PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux) - page 51.

deedeeranged

member

Activity: 325

Merit: 42

Hi all,

I am running Debian testing/bullseye and have a KFA2 GTX 1070 OC SNPR and can get only abt 25MH/s with ethash.
My command line is: sudo ./PhoenixMiner -nvidia -proto 3 -cdm 1 -prate 0.0703 -coin eth -pool ssl://eu1.ethermine.org:5555 -wal
Have looking at different settings to see if I can get abt. 30MH/s or more but I get confused by all the settings.
Has anyone any sugggestions to help me out.

Thx in advance.

oblivionxt

newbie

Activity: 13

Merit: 2

Quote from: Tarumahr on June 23, 2021, 05:15:51 AM

What's the best setting for the AMD RX 6900 XT ?

As far as I know, the settings are the same for the 6800, 6800 XT, and 6900 XT.

Lower the frequency to 1400 to 1600 at 793mv, make sure it's stable of course.

Turn on Fast Timing for the memory, then run the memory at 2100 to 2150, once again whatever is stable.

Should net you 64+ MH/s at 135W.

Also, if you have a display attached to the card, you'll have to lower the -mi (mining intensity). The driver can crash out (assuming you're in windows), my card lost a very small amount of hash at -mi 4, but became 100% stable.

Tarumahr

newbie

Activity: 1

Merit: 0

What's the best setting for the AMD RX 6900 XT ?

crazykat8091

newbie

Activity: 4

Merit: 0

Quote from: Targonis on June 22, 2021, 08:50:58 PM

It looks like Radeon Software 21.6.1 is not compatible with PhoenixMiner 5.6d with the Radeon 6800. I've gotten reports that the 5700XT is fine with the new driver, but my 6800 keeps causing a fatal error when trying to start mining. Single GPU in the system, so nothing else to cause conflicts.

Try -clKernel 0 I have no issue with new driver with all 6800XT 6800 5700XT RX580. Wait until new version that officially support new driver then change it back to 1.

Targonis

jr. member

Activity: 56

Merit: 13

It looks like Radeon Software 21.6.1 is not compatible with PhoenixMiner 5.6d with the Radeon 6800. I've gotten reports that the 5700XT is fine with the new driver, but my 6800 keeps causing a fatal error when trying to start mining. Single GPU in the system, so nothing else to cause conflicts.

Targonis

jr. member

Activity: 56

Merit: 13

Quote from: SamaelDNM on June 22, 2021, 01:40:19 AM

I got a new drive from amd and is it giving an error, any ideas?

What GPU and drivers are you using?

dazmann

jr. member

Activity: 45

Merit: 6

Quote from: SamaelDNM on June 22, 2021, 01:40:19 AM

I got a new drive from amd and is it giving an error, any ideas?

Very likely new driver is not supported. Go back to 21.4.1 to continue mining and wait for a new version of PM with driver support to be released.

batsonxl

member

Activity: 1208

Merit: 27

Quote from: miner29 on June 22, 2021, 09:32:59 AM

Quote from: batsonxl on June 22, 2021, 06:18:53 AM

Is there any way ETH+ZIL mining simultaneously, I dont liked idea it stops mining eth and mines zil. It is not like used to be like dual mining in the past.

Its how ZIL works. Is not like the old dual mining where it actually occurred at the same time.

ok thanks for reply

miner29

full member

Activity: 1281

Merit: 141

Quote from: batsonxl on June 22, 2021, 06:18:53 AM

Is there any way ETH+ZIL mining simultaneously, I dont liked idea it stops mining eth and mines zil. It is not like used to be like dual mining in the past.

Its how ZIL works. Is not like the old dual mining where it actually occurred at the same time.

batsonxl

member

Activity: 1208

Merit: 27

Is there any way ETH+ZIL mining simultaneously, I dont liked idea it stops mining eth and mines zil. It is not like used to be like dual mining in the past.

sxemini

member

Activity: 1558

Merit: 69

Quote from: makipsee on June 21, 2021, 02:27:09 PM

Fairly new to mining but been using PM. I'm now starting to dual mine ETH + ZIL on the Ezil.me pools. Does anyone know I have a RX580 for both and a gtx 1050 2GB that can mine ZIL. My question is if there is a way to use the RX while mining ETH and switch to both card for the ZIL change over?

Thank you

Yes i think you can do it with lolminer for example.

Mozart Andrey

newbie

Activity: 1

Merit: 0

Hello, so I usually see phoenixminer’s console on windows or other with color or if i go to the miner log, but when ever i launch the HIVE SHELL and a type miner, everything is in black and white ?
Is there a way to see the normal color output in HiveOS?

https://c.radikal.ru/c18/2106/58/1ed63f0364be.jpg

https://a.radikal.ru/a25/2106/27/47a11720aeac.jpg

swogerino

legendary

Activity: 3318

Merit: 1247

Bitcoin Casino Est. 2013

Quote from: Targonis on June 21, 2021, 07:03:29 AM

Quote from: swogerino on June 20, 2021, 02:57:59 PM

The Powercolor Red Devil Rx 6800 XT,if power for example goes down,or internet doesn't work for some minutes,the miner completely crash one card or two and I have to make a few restarts before they stabilize.After stabilizing they work great for days without interruption if no power outages or internet connection problems.Can you fix this in the upcoming version?

That sounds more like a BIOS or power supply problem with the computer. Check your overclock settings, but your power supply may have degraded. I have some issues with a RAID controller where it won't pick up one of my hard drives after a cold boot, and while adding a POST delay to give it extra time to power up the drives would probably fix it, I generally just reboot 2-3 times until the controller sees the one drive that falls off the array. If you don't have enough power for the video cards though,that could also cause your problems.

It was bad overclock settings,I was using Core Clock of 2329 when the recommended for mining it was 1200.Also change Core Voltage to 880 from 1150 which was also wrong for mining,and lastly switched memory clock to the max of 2150.It was doing 59 mhsh before and crashing time after time,after making the modifications it runs at lower power consumption 160 watt from 225 watt and makes 64 mhsh,also is running stable from 18 hours now.My PSU is in top condition as I am using a Corsair 1000 watt on a board which consumes in total 550 watt.Also no BIOS problem.

bategojko74

member

Activity: 220

Merit: 12

Quote from: ?? on ??

The new beta version is finally ready. You can download PhoenixMiner 5.7a from here:

Get out troll. ADMINISTRATORS PLEASE BAN THIS ACCOUNT!!!

SamaelDNM

member

Activity: 732

Merit: 18

New exchange generation

I got a new drive from amd and is it giving an error, any ideas?

makipsee

newbie

Activity: 28

Merit: 7

Fairly new to mining but been using PM. I'm now starting to dual mine ETH + ZIL on the Ezil.me pools. Does anyone know I have a RX580 for both and a gtx 1050 2GB that can mine ZIL. My question is if there is a way to use the RX while mining ETH and switch to both card for the ZIL change over?

Thank you

sxemini

member

Activity: 1558

Merit: 69

Quote from: abg00 on June 21, 2021, 08:12:11 AM

Quote from: Targonis on June 21, 2021, 07:05:20 AM

Quote from: abg00 on June 20, 2021, 02:03:51 PM

plz add amd 6800 6900 native kernel support plz

have error unable to set straps - unsupported GPU

What version of PhoenixMiner are you running, and what operating system? PhoenixMiner 5.6d(see first post for information), won't be the problem, but drivers could easily be the problem.

last 5.6d
win10
driver 21.3.1
miner work with error

Use teamredminer and you get the best hashrate poolside. Tested and confirmed by so much people.

abg00

jr. member

Activity: 288

Merit: 1

Quote from: Targonis on June 21, 2021, 07:05:20 AM

Quote from: abg00 on June 20, 2021, 02:03:51 PM

plz add amd 6800 6900 native kernel support plz

have error unable to set straps - unsupported GPU

What version of PhoenixMiner are you running, and what operating system? PhoenixMiner 5.6d(see first post for information), won't be the problem, but drivers could easily be the problem.

last 5.6d
win10
driver 21.3.1
miner work with error

Targonis

jr. member

Activity: 56

Merit: 13

Quote from: abg00 on June 20, 2021, 02:03:51 PM

plz add amd 6800 6900 native kernel support plz

have error unable to set straps - unsupported GPU

What version of PhoenixMiner are you running, and what operating system? PhoenixMiner 5.6d(see first post for information), won't be the problem, but drivers could easily be the problem.

Targonis

jr. member

Activity: 56

Merit: 13

Quote from: swogerino on June 20, 2021, 02:57:59 PM

The Powercolor Red Devil Rx 6800 XT,if power for example goes down,or internet doesn't work for some minutes,the miner completely crash one card or two and I have to make a few restarts before they stabilize.After stabilizing they work great for days without interruption if no power outages or internet connection problems.Can you fix this in the upcoming version?

That sounds more like a BIOS or power supply problem with the computer. Check your overclock settings, but your power supply may have degraded. I have some issues with a RAID controller where it won't pick up one of my hard drives after a cold boot, and while adding a POST delay to give it extra time to power up the drives would probably fix it, I generally just reboot 2-3 times until the controller sees the one drive that falls off the array. If you don't have enough power for the video cards though,that could also cause your problems.

Topic: PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux) - page 51. (Read 784985 times)