Pages:
Author

Topic: Re: [ANN] Technobit HEX16A2 - 24 Ghs - 50 EUR 48 h shippment - page 28. (Read 104895 times)

newbie
Activity: 49
Merit: 0
Quote
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor

Do you have Hex16B or Hex16A2 (Hex16C)?

This is the Hex16A2 (Hex16C) thread and 4x 24GH would be 96GH+ so 101 GH seems normal.

If they are Hex16B don't run them all on the same length of wire because you will be using the same PSU rail.

Yes you are Right It's Hex16B, but i was looking for Zich, just asking him a proper tutorial of tplink method.
you are welkome to help.
thanks
newbie
Activity: 49
Merit: 0
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

...
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.
...
Thanks


My first thought from reading that is that your boards are being starved of power as you connect more. Have you tried running each one singularly to make sure they perform okay. Then try them together on different power sources (if you have two or more PSU's available), so you've got PSU one to board one, and PSU two to board two etc, and let us know the results. What settings are you using in Hexminer, can you post a screenshot?

It's seems power issue but 2 of 500w psu connecting 4 boards only.
hero member
Activity: 490
Merit: 500
Quote
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor

Do you have Hex16B or Hex16A2 (Hex16C)?

This is the Hex16A2 (Hex16C) thread and 4x 24GH would be 96GH+ so 101 GH seems normal.

If they are Hex16B don't run them all on the same length of wire because you will be using the same PSU rail.
sr. member
Activity: 291
Merit: 250
Scam-Busting PSA: Beware of Black Arrow Software
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

...
So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.
...
Thanks


My first thought from reading that is that your boards are being starved of power as you connect more. Have you tried running each one singularly to make sure they perform okay. Then try them together on different power sources (if you have two or more PSU's available), so you've got PSU one to board one, and PSU two to board two etc, and let us know the results. What settings are you using in Hexminer, can you post a screenshot?
member
Activity: 77
Merit: 10
this is what i get right now

[Firmware Version] => 20140113
cgminer: 3_10_0_87f0213
Socket connect failed: Connection refused

http://www.bilder-upload.eu/upload/abe0a0-1389717975.jpg

not sure what is wrong, just connected all my boards to powered usb and tp-link

Ok it seems like its working now, just changed the worker, strange.
Nevertheless, as i mentioned before, one board only running with around 14GH/s, so it seems some chips are damaged
Code:
[STATS0] =>
(
   [STATS] => 0
   [ID] => HEXc0
   [Enabled] => Y
   [Status] => Alive
   [Elapsed] => 499
   [MHS 5s] => 13.83G
   [MHS av] => 14.45G
   [Hardware Errors] => 44
   [Hardware Errors%] => 2.5552
   [USB Read Errors] => 0
   [USB Write Errors] => 0
   [Idled for 60 sec] => 0
   [Reset Count] => 0
   [Last Share Time] => 1389718295
   [Chip Count] => 16
   [Frequency] => 1500
   [Core Voltage] => 1100
   [PIC Voltage Readings] => 1108
   [Chip1 Nonces] => 11
   [Chip1 Dupes] => 0
   [Chip2 Nonces] => 0
   [Chip2 Dupes] => 0
   [Chip3 Nonces] => 0
   [Chip3 Dupes] => 0
   [Chip4 Nonces] => 0
   [Chip4 Dupes] => 0
   [Chip5 Nonces] => 0
   [Chip5 Dupes] => 0
   [Chip6 Nonces] => 159
   [Chip6 Dupes] => 0
   [Chip7 Nonces] => 167
   [Chip7 Dupes] => 0
   [Chip8 Nonces] => 148
   [Chip8 Dupes] => 0
   [Chip9 Nonces] => 57
   [Chip9 Dupes] => 0
   [Chip10 Nonces] => 163
   [Chip10 Dupes] => 0
   [Chip11 Nonces] => 166
   [Chip11 Dupes] => 0
   [Chip12 Nonces] => 167
   [Chip12 Dupes] => 0
   [Chip13 Nonces] => 152
   [Chip13 Dupes] => 0
   [Chip14 Nonces] => 153
   [Chip14 Dupes] => 0
   [Chip15 Nonces] => 169
   [Chip15 Dupes] => 0
   [Chip16 Nonces] => 166
   [Chip16 Dupes] => 0

Does those nonces = 0 mean they are not working or damaged?
Maybe you can help Marto
Thanks!
member
Activity: 77
Merit: 10
this is what i get right now

[Firmware Version] => 20140113
cgminer: 3_10_0_87f0213
Socket connect failed: Connection refused

http://www.bilder-upload.eu/upload/abe0a0-1389717975.jpg

not sure what is wrong, just connected all my boards to powered usb and tp-link
newbie
Activity: 49
Merit: 0
After the 3 day in town delivery UPS finally get you Wink
May I can try helping

Dear Martin,

Yes I just checked the package, and simply every thing was perfect.
Thank You, you Promised me and you did, but without tracking number, doesn't matter.

any way to be honest i was expecting tomorrow because we had a holiday Sunday so Tuesday or Wednesday, but i'm so happy finally ii's arrived.
I know the type of the pressure you have, because i have similar business, Hope every one will get his ambitions and goals, in this year.

Any way
I have 8 tower of (16 bitfury boards) from asic-hardware working from months,never touch it from the first day, not interrupted at all.
connected to laptop with cgminer win7.

also 10 hashbuster (9 bitfury board) conected also to another laptop.

So i tried your boards with hexmine in win7, tried all the combinations got 42gh with one board, 77ghs with two, 91gh with three, 101gh with foor
it's little wired why its slowing down when you add another device, it's suppose to be additional.

So i want to other methods here in the forum, with experiment peoples, and now you are connected, so it's my lucky day.

Thanks
member
Activity: 77
Merit: 10
Today, I am getting my second TP-Link MR3020 Router (obviously, I bricked the first one Roll Eyes ).

To prevent bricking the device again, what are the steps that have to be taken?

Code:

1. Connect router to PC and connect with IP 192.168.0.254
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release)
3. connect tp-link router to my homenetwork router( IP range is 192.168.0.0 - 255)
4. Connect to tp-link via 192.168.0.99 and set a userpassword. Save and Apply.
5. Set all parameters in cgminer window which are necessary. Save and Apply
6. Connect Hex16a2 boards with powerd usb hub to tp-link and start cgminer.
Is this right?

The reason I am asking is, because I can not really explain why my last router bricked, that's the reason for the dumb question Grin

Thanks in advance!

1. It's the best to set you PC ip to static ip like 192.168.0.50
2. open web browser & type 192.168.0.254
3. flash the router with new 0.1.5 factory image
4. wait until the router restart( LED off & on again)
5. do not move your router yet
6. open web browser & type 192.168.0.99
7. Set password, time
8. setting the ip as you desire
9. Set cgminer


I see that your point number 3 is dangerous. You don't need to do that yet.
On your point number 6, cgminer is auto start. So if all cgminer & network setting ok then cgminer will start even if there is no miner connected.

why is point 3 dangerous? I need to get Internet from somewhere  Grin

As I tried to set my desired ip, the router "bricked" or whatever
hero member
Activity: 728
Merit: 500
After the 3 day in town delivery UPS finally get you Wink
May I can try helping
legendary
Activity: 1610
Merit: 1000
Hello Zich,

Can i ask you for help, i'm really lost. Huh
I just got my miners yesterday, and i'm suffering a lot to make them working.
Thanks
Bestalg
A word for the public? What issues do you heve exactly? Zich is very knowledgable person and is online most of the times but just in case Wink
newbie
Activity: 49
Merit: 0
Hello Zich,

Can i ask you for help, i'm really lost. Huh
I just got my miners yesterday, and i'm suffering a lot to make them working.
Thanks
Bestalg
legendary
Activity: 1190
Merit: 1000
Today, I am getting my second TP-Link MR3020 Router (obviously, I bricked the first one Roll Eyes ).

To prevent bricking the device again, what are the steps that have to be taken?

Code:

1. Connect router to PC and connect with IP 192.168.0.254
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release)
3. connect tp-link router to my homenetwork router( IP range is 192.168.0.0 - 255)
4. Connect to tp-link via 192.168.0.99 and set a userpassword. Save and Apply.
5. Set all parameters in cgminer window which are necessary. Save and Apply
6. Connect Hex16a2 boards with powerd usb hub to tp-link and start cgminer.
Is this right?

The reason I am asking is, because I can not really explain why my last router bricked, that's the reason for the dumb question Grin

Thanks in advance!

1. It's the best to set you PC ip to static ip like 192.168.0.50
2. open web browser & type 192.168.0.254
3. flash the router with new 0.1.5 factory image
4. wait until the router restart( LED off & on again)
5. do not move your router yet
6. open web browser & type 192.168.0.99
7. Set password, time
8. setting the ip as you desire
9. Set cgminer


I see that your point number 3 is dangerous. You don't need to do that yet.
On your point number 6, cgminer is auto start. So if all cgminer & network setting ok then cgminer will start even if there is no miner connected.
legendary
Activity: 1610
Merit: 1000
Today, I am getting my second TP-Link MR3020 Router (obviously, I bricked the first one Roll Eyes ).

To prevent bricking the device again, what are the steps that have to be taken?

Code:

1. Connect router to PC and connect with IP 192.168.0.254
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release)
3. connect tp-link router to my homenetwork router( IP range is 192.168.0.0 - 255)
4. Connect to tp-link via 192.168.0.99 and set a userpassword. Save and Apply.
5. Set all parameters in cgminer window which are necessary. Save and Apply
6. Connect Hex16a2 boards with powerd usb hub to tp-link and start cgminer.
Is this right?

The reason I am asking is, because I can not really explain why my last router bricked, that's the reason for the dumb question Grin

Thanks in advance!
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release) - use *.factory.bin + wait - ping 192.168.0.254 -t when it stops to respond look at it to see it is rebooting

You can try fail http://wiki.openwrt.org/doc/howto/generic.failsafe

The big button tigers it it was wps if i remember correctly
 
if you reach point 4 it is less likley to brick it. The critical is 3 to 4



I don't know the filename yet form technobit, but why should I use factory image?
Already tried getting into failsafe mode over 2 days with my last router, no chance at all, so I wanna get this right now Smiley
Factory is used when flashing from vendor FW to openwrt. I think factory has bootloader inside also - it is much more bigger compared to sysupgrade one. I have not tested what will hapen if you use ssyupgrade from stock FW. Later on assuming you have openwrt already use sysupgrade image to upgrade to latest version. Always take a look into change log in case you are lasy like me go to web of cgminer and fill defaults for new boards if there are any (CoinCraft A1 is coming..), otherwise cgminer is not starting Wink
member
Activity: 77
Merit: 10
Today, I am getting my second TP-Link MR3020 Router (obviously, I bricked the first one Roll Eyes ).

To prevent bricking the device again, what are the steps that have to be taken?

Code:

1. Connect router to PC and connect with IP 192.168.0.254
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release)
3. connect tp-link router to my homenetwork router( IP range is 192.168.0.0 - 255)
4. Connect to tp-link via 192.168.0.99 and set a userpassword. Save and Apply.
5. Set all parameters in cgminer window which are necessary. Save and Apply
6. Connect Hex16a2 boards with powerd usb hub to tp-link and start cgminer.
Is this right?

The reason I am asking is, because I can not really explain why my last router bricked, that's the reason for the dumb question Grin

Thanks in advance!
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release) - use *.factory.bin + wait - ping 192.168.0.254 -t when it stops to respond look at it to see it is rebooting

You can try fail http://wiki.openwrt.org/doc/howto/generic.failsafe

The big button tigers it it was wps if i remember correctly
 
if you reach point 4 it is less likley to brick it. The critical is 3 to 4



I don't know the filename yet form technobit, but why should I use factory image?
Already tried getting into failsafe mode over 2 days with my last router, no chance at all, so I wanna get this right now Smiley
hero member
Activity: 490
Merit: 500
Today, I am getting my second TP-Link MR3020 Router (obviously, I bricked the first one Roll Eyes ).

To prevent bricking the device again, what are the steps that have to be taken?

Code:

1. Connect router to PC and connect with IP 192.168.0.254
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release)
3. connect tp-link router to my homenetwork router( IP range is 192.168.0.0 - 255)
4. Connect to tp-link via 192.168.0.99 and set a userpassword. Save and Apply.
5. Set all parameters in cgminer window which are necessary. Save and Apply
6. Connect Hex16a2 boards with powerd usb hub to tp-link and start cgminer.
Is this right?

The reason I am asking is, because I can not really explain why my last router bricked, that's the reason for the dumb question Grin

Thanks in advance!

I couldn't connect to mine after flashing, some things you should note.
Wifi is dissabled to save memory in the latest firmware so you got to connect it to your PC/Laptop with the Cat5UTP network cable.
I then had to turn DHCP off and manually set the IP in my laptop/pc to be on the same subnet before I could see it.
The only way to brick it really is to turn it off while it's in the middle of installing the new firmware.
legendary
Activity: 1610
Merit: 1000
Today, I am getting my second TP-Link MR3020 Router (obviously, I bricked the first one Roll Eyes ).

To prevent bricking the device again, what are the steps that have to be taken?

Code:

1. Connect router to PC and connect with IP 192.168.0.254
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release)
3. connect tp-link router to my homenetwork router( IP range is 192.168.0.0 - 255)
4. Connect to tp-link via 192.168.0.99 and set a userpassword. Save and Apply.
5. Set all parameters in cgminer window which are necessary. Save and Apply
6. Connect Hex16a2 boards with powerd usb hub to tp-link and start cgminer.
Is this right?

The reason I am asking is, because I can not really explain why my last router bricked, that's the reason for the dumb question Grin

Thanks in advance!
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release) - use *.factory.bin + wait - ping 192.168.0.254 -t when it stops to respond look at it to see it is rebooting

You can try fail http://wiki.openwrt.org/doc/howto/generic.failsafe

The big button tigers it it was wps if i remember correctly
 
if you reach point 4 it is less likley to brick it. The critical is 3 to 4

member
Activity: 77
Merit: 10
Today, I am getting my second TP-Link MR3020 Router (obviously, I bricked the first one Roll Eyes ).

To prevent bricking the device again, what are the steps that have to be taken?

Code:

1. Connect router to PC and connect with IP 192.168.0.254
2. Flash router with openwrt+ cgminer from technobit website( 0.1.5 release)
3. connect tp-link router to my homenetwork router( IP range is 192.168.0.0 - 255)
4. Connect to tp-link via 192.168.0.99 and set a userpassword. Save and Apply.
5. Set all parameters in cgminer window which are necessary. Save and Apply
6. Connect Hex16a2 boards with powerd usb hub to tp-link and start cgminer.
Is this right?

The reason I am asking is, because I can not really explain why my last router bricked, that's the reason for the dumb question Grin

Thanks in advance!
legendary
Activity: 1610
Merit: 1000
Hi Mudge,

Get you mh/s up to 1500 and your voltage up to 1.150v. mine with those settings is running at 21gh.

Anyone knows if its ok to go higher? I would like to get up to 24gh
Give the board some time at 1.1 1500 with tplink my is 23gh+. 24 is a bit high I think
full member
Activity: 125
Merit: 100
Hi Mudge,

Get you mh/s up to 1500 and your voltage up to 1.150v. mine with those settings is running at 21gh.

Anyone knows if its ok to go higher? I would like to get up to 24gh
Pages:
Jump to: