What intensity you're use for v7?
86/8/2 
Topic: SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching - page 205. (Read 237263 times)
July 05, 2018, 07:04:50 AM
July 05, 2018, 06:59:41 AM
Livada,
can you show 24 hours average, or hash count since start of the miner?
dingdongtobias,
thanks for the link, I will update them over there. I did not pay attention to CAST so much, as I never liked that miner and moved immediately away, so i have 0 screenshots, proofs or research.
can you show 24 hours average, or hash count since start of the miner?
dingdongtobias,
thanks for the link, I will update them over there. I did not pay attention to CAST so much, as I never liked that miner and moved immediately away, so i have 0 screenshots, proofs or research.
i can't find any of your screenshots for srb neither, probably because there aren't any.
Here is my screenshot 24h average on nanopool :
https://bitcointalksearch.org/topic/m.40640415
Also I did a 6 hour test for Xmr Stak you said it shows you the exact same hashrate like the pool side, but not in my case :
https://bitcointalksearch.org/topic/m.41077478
JCE I did not test yet, but i will give it a try.
Also DragonMike, where are your screenshots? Are you even using srbminer ?
Just ran SRBMiner 1.6.0 on one of my 7x RX 570 rigs for 24 hours on Nanopool. Mining XMR (normalv7).
Average hashrate on the pool was less than 1% lower than reported hashrate from the miner.
@Doktor83: apologies for asking you to answer for non-existing issues. Constantly having to look for more profitability in these difficult times makes me tired, obviously!
But on this noob topic all have SS if say any. only you dont have any but you proo with 7 rig WOW. Go be angry in other topic NOOB.
i test and i have best result in miner and pool with srb miner. You have beter with CAST? go use cast and leave this topic and All happy ..
my rig 1 have 4 vege and 6000HR in heavy
my rig 2 have 6 vega and 8900HR i nhevy
after 5-6 hour i se AL OK. pool give 250coin in 24 hour (10 per hour)
after 5 hour pool give 58coin. This is beter- ok mybe HR go down i n6 hour i dont now but HR go up and go down but this is it.
mybe you see problem in 1% but i dont see problem in 1%. i see 6000+HR in srbminer and i see 5600HR with cast. and this is problem with cast or stack. you have better miner? nice . i dont i have srbminer.
https://image.prntscr.com/image/O6EyXgQHQ0_LOK6Ek9_16w.jpg
July 05, 2018, 05:46:20 AM
Quote
nothing. black comand line window appears on start and exits immediately
can you post your .bat file?
setx GPU_FORCE_64BIT_PTR 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_MAX_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_MAX_SINGLE_ALLOC_PERCENT 100
@echo off
cd %~dp0
cls
set EXE=SRBMiner-CN.exe
%EXE% --config config.txt --pools pools.txt --logfile log.txt
"pause"
try remove double quote on pause command, so you will see what is the error message.
should be like below :
setx GPU_FORCE_64BIT_PTR 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_MAX_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_MAX_SINGLE_ALLOC_PERCENT 100
@echo off
cd %~dp0
cls
set EXE=SRBMiner-CN.exe
%EXE% --config config.txt --pools pools.txt --logfile log.txt
pause
okay, that worked. error in pools.txt
here it is, but whats wrong with it?
{
"pools" :
[
{"pool" : "ryo.miner.rocks:5555", "wallet" : "RYoLsg1HBKJV8P1hdmeR24ZY2sghUR8NJ5afEavWKt4mDuZiPKKMUn3FMj9HZM4ywWHJxUTs6U3QQGb CatrshKd8VUUcT8ftfUa", "password" : "w=radiki1"},
]
}
July 05, 2018, 05:45:26 AM
Can anyone say - what best intensity for CN-v7 on 1.6.2. for 580 8Gb cards?
July 05, 2018, 05:38:16 AM
Quote
nothing. black comand line window appears on start and exits immediately
can you post your .bat file?
setx GPU_FORCE_64BIT_PTR 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_MAX_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_MAX_SINGLE_ALLOC_PERCENT 100
@echo off
cd %~dp0
cls
set EXE=SRBMiner-CN.exe
%EXE% --config config.txt --pools pools.txt --logfile log.txt
"pause"
try remove double quote on pause command, so you will see what is the error message.
should be like below :
setx GPU_FORCE_64BIT_PTR 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_MAX_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_MAX_SINGLE_ALLOC_PERCENT 100
@echo off
cd %~dp0
cls
set EXE=SRBMiner-CN.exe
%EXE% --config config.txt --pools pools.txt --logfile log.txt
pause
July 05, 2018, 05:33:41 AM
Quote
nothing. black comand line window appears on start and exits immediately
can you post your .bat file?
setx GPU_FORCE_64BIT_PTR 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_MAX_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_MAX_SINGLE_ALLOC_PERCENT 100
@echo off
cd %~dp0
cls
set EXE=SRBMiner-CN.exe
%EXE% --config config.txt --pools pools.txt --logfile log.txt
"pause"
July 05, 2018, 05:32:40 AM
What intensity you're use for v7?
July 05, 2018, 05:30:09 AM
Quote
nothing. black comand line window appears on start and exits immediately
can you post your .bat file?
July 05, 2018, 05:29:25 AM
Livada,
can you show 24 hours average, or hash count since start of the miner?
dingdongtobias,
thanks for the link, I will update them over there. I did not pay attention to CAST so much, as I never liked that miner and moved immediately away, so i have 0 screenshots, proofs or research.
can you show 24 hours average, or hash count since start of the miner?
dingdongtobias,
thanks for the link, I will update them over there. I did not pay attention to CAST so much, as I never liked that miner and moved immediately away, so i have 0 screenshots, proofs or research.
i can't find any of your screenshots for srb neither, probably because there aren't any.
Here is my screenshot 24h average on nanopool :
https://bitcointalksearch.org/topic/m.40640415
Also I did a 6 hour test for Xmr Stak you said it shows you the exact same hashrate like the pool side, but not in my case :
https://bitcointalksearch.org/topic/m.41077478
JCE I did not test yet, but i will give it a try.
Also DragonMike, where are your screenshots? Are you even using srbminer ?
Just ran SRBMiner 1.6.0 on one of my 7x RX 570 rigs for 24 hours on Nanopool. Mining XMR (normalv7).
Average hashrate on the pool was less than 1% lower than reported hashrate from the miner.
@Doktor83: apologies for asking you to answer for non-existing issues. Constantly having to look for more profitability in these difficult times makes me tired, obviously!
July 05, 2018, 05:27:49 AM
Same rig, same driver, same everything except miner version?
Yes.why the miner just won't start with ryo coin?? it exits just on start
Add command "pause" in the end of .bat file and you will see some messages.nothing. black comand line window appears on start and exits immediately
July 05, 2018, 05:21:18 AM
with 1.6.0 - 8400
with 1.6.2 - 8800
Tell me pls Docta, why RX580-8gb have 1100h/s with old blockchain drivers, and 800h/s with 18.5.x in same system?
with 1.6.2 - 8800
Tell me pls Docta, why RX580-8gb have 1100h/s with old blockchain drivers, and 800h/s with 18.5.x in same system?
did you already set compute mode?
July 05, 2018, 04:15:14 AM
Same rig, same driver, same everything except miner version?
Yes.why the miner just won't start with ryo coin?? it exits just on start
Add command "pause" in the end of .bat file and you will see some messages. July 05, 2018, 03:45:30 AM
why the miner just won't start with ryo coin?? it exits just on start
July 05, 2018, 03:34:39 AM
with 1.6.0 - 8400
with 1.6.2 - 8800
Tell me pls Docta, why RX580-8gb have 1100h/s with old blockchain drivers, and 800h/s with 18.5.x in same system?
with 1.6.2 - 8800
Tell me pls Docta, why RX580-8gb have 1100h/s with old blockchain drivers, and 800h/s with 18.5.x in same system?
July 05, 2018, 03:17:44 AM
guys what is your 30 min average speed in statistics 1.6.0 vs 1.6.2?
1080 vs 1024Strange, really. I have 580 8g (hynix) cards i tested the miner on , and i get the same hashrate on V7 as on previous versions.
There are always HR fluctuations, and always will be, that's why i ask for the 30 min average, and not the value you get when pressing 'h'.
Same rig, same driver, same everything except miner version?
I will check to see if any of the changes i made could cause this HR drop.
July 05, 2018, 02:49:59 AM
Hello, does not display the temperature and speed of the fan. Video cards R9 370 series ...
Try to change adl_type parameter, default is 1, try 2.
Put it on "gpu_conf" to get something like that (for intensity, worksize e threads use your stable config, this is only for example):
"gpu_conf" :
[
{ "id" : 0, "intensity" : 50, "worksize" : 4, "threads" : 1, "adl_type": 2},
]
"adl_type" : 1 or 2 , 1 - USE OVERDRIVEN , 2 - USE OVERDRIVE 5. Default is 1 if not set. Option 2 (Overdrive 5) is suitable for older cards
Thank you so much bro!!!
July 05, 2018, 02:35:50 AM
Good afternoon, doctor. I have a 13-card rig.
1) 9 cards of Sapphire RX550 / 2Gb on baffin
2) 1 card of Sapphire RX550 / 2 Gb on gfx804
3) 3 cards of MSI AERO RX550 / 2 GB on gfx804
On version 1.6.0, all cards worked with parameters 26.3 / 12 and issued:
1) at 497 h/s
2) 498 h/s
3) at 513 h/s
to my great regret at the transition to 1.6.1, and now on 1.6.2 with the same parameters of the cards began to give different results. In particular
The cards from point (1) remained at the same values, and from point (2) and (3) began to jump from 410 to 480 h/s. By reducing the parameters to 22.1/12 I was able to achieve a stable speed on the MSI cards from (3) of 499 h/s, but could not achieve an acceptable speed on the card from point (2). I went through all the intensity options from 18 to 28 in steps of 0.1 the maximum stable result was reached at 22.1 / 12 at 475 h/s.
1) 9 cards of Sapphire RX550 / 2Gb on baffin
2) 1 card of Sapphire RX550 / 2 Gb on gfx804
3) 3 cards of MSI AERO RX550 / 2 GB on gfx804
On version 1.6.0, all cards worked with parameters 26.3 / 12 and issued:
1) at 497 h/s
2) 498 h/s
3) at 513 h/s
to my great regret at the transition to 1.6.1, and now on 1.6.2 with the same parameters of the cards began to give different results. In particular
The cards from point (1) remained at the same values, and from point (2) and (3) began to jump from 410 to 480 h/s. By reducing the parameters to 22.1/12 I was able to achieve a stable speed on the MSI cards from (3) of 499 h/s, but could not achieve an acceptable speed on the card from point (2). I went through all the intensity options from 18 to 28 in steps of 0.1 the maximum stable result was reached at 22.1 / 12 at 475 h/s.
July 05, 2018, 02:33:47 AM
guys what is your 30 min average speed in statistics 1.6.0 vs 1.6.2?
1080 vs 1024 July 05, 2018, 02:32:21 AM
In 1.6.2 on cn-v7 algo intensity higher 100 not give jumps and drops in hashrate like it was on 1.6.1. But speed is low on v7... I tried 54,56,72,90,108,116 but all these intensities gives max 985 h/s on my RX 580 8Gb cards. On 1.6.0 I have 1030-1040 h/s...
Maybe I do something wrong? I tried to wait up to 10 min every try. But speed didn't jumps like in heavy algo. It pretty stable. Couse of it I didn't wait any longer.
Who got speed higher 1000 h/s on v7 with 1.6.2? Share your settings, please...
Maybe I do something wrong? I tried to wait up to 10 min every try. But speed didn't jumps like in heavy algo. It pretty stable. Couse of it I didn't wait any longer.
Who got speed higher 1000 h/s on v7 with 1.6.2? Share your settings, please...
Same issue: 1.6.0 gets 1080 h/s on RX 588, but 1.6.2 - only 1025 h/s with same config.
guys what is your 30 min average speed in statistics 1.6.0 vs 1.6.2?
It's not my questions. But on srb 1.6.1- 1.6.2 i see lower performance about 50 h/s on one rx550 card. If need i can publish logs.
On the same configs. Perhaps we need to change configuration, intensity or worksize?
July 04, 2018, 11:39:58 PM
In 1.6.2 on cn-v7 algo intensity higher 100 not give jumps and drops in hashrate like it was on 1.6.1. But speed is low on v7... I tried 54,56,72,90,108,116 but all these intensities gives max 985 h/s on my RX 580 8Gb cards. On 1.6.0 I have 1030-1040 h/s...
Maybe I do something wrong? I tried to wait up to 10 min every try. But speed didn't jumps like in heavy algo. It pretty stable. Couse of it I didn't wait any longer.
Who got speed higher 1000 h/s on v7 with 1.6.2? Share your settings, please...
Maybe I do something wrong? I tried to wait up to 10 min every try. But speed didn't jumps like in heavy algo. It pretty stable. Couse of it I didn't wait any longer.
Who got speed higher 1000 h/s on v7 with 1.6.2? Share your settings, please...
Same issue: 1.6.0 gets 1080 h/s on RX 588, but 1.6.2 - only 1025 h/s with same config.
guys what is your 30 min average speed in statistics 1.6.0 vs 1.6.2?
Jump to: