Merit: 0

What can I do to get 20mhs+ on my 4gb 570 cards?

I have been trying to mess with -daglim n however whenever I enter something it drops to 9mh/s, if i leave my .bat file the way it is, 4gb's get 13mhs and 8gb gets 29mh/s

https://i.imgur.com/AApQ7xx.png

Deafran

jr. member

Activity: 49

Merit: 4

Quote from: socks435 on December 28, 2020, 11:13:57 AM

Quote from: Deafran on December 26, 2020, 10:49:13 PM

here my bat file for my 1080ti

PhoenixMiner.exe -pool eth-eu2.nanopool.org:9999 -wal 0xxxxxx -worker Zinc -epsw x -mode 1 -powlim -20 -tt -85 -tmax 85 -cclock +100 -mclock +600 -straps 5 -ftime 55 -nvNew 1 -Rmode 1 -log 0 -mport 0 -etha 0 -retrydelay 1 -coin eth
pause

phoenixminer.exe-run as administrator
win10

and not using after burner

What's your total hashrate and power consumption for this setup?
Can you share your logs I'm looking for better setup for 1080ti. I'm actually paying high electricity and trying to setup my rig for power efficient.

using -straps 2

https://ibb.co/GtgJ72B

jblahus

newbie

Activity: 1

Merit: 0

Was wondering if phoenix miner supports asrock motherboards z490 chipset with clever access memory bios feature for AMD6800 series GPUs ? similar to AMD chipset motherboards with Smart access memory or resized bar. Thank you.

Erupthis

newbie

Activity: 4

Merit: 0

Hello all. I have problem with phoneix dual mining. Not working Sad

My config:

Code:

-pool ssl://eu1.ethermine.org:5555
-pool2 ssl://us1.ethermine.org:5555
-wal ETH WALLET
-rvram -1
-epsw x
-mode 0
-dbg -1
-tmax 75
-cclock 1200
-cvddc 850
-mclock 1100
-powlim 30
-mvddc 850

-eres 0

-dpool stratum+tcp://blake2s.usa.nicehash.com:3361
-dwal BTC Wallet
-proto 4

I try change -proto 4 to -proto 3 but notching help.

https://i.ibb.co/sRMtRtG/problem-eth.jpg

Any idea?

Edit:

My gfx is Radeon Vega 64

fr4nkthetank

legendary

Activity: 2294

Merit: 1182

Now the money is free, and so the people will be

1080ti, why not use msi afterburner, ctrl+f, set to lowest voltage you can without instant crash @ core clock that hashes ok, maybe 875v 1800 (off the top of my head, experiment). press L i think to lock the gpu at that voltage/clock. cant really get better than that I think

groovytechno

newbie

Activity: 49

Merit: 0

Quote from: Deafran on December 27, 2020, 10:31:18 PM

Quote from: groovytechno on December 27, 2020, 12:09:06 PM

Quote from: Deafran on December 26, 2020, 10:31:34 PM

Quote from: groovytechno on December 26, 2020, 11:51:04 AM

For my 1000 mh/s Nanopool shows that i receive 0.04526 ETH per day.

My concern is that my current and average hashrate at the pool-side is always hovering between 520-740 mh/s while the reported hashrate is accurate at 950-1000 mh/s

Mining ETC has no issue with this at all. Average hashrate is pretty spot on with my reported hashrate.

yeah, its a bit low (0.04526)

i got 0.17343 - 0.18 xxx for 3Gh/s, some time can be 0.2xxxx ETH per day
2 month ago can reach 0.25xxx ETH per day

Interesting. Mind if I ask what pool and mining software you're using?

eth-asia1.nanopool.org

3 rig with ethminer and other with PhoenixMiner (since claymore cant mining)

mostly ethOS only 3 rig using W10(PhoenixMiner)

Thank you for your time and info!

socks435

legendary

Activity: 2030

Merit: 1030

Privacy is always important

Quote from: Deafran on December 26, 2020, 10:49:13 PM

here my bat file for my 1080ti

PhoenixMiner.exe -pool eth-eu2.nanopool.org:9999 -wal 0xxxxxx -worker Zinc -epsw x -mode 1 -powlim -20 -tt -85 -tmax 85 -cclock +100 -mclock +600 -straps 5 -ftime 55 -nvNew 1 -Rmode 1 -log 0 -mport 0 -etha 0 -retrydelay 1 -coin eth
pause

phoenixminer.exe-run as administrator
win10

and not using after burner

What's your total hashrate and power consumption for this setup?
Can you share your logs I'm looking for better setup for 1080ti. I'm actually paying high electricity and trying to setup my rig for power efficient.

buraz11

jr. member

Activity: 115

Merit: 4

skinnyfalcon i have on my 3060ti s and newest phoenixminer, but also gminer, random times

theerachate.p

newbie

Activity: 15

Merit: 0

Quote from: matmator on December 27, 2020, 05:20:24 PM

Quote from: theerachate.p on December 27, 2020, 03:34:35 PM

Quote from: matmator on December 27, 2020, 02:17:02 PM

hello, since the last update, my gpu memory setting no longer works,

here is my .bat: PhoenixMiner.exe -pool eth-eu1.nanopool.org:9999 -wal 0x24kndflog2588dlE288CA7eF03b627D0C78758426.pc -powlim 75 -mclock 4500 -log 0

https://nsa40.casimages.com/img/2020/12/27/201227072312451120.png

never use parameters to set your overclocking, use third party software is much more stable

don't say anything please! I always did, never had a problem!

Yeah, and this guy is having a problem using in-miner overclocking tools, see how it turned out for him. I'm just saying, switch to Afterburner or Precision would do the trick as you have much more control of the card than the in-miner tools do. It's awesome for linux users, but if you decided to go Windows then I highly recommend using something else

skinnyfalcon

newbie

Activity: 49

Merit: 0

Anyone started seeing TDR error on blue screen of death??

Deafran

jr. member

Activity: 49

Merit: 4

Quote from: groovytechno on December 27, 2020, 12:09:06 PM

Quote from: Deafran on December 26, 2020, 10:31:34 PM

Quote from: groovytechno on December 26, 2020, 11:51:04 AM

For my 1000 mh/s Nanopool shows that i receive 0.04526 ETH per day.

My concern is that my current and average hashrate at the pool-side is always hovering between 520-740 mh/s while the reported hashrate is accurate at 950-1000 mh/s

Mining ETC has no issue with this at all. Average hashrate is pretty spot on with my reported hashrate.

yeah, its a bit low (0.04526)

i got 0.17343 - 0.18 xxx for 3Gh/s, some time can be 0.2xxxx ETH per day
2 month ago can reach 0.25xxx ETH per day

Interesting. Mind if I ask what pool and mining software you're using?

eth-asia1.nanopool.org

3 rig with ethminer and other with PhoenixMiner (since claymore cant mining)

mostly ethOS only 3 rig using W10(PhoenixMiner)

hesido

jr. member

Activity: 158

Merit: 5

With all these low-life scammers trying to post links to malware, I think there should be an option to forbid new accounts to post links, or any text that looks like link in case they still do it without the proper tags.

Bug Report:
I think I have encountered a bug;
When you use auto-tuning, and change a few parameters on some of the gpu's in config (but not all), the ones that the parameters changed are applied previous GT values, but the rest of the cards are reset to default tuning values and hashrates of those cards drop significantly. The remedy is restarting miner or re-starting tuning. The fix should be easy, just make sure to re-apply previous known tuning values to ALL cards. Better yet, if auto-tuning is on, the cards that have their clock settings change should go back into auto-tune mode, while the rest could stay as is, instead of re-applying last known tuning parameter.

batsonxl

member

Activity: 1201

Merit: 26

Quote from: matmator on December 27, 2020, 05:19:14 PM

Quote from: batsonxl on December 27, 2020, 04:30:32 PM

Quote from: matmator on December 27, 2020, 02:17:02 PM

hello, since the last update, my gpu memory setting no longer works,

here is my .bat: PhoenixMiner.exe -pool eth-eu1.nanopool.org:9999 -wal 0x24kndflog2588dlE288CA7eF03b627D0C78758426.pc -powlim 75 -mclock 4500 -log 0

Mclock 4500? what card is that?

1070 ti

nvidia cards you have to write -mclock +400 for increase +400. amd cards uses direct numer like 2150.

Topic: PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux) - page 154. (Read 784857 times)