Pages:
Author

Topic: Re: [ANN] Technobit HEX16A2 - 24 Ghs - 50 EUR 48 h shippment - page 27. (Read 104895 times)

legendary
Activity: 1190
Merit: 1000
Hi

Has anyone got these working using cgminer 3.10 on win 7?

I have got them running on hexminer but I am a bit worried that my anti virus shows hex as having a virus and I have just had 0.1621 stolen from my bitcoin wallet

Hi mudge,

The cgminer patch for detecting HEX16 only work on linux. So on windows 7 only HEXMINER available right now.
Or you can use virtual pc installed on win7 to run linux. I already test this with HEX16C.
https://bitcointalksearch.org/topic/m.4198171

But the best way is to use TPLINK TL-MR3020 as host, but then you will need separate PSU ofc.
Feel free to ask us here about the setup  Grin
legendary
Activity: 1190
Merit: 1000
Hello Zich,

Can i ask you for help, i'm really lost. Huh
I just got my miners yesterday, and i'm suffering a lot to make them working.
Thanks
Bestalg

Hi bestalg,

Very sorry to not respond in time since i am only online from 01:00 - 14:00 UTC.

Like loshia said, i think you should buy single rail PSU, so you don't had to worry about rail maximum load  Grin
Antec HCG Series HCG-900W is four rail.

member
Activity: 92
Merit: 10
Hi

Has anyone got these working using cgminer 3.10 on win 7?

I have got them running on hexminer but I am a bit worried that my anti virus shows hex as having a virus and I have just had 0.1621 stolen from my bitcoin wallet
newbie
Activity: 43
Merit: 0
newbie
Activity: 26
Merit: 0
you should connect the 24pin atx connector and put in a paperclip or a little piece of power cable in the green and black wire like in the picture , i`don`t know if your fan is going to spin i think it will i have corsair cx 750m and when i put in a paperclip in my green and black wire the fan spins without even connecting any device to the psu..

http://s8.postimg.org/z174nra3l/download.jpg

so do this:
disconnect the psu from the wall socket
connect 24 pin atx
put paperclip in green and black wire
put some electrical tape on top of the paperclip (24 pin connector)
make shure every thing is connected to the HEXc
power on psu
happy hashing
newbie
Activity: 43
Merit: 0
On the picture you see your hexc fan spinning , while your fan of your psu looks like it's doing nothing .
Just a question , did you short your psu (like putting a paperclip on the green and black wire ?
If the hexc get's 12volt the red led wil be  blinking

(Pardon my english)
I have a corsair rm750 which has 0rpm mode with the fan if less than 40% of total watt is used.
Should the fans spin when i only plug them into the psu?
Ok just read about shorting the PSU howevr all my wires are black edit: youtube saved me..
http://i39.tinypic.com/j8czrr.jpg
full member
Activity: 199
Merit: 100
On the picture you see your hexc fan spinning , while your fan of your psu looks like it's doing nothing .
Just a question , did you short your psu (like putting a paperclip on the green and black wire ?
If the hexc get's 12volt the red led wil be  blinking

(Pardon my english)
That may be his problem, looks like he only has a 12V rail connected. I can't see the 20+4 MB connector, you would need to attach that to the PSU and short the PS ON pin.
newbie
Activity: 26
Merit: 0
On the picture you see your hexc fan spinning , while your fan of your psu looks like it's doing nothing .
Just a question , did you short your psu (like putting a paperclip on the green and black wire ?
If the hexc get's 12volt the red led wil be  blinking

(Pardon my english)
newbie
Activity: 43
Merit: 0
Hey Guys,
I still cant gey my miners up and running. I have connected one miner now to the technobit tplink router and this is all that happens.
I have the feeling that i am making a noob mistake somewhere but i just can't figure it out.
Who can help?

http://i41.tinypic.com/2rp626e.jpg
Here are my settings:
http://i41.tinypic.com/4zuk42.png
There is no 12v power supply to the board. Double check it. Is molex connected and ok? Are you using some extension cable to molex?

This is my setup:
The hex16 has a red and a yellow led lit.
http://i42.tinypic.com/znwwy.jpg
legendary
Activity: 1610
Merit: 1000
Hey Guys,
I still cant gey my miners up and running. I have connected one miner now to the technobit tplink router and this is all that happens.
I have the feeling that i am making a noob mistake somewhere but i just can't figure it out.
Who can help?


Here are my settings:

There is no 12v power supply to the board. Double check it. Is molex connected and ok? Are you using some extension cable to molex?
newbie
Activity: 49
Merit: 0
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

...
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.
...
Thanks



My first thought from reading that is that your boards are being starved of power as you connect more. Have you tried running each one singularly to make sure they perform okay. Then try them together on different power sources (if you have two or more PSU's available), so you've got PSU one to board one, and PSU two to board two etc, and let us know the results. What settings are you using in Hexminer, can you post a screenshot?

It's seems power issue but 2 of 500w psu connecting 4 boards only.


What is the make model of your power supply? It's probably got multiple low amp rails.

I use 350w Enermax PSUs they have 2 power rails and 4x molex on 3 seperate wires and only cost <£30/$40 they run 4x Hex16B no problem.

CIRCLE RAW POWER 500 WATT

Hard to find any info on this PSU I could only find this graphic in the Google cache as originals seem to be deleted from their web site.
If correct it may have only 28A x 12V = 336W on the 12v rail.
Quote
But their web site says it's dual 12v rails so maybe it's 335W/2 = 168W max on a single rail/wire.
That would explain why it's only powering 2x Hex16B.
Never mix the ground between psu's never.
Use one psu hub powers from it and as menu boards you can + tplink and forget

Any way, i have 10 boards to feed tomorrow and im going to buy : Antec HCG Series HCG-900W
I think it will be enough for all, with 4 x 12v rails and 8 morlex and i will use 2 other molex from the other PSU.

1chose a single rail psu with 60 amps at 12w rail something like 750-800 w
Watch the 12 w rail
Buy a tplink and if you can order the hub mentioned in my post from amazon.de if you are German
I can send you the link later for the hub if you want
I have 9 boards to 700 w psu with 20 days uptime + tplink when done right
I am changing the software two often Smiley Wink
Throw away 5v tpli k adapter + hub 5v adapter also

Thanks Loshia,
I will let you know, tomorrow
newbie
Activity: 43
Merit: 0
Hey Guys,
I still cant gey my miners up and running. I have connected one miner now to the technobit tplink router and this is all that happens.
I have the feeling that i am making a noob mistake somewhere but i just can't figure it out.
Who can help?

http://i41.tinypic.com/2rp626e.jpg
Here are my settings:
http://i41.tinypic.com/4zuk42.png
newbie
Activity: 43
Merit: 0
Hey Guys,
I still cant gey my miners up and running. I have connected one miner now to the technobit tplink router and this is all that happens.
I have the feeling that i am making a noob mistake somewhere but i just can't figure it out.
Who can help?

http://i41.tinypic.com/2rp626e.jpg
legendary
Activity: 1610
Merit: 1000
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

...
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.
...
Thanks


My first thought from reading that is that your boards are being starved of power as you connect more. Have you tried running each one singularly to make sure they perform okay. Then try them together on different power sources (if you have two or more PSU's available), so you've got PSU one to board one, and PSU two to board two etc, and let us know the results. What settings are you using in Hexminer, can you post a screenshot?

It's seems power issue but 2 of 500w psu connecting 4 boards only.


What is the make model of your power supply? It's probably got multiple low amp rails.

I use 350w Enermax PSUs they have 2 power rails and 4x molex on 3 seperate wires and only cost <£30/$40 they run 4x Hex16B no problem.

CIRCLE RAW POWER 500 WATT

Hard to find any info on this PSU I could only find this graphic in the Google cache as originals seem to be deleted from their web site.
If correct it may have only 28A x 12V = 336W on the 12v rail.
Quote
But their web site says it's dual 12v rails so maybe it's 335W/2 = 168W max on a single rail/wire.
That would explain why it's only powering 2x Hex16B.
Never mix the ground between psu's never.
Use one psu hub powers from it and as menu boards you can + tplink and forget

Any way, i have 10 boards to feed tomorrow and im going to buy : Antec HCG Series HCG-900W
I think it will be enough for all, with 4 x 12v rails and 8 morlex and i will use 2 other molex from the other PSU.

1chose a single rail psu with 60 amps at 12w rail something like 750-800 w
Watch the 12 w rail
Buy a tplink and if you can order the hub mentioned in my post from amazon.de if you are German
I can send you the link later for the hub if you want
I have 9 boards to 700 w psu with 20 days uptime + tplink when done right
I am changing the software two often Smiley Wink
Throw away 5v tpli k adapter + hub 5v adapter also
newbie
Activity: 49
Merit: 0
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

...
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.
...
Thanks


My first thought from reading that is that your boards are being starved of power as you connect more. Have you tried running each one singularly to make sure they perform okay. Then try them together on different power sources (if you have two or more PSU's available), so you've got PSU one to board one, and PSU two to board two etc, and let us know the results. What settings are you using in Hexminer, can you post a screenshot?

It's seems power issue but 2 of 500w psu connecting 4 boards only.


What is the make model of your power supply? It's probably got multiple low amp rails.

I use 350w Enermax PSUs they have 2 power rails and 4x molex on 3 seperate wires and only cost <£30/$40 they run 4x Hex16B no problem.

CIRCLE RAW POWER 500 WATT

Hard to find any info on this PSU I could only find this graphic in the Google cache as originals seem to be deleted from their web site.
If correct it may have only 28A x 12V = 336W on the 12v rail.
Quote
But their web site says it's dual 12v rails so maybe it's 335W/2 = 168W max on a single rail/wire.
That would explain why it's only powering 2x Hex16B.
Never mix the ground between psu's never.
Use one psu hub powers from it and as menu boards you can + tplink and forget

Any way, i have 10 boards to feed tomorrow and im going to buy : Antec HCG Series HCG-900W
I think it will be enough for all, with 4 x 12v rails and 8 morlex and i will use 2 other molex from the other PSU.
legendary
Activity: 1610
Merit: 1000
this is what i get right now

[Firmware Version] => 20140113
cgminer: 3_10_0_87f0213
Socket connect failed: Connection refused

http://www.bilder-upload.eu/upload/abe0a0-1389717975.jpg

not sure what is wrong, just connected all my boards to powered usb and tp-link

Ok it seems like its working now, just changed the worker, strange.
Nevertheless, as i mentioned before, one board only running with around 14GH/s, so it seems some chips are damaged
Code:
[STATS0] =>
(
   [STATS] => 0
   [ID] => HEXc0
   [Enabled] => Y
   [Status] => Alive
   [Elapsed] => 499
   [MHS 5s] => 13.83G
   [MHS av] => 14.45G
   [Hardware Errors] => 44
   [Hardware Errors%] => 2.5552
   [USB Read Errors] => 0
   [USB Write Errors] => 0
   [Idled for 60 sec] => 0
   [Reset Count] => 0
   [Last Share Time] => 1389718295
   [Chip Count] => 16
   [Frequency] => 1500
   [Core Voltage] => 1100
   [PIC Voltage Readings] => 1108
   [Chip1 Nonces] => 11
   [Chip1 Dupes] => 0
   [Chip2 Nonces] => 0
   [Chip2 Dupes] => 0
   [Chip3 Nonces] => 0
   [Chip3 Dupes] => 0
   [Chip4 Nonces] => 0
   [Chip4 Dupes] => 0
   [Chip5 Nonces] => 0
   [Chip5 Dupes] => 0
   [Chip6 Nonces] => 159
   [Chip6 Dupes] => 0
   [Chip7 Nonces] => 167
   [Chip7 Dupes] => 0
   [Chip8 Nonces] => 148
   [Chip8 Dupes] => 0
   [Chip9 Nonces] => 57
   [Chip9 Dupes] => 0
   [Chip10 Nonces] => 163
   [Chip10 Dupes] => 0
   [Chip11 Nonces] => 166
   [Chip11 Dupes] => 0
   [Chip12 Nonces] => 167
   [Chip12 Dupes] => 0
   [Chip13 Nonces] => 152
   [Chip13 Dupes] => 0
   [Chip14 Nonces] => 153
   [Chip14 Dupes] => 0
   [Chip15 Nonces] => 169
   [Chip15 Dupes] => 0
   [Chip16 Nonces] => 166
   [Chip16 Dupes] => 0

Does those nonces = 0 mean they are not working or damaged?
Maybe you can help Marto
Thanks!
Smells like dead chips to me
legendary
Activity: 1610
Merit: 1000
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

...
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.
...
Thanks


My first thought from reading that is that your boards are being starved of power as you connect more. Have you tried running each one singularly to make sure they perform okay. Then try them together on different power sources (if you have two or more PSU's available), so you've got PSU one to board one, and PSU two to board two etc, and let us know the results. What settings are you using in Hexminer, can you post a screenshot?

It's seems power issue but 2 of 500w psu connecting 4 boards only.


What is the make model of your power supply? It's probably got multiple low amp rails.

I use 350w Enermax PSUs they have 2 power rails and 4x molex on 3 seperate wires and only cost <£30/$40 they run 4x Hex16B no problem.

CIRCLE RAW POWER 500 WATT

Hard to find any info on this PSU I could only find this graphic in the Google cache as originals seem to be deleted from their web site.
If correct it may have only 28A x 12V = 336W on the 12v rail.
Quote
But their web site says it's dual 12v rails so maybe it's 335W/2 = 168W max on a single rail/wire.
That would explain why it's only powering 2x Hex16B.
Never mix the ground between psu's never.
Use one psu hub powered fom it and as many boards as you can + tplink and forget. In your case yo can connect al four to the mentioned if yo spread the load each bit fury board eats 5amps max oc at 12v
hero member
Activity: 490
Merit: 500
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

...
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.
...
Thanks


My first thought from reading that is that your boards are being starved of power as you connect more. Have you tried running each one singularly to make sure they perform okay. Then try them together on different power sources (if you have two or more PSU's available), so you've got PSU one to board one, and PSU two to board two etc, and let us know the results. What settings are you using in Hexminer, can you post a screenshot?

It's seems power issue but 2 of 500w psu connecting 4 boards only.


What is the make model of your power supply? It's probably got multiple low amp rails.

I use 350w/450w Enermax PSUs they spread the molex on 3 seperate wires and only cost <£30/$40 they run 3x/4x Hex16B no problem.

CIRCLE RAW POWER 500 WATT

Hard to find any info on this PSU I could only find this graphic in the Google cache as originals seem to be deleted from their web site.
If correct it may have only 28A x 12V = 336W on the 12v rail.
Quote
But their web site says it's dual 12v rails so maybe it's 335W/2 = 168W max on a single rail/wire.
That would explain why it's only powering 2x Hex16B.
newbie
Activity: 49
Merit: 0
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

...
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.
...
Thanks


My first thought from reading that is that your boards are being starved of power as you connect more. Have you tried running each one singularly to make sure they perform okay. Then try them together on different power sources (if you have two or more PSU's available), so you've got PSU one to board one, and PSU two to board two etc, and let us know the results. What settings are you using in Hexminer, can you post a screenshot?

It's seems power issue but 2 of 500w psu connecting 4 boards only.


What is the make model of your power supply? It's probably got multiple low amp rails.

I use 350w Enermax PSUs they have 2 power rails and 4x molex on 3 seperate wires and only cost <£30/$40 they run 4x Hex16B no problem.

CIRCLE RAW POWER 500 WATT
hero member
Activity: 490
Merit: 500
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

...
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.
...
Thanks


My first thought from reading that is that your boards are being starved of power as you connect more. Have you tried running each one singularly to make sure they perform okay. Then try them together on different power sources (if you have two or more PSU's available), so you've got PSU one to board one, and PSU two to board two etc, and let us know the results. What settings are you using in Hexminer, can you post a screenshot?

It's seems power issue but 2 of 500w psu connecting 4 boards only.


What is the make model of your power supply? It's probably got multiple low amp rails or all the molex on one wire.

I use 350w/450w Enermax PSUs they spread the molex on 3 seperate wires and only cost <£30/$40 they run 3x/4x Hex16B no problem.
Pages:
Jump to: