Topic: [UPDATE] RX480 (Ref) 31+Mh, Custom Rom - VDDC OFFSET + Custom timing - page 15. (Read 231045 times)
November 01, 2016, 04:17:26 PM
I only get 24 sol/s with stock bios i see some ppl reporting 30 Sol/s or higher with rx 480 i assume because of modded memory straps.
November 01, 2016, 12:08:08 PM
http://i1294.photobucket.com/albums/b608/mercurymatt/msirx480_zpsbeqmjtpy.jpg
Anyone know why the gpu voltages are not in actual mV? Is it safe to just enter a value in mV? This is Mis rx 480 4gb btw, thanks!
Anyone know why the gpu voltages are not in actual mV? Is it safe to just enter a value in mV? This is Mis rx 480 4gb btw, thanks!
You can enter mV values but they will be ignored. GPU core voltage is calculated at runtime in relative steps to its base voltage. What you will need is an offset either hardcoded into the bios using a hex editor ( complicated ) or a tool like Strixx or Watttool ( simple ) to load the core voltage offset at system startup.
I have just started using watttool to adjust voltages, in regards to the memory i should copy the timings from 1750 strap across to the 2000mhz strap and flash that?
That is right. That is what most people do. But for the ZCash mining, it is better to use the stock bios.
November 01, 2016, 06:31:17 AM
Anyone know why the gpu voltages are not in actual mV? Is it safe to just enter a value in mV? This is Mis rx 480 4gb btw, thanks!
You can enter mV values but they will be ignored. GPU core voltage is calculated at runtime in relative steps to its base voltage. What you will need is an offset either hardcoded into the bios using a hex editor ( complicated ) or a tool like Strixx or Watttool ( simple ) to load the core voltage offset at system startup.
I have just started using watttool to adjust voltages, in regards to the memory i should copy the timings from 1750 strap across to the 2000mhz strap and flash that?
October 31, 2016, 09:58:11 PM
Nice work 
Thanks October 31, 2016, 04:48:23 PM
Radeon RX 480 Sapphire Nitro+ OC PCI-E 8192Mb (11260-01-20G)
PCI-E 3.0, ядpo - 1208 MГц, Boost - 1342 MГц, пaмять - 8192 Mб GDDR5 8000 MГц, 256 бит, DVI, 2xHDMI, 2xDisplayPort, Retail
Radeon RX 480 Sapphire Nitro+ PCI-E 8192Mb (11260-07-20G)
PCI-E 3.0, ядpo - 1208 MГц, Boost - 1306 MГц, пaмять - 8192 Mб GDDR5 8000 MГц, 256 бит, DVI, 2xHDMI, 2xDisplayPort, Retail
which is better?
PCI-E 3.0, ядpo - 1208 MГц, Boost - 1342 MГц, пaмять - 8192 Mб GDDR5 8000 MГц, 256 бит, DVI, 2xHDMI, 2xDisplayPort, Retail
Radeon RX 480 Sapphire Nitro+ PCI-E 8192Mb (11260-07-20G)
PCI-E 3.0, ядpo - 1208 MГц, Boost - 1306 MГц, пaмять - 8192 Mб GDDR5 8000 MГц, 256 бит, DVI, 2xHDMI, 2xDisplayPort, Retail
which is better?
For mining you'll find they're identical with identically modified BIOS. Get whichever is cheapest IMO.
October 31, 2016, 04:26:52 PM
Radeon RX 480 Sapphire Nitro+ OC PCI-E 8192Mb (11260-01-20G)
PCI-E 3.0, ядpo - 1208 MГц, Boost - 1342 MГц, пaмять - 8192 Mб GDDR5 8000 MГц, 256 бит, DVI, 2xHDMI, 2xDisplayPort, Retail
Radeon RX 480 Sapphire Nitro+ PCI-E 8192Mb (11260-07-20G)
PCI-E 3.0, ядpo - 1208 MГц, Boost - 1306 MГц, пaмять - 8192 Mб GDDR5 8000 MГц, 256 бит, DVI, 2xHDMI, 2xDisplayPort, Retail
which is better?
PCI-E 3.0, ядpo - 1208 MГц, Boost - 1342 MГц, пaмять - 8192 Mб GDDR5 8000 MГц, 256 бит, DVI, 2xHDMI, 2xDisplayPort, Retail
Radeon RX 480 Sapphire Nitro+ PCI-E 8192Mb (11260-07-20G)
PCI-E 3.0, ядpo - 1208 MГц, Boost - 1306 MГц, пaмять - 8192 Mб GDDR5 8000 MГц, 256 бит, DVI, 2xHDMI, 2xDisplayPort, Retail
which is better?
October 31, 2016, 02:31:00 PM
Anyone know why the gpu voltages are not in actual mV? Is it safe to just enter a value in mV? This is Mis rx 480 4gb btw, thanks!
You can enter mV values but they will be ignored. GPU core voltage is calculated at runtime in relative steps to its base voltage. What you will need is an offset either hardcoded into the bios using a hex editor ( complicated ) or a tool like Strixx or Watttool ( simple ) to load the core voltage offset at system startup.
October 31, 2016, 02:28:59 PM
Anyone know why the gpu voltages are not in actual mV? Is it safe to just enter a value in mV? This is Mis rx 480 4gb btw, thanks!
Yes, you can put voltages...
You know that's not possible. Its probably just the first half of the Straps that are the same/similar.
October 31, 2016, 04:42:47 AM
Hello.
I have Sapphire RX 480 Nitro+ 8G, default 1342 MHz / 1150 mV maximum.
I changed DPM table in PBE at -75mV. After flashing bios, voltage settings was default (stock, not changed). Why?
The new settings was applied only after pressing Reset button in MSI Afterburner or Trixx.
Then if I play with voltage in Trixx, card may be crashed. And after rebooting voltage is default (stock) again!! Why?? What should I do to voltage were always the ones that I setup in DPM?
I have Sapphire RX 480 Nitro+ 8G, default 1342 MHz / 1150 mV maximum.
I changed DPM table in PBE at -75mV. After flashing bios, voltage settings was default (stock, not changed). Why?
The new settings was applied only after pressing Reset button in MSI Afterburner or Trixx.
Then if I play with voltage in Trixx, card may be crashed. And after rebooting voltage is default (stock) again!! Why?? What should I do to voltage were always the ones that I setup in DPM?
October 30, 2016, 08:35:06 PM
Anyone know why the gpu voltages are not in actual mV? Is it safe to just enter a value in mV? This is Mis rx 480 4gb btw, thanks!
Yes, you can put voltages...
October 30, 2016, 05:26:19 PM
Anyone know why the gpu voltages are not in actual mV? Is it safe to just enter a value in mV? This is Mis rx 480 4gb btw, thanks!
October 29, 2016, 02:12:29 PM
is there any modded bios for 470 oc 4 gb?
October 29, 2016, 10:16:04 AM
i just wanted to ask, is there a reason the final 33Mh/s rom from Heliox was not released and the other posted roms in the 1st page are down? 
awesome job btw!
awesome job btw!
October 29, 2016, 09:36:46 AM
ok, problem solved
now PLEASE some one... link to a rom for 27-28mhs+ for sapphire nitro+ OC 4GB
Thank you
now PLEASE some one... link to a rom for 27-28mhs+ for sapphire nitro+ OC 4GB
Thank you
October 29, 2016, 07:18:17 AM
i have rx480 sapphire nitro+ oc 4gb
and the same card with 8gb
bios of 4gb... in the polaris editor, i have 3 options in VRAM menu
bios of 8gb card, has only 1
?
and the same card with 8gb
bios of 4gb... in the polaris editor, i have 3 options in VRAM menu
bios of 8gb card, has only 1
? October 29, 2016, 07:01:16 AM
great job
October 29, 2016, 06:24:07 AM
why... if change anything in polaris bios and update bios on my sapphire 4gb, it not working, no picture nothing?
even if change only 1mhz in the memmory.
even if manualy put back on stock settings, not working, i must flash with stock (backup) file/bios...
why???
Update
i open original (backup file) in polaris editor 1.4
just open and save... flash saved bios... not working
like, polaris bios "destroj" the file.
what is going on?
even if change only 1mhz in the memmory.
even if manualy put back on stock settings, not working, i must flash with stock (backup) file/bios...
why???
Update
i open original (backup file) in polaris editor 1.4
just open and save... flash saved bios... not working
like, polaris bios "destroj" the file.
what is going on?
October 29, 2016, 05:49:48 AM
please, any settings for polaris bios editor, for sapphire nitro+ oc 4gb??
October 28, 2016, 11:26:54 AM
it is possible to get some link, for bios for, sapphire nitro+ oc 4Gb for 30-+mhs ?
Please.
Please.
elpida?
If you find the right memory strap for your elpida, it is possible to get that GPU to have 30+ MH/s rate.
October 28, 2016, 10:26:42 AM
it is possible to get some link, for bios for, sapphire nitro+ oc 4Gb for 30-+mhs ?
Please.
Please.
elpida?
Jump to: