ZTEX USB-FPGA Modules 1.15x and 1.15y: 215 and 860 MH/s FPGA Boards - page 8.

ocminer

legendary

Activity: 2688

Merit: 1240

Quote from: ztex on October 18, 2012, 03:31:22 AM

Quote from: Turbor on October 17, 2012, 02:02:08 PM

The test version runs fine here. Any plans for new products in the ASIC direction ?

Virtual or real ASIC's?

Virtual ASIC's are developed on request. Just write me how much MH/s you want and I will send you an invoice. ;-)

Real ASIC's are more complex. Such large devices are everything but trivial and it is quite likely that more than one attempt is required.

I consider it as too risky (and I strongly recommend not to invest money into ASIC products until a working prototype has been seen.)

I will not discuss this topic further.

+1

ztex

donator

Activity: 367

Merit: 250

ZTEX FPGA Boards

Quote from: ummas on October 17, 2012, 02:39:29 PM

Thx for the hint ztex.
Today i`ll put a sticker on every board with a serial.
But still, there could be notyfication at the end of the cluster information, that "XXXXX" is overheating/missing.
It`s hard to hunt with 68 miners, and i`ll try to make it even harder.

Serial number feature is the ability to give the boards an individual and more handy number than the MAC adress which is used as default, see http://www.ztex.de/btcminer, topic "Running a FPGA cluster".

If a fatal error occurs the miner is not removed from the status message list. Instead of the statistics you see "... Error: ... device disabled since ...". After a rescan these devices are removed from the status list.

ztex

donator

Activity: 367

Merit: 250

ZTEX FPGA Boards

Quote from: Turbor on October 17, 2012, 02:02:08 PM

The test version runs fine here. Any plans for new products in the ASIC direction ?

Virtual or real ASIC's?

Virtual ASIC's are developed on request. Just write me how much MH/s you want and I will send you an invoice. ;-)

Real ASIC's are more complex. Such large devices are everything but trivial and it is quite likely that more than one attempt is required.

I consider it as too risky (and I strongly recommend not to invest money into ASIC products until a working prototype has been seen.)

I will not discuss this topic further.

ummas

sr. member

Activity: 274

Merit: 250

Thx for the hint ztex.
Today i`ll put a sticker on every board with a serial.
But still, there could be notyfication at the end of the cluster information, that "XXXXX" is overheating/missing.
It`s hard to hunt with 68 miners, and i`ll try to make it even harder.

Turbor

legendary

Activity: 1022

Merit: 1000

BitMinter

The test version runs fine here. Any plans for new products in the ASIC direction ?

ztex

donator

Activity: 367

Merit: 250

ZTEX FPGA Boards

There where several news within the last weeks:

A new revision of USB-FPGA Modules 1.15y is shipped since end of September. The new FPGA Boards have on-board temperature sensors. Products page (http://www.ztex.de/usb-fpga-1/usb-fpga-1.15y.e.html) has just been updated.
A testing release of BTCMiner with support for these temperature sensors is available too, see https://bitcointalksearch.org/topic/m.1278453
Until Oct. 26 2012 there is an approximately 10% discount on USB-FPGA Modules 1.15y. Prices are
1-4 units: 899 EUR / 1205 USD
5-9 units: 809 EUR / 1079 USD
10-24 units: 729 EUR / 979 USD
25-49 units: 649 EUR / 869 USD
50-99 units: 629 EUR / 839 USD
100+ units: 609 EUR / 809 USD

ztex

donator

Activity: 367

Merit: 250

ZTEX FPGA Boards

Quote from: ummas on October 17, 2012, 07:34:09 AM

Any1 can help find that little non working chip??

Code:

(Re)Scanning bus ...
0 new devices found.

Summary:
  Bus 001-0 : 10 miners
  Bus 001-1 : 10 miners
  Bus 001-2 : 10 miners
  Bus 001-3 : 9 miners
  Bus 001-4 : 10 miners
  Bus 001-5 : 10 miners
  Bus 001-6 : 8 miners
  Total : 67 miners

If one FPGA disappears for some reason it is not found by a rescan unless the board is plugged off and on.

The troublemaker can be found by taking a look into the log (search for "error").

Or simply restart the cluster (you did not use the serial number feature for easy identification).

ummas

sr. member

Activity: 274

Merit: 250

Any1 can help find that little non working chip??

Code:

(Re)Scanning bus ...
0 new devices found.

Summary:
  Bus 001-0 : 10 miners
  Bus 001-1 : 10 miners
  Bus 001-2 : 10 miners
  Bus 001-3 : 9 miners
  Bus 001-4 : 10 miners
  Bus 001-5 : 10 miners
  Bus 001-6 : 8 miners
  Total : 67 miners

Code:

001-0: ztex_ufm1_15y1-04A3460F9A-1: f=228,00MHz, errorRate=0,55%, maxErrorRate=2,36%, hashRate=226,7MH/s, submitted 17 new nonces, luckFactor=0,97
001-0: ztex_ufm1_15y1-04A3460F9A-2: f=228,00MHz, errorRate=0,00%, maxErrorRate=0,64%, hashRate=228,0MH/s, submitted 20 new nonces, luckFactor=0,99
001-0: ztex_ufm1_15y1-04A3460F9A-3: f=228,00MHz, errorRate=0,01%, maxErrorRate=1,36%, hashRate=228,0MH/s, submitted 21 new nonces, luckFactor=1,00
001-0: ztex_ufm1_15y1-04A3460F9A-4: f=232,00MHz, errorRate=0,00%, maxErrorRate=1,18%, hashRate=232,0MH/s, submitted 13 new nonces, luckFactor=0,98
001-0: ztex_ufm1_15y1-04A3465805-1: f=216,00MHz, errorRate=0,00%, maxErrorRate=0,93%, hashRate=216,0MH/s, submitted 14 new nonces, luckFactor=0,97
001-0: ztex_ufm1_15y1-04A3465805-2: f=220,00MHz, errorRate=0,00%, maxErrorRate=1,90%, hashRate=220,0MH/s, submitted 19 new nonces, luckFactor=0,97
001-0: ztex_ufm1_15y1-04A3465805-3: f=232,00MHz, errorRate=0,00%, maxErrorRate=0,63%, hashRate=232,0MH/s, submitted 20 new nonces, luckFactor=0,98
001-0: ztex_ufm1_15y1-04A3465805-4: f=232,00MHz, errorRate=0,39%, maxErrorRate=2,34%, hashRate=231,1MH/s, submitted 18 new nonces, luckFactor=0,99
001-0: ztex_ufm1_15y1-04A39E3F35-1: f=228,00MHz, errorRate=0,37%, maxErrorRate=2,04%, hashRate=227,1MH/s, T=45,1°C, submitted 22 new nonces, luckFactor=1,02
001-0: ztex_ufm1_15y1-04A39E3FFF-2: f=224,00MHz, errorRate=0,00%, maxErrorRate=1,75%, hashRate=224,0MH/s, T=54,2°C, submitted 13 new nonces, luckFactor=0,96
001-1: ztex_ufm1_15y1-04A3460FB8-1: f=216,00MHz, errorRate=0,00%, maxErrorRate=0,99%, hashRate=216,0MH/s, submitted 18 new nonces, luckFactor=0,99
001-1: ztex_ufm1_15y1-04A3460FB8-2: f=220,00MHz, errorRate=0,00%, maxErrorRate=0,82%, hashRate=220,0MH/s, submitted 16 new nonces, luckFactor=0,99
001-1: ztex_ufm1_15y1-04A3460FB8-3: f=228,00MHz, errorRate=0,00%, maxErrorRate=0,80%, hashRate=228,0MH/s, submitted 20 new nonces, luckFactor=1,00
001-1: ztex_ufm1_15y1-04A3460FB8-4: f=220,00MHz, errorRate=0,02%, maxErrorRate=2,01%, hashRate=219,9MH/s, submitted 16 new nonces, luckFactor=1,00
001-1: ztex_ufm1_15y1-04A3467011-1: f=220,00MHz, errorRate=0,00%, maxErrorRate=0,66%, hashRate=220,0MH/s, submitted 12 new nonces, luckFactor=1,00
001-1: ztex_ufm1_15y1-04A3467011-2: f=212,00MHz, errorRate=0,27%, maxErrorRate=1,00%, hashRate=211,4MH/s, submitted 10 new nonces, luckFactor=0,99
001-1: ztex_ufm1_15y1-04A3467011-3: f=224,00MHz, errorRate=0,00%, maxErrorRate=1,02%, hashRate=224,0MH/s, submitted 13 new nonces, luckFactor=0,99
001-1: ztex_ufm1_15y1-04A3467011-4: f=228,00MHz, errorRate=0,01%, maxErrorRate=1,00%, hashRate=228,0MH/s, submitted 17 new nonces, luckFactor=1,00
001-1: ztex_ufm1_15y1-04A39E3FFF-3: f=220,00MHz, errorRate=0,00%, maxErrorRate=1,01%, hashRate=220,0MH/s, T=42,5°C, submitted 5 new nonces, luckFactor=1,00
001-1: ztex_ufm1_15y1-04A39E3FFF-4: f=228,00MHz, errorRate=0,02%, maxErrorRate=1,48%, hashRate=228,0MH/s, T=38,6°C, submitted 13 new nonces, luckFactor=0,97
001-2: ztex_ufm1_15y1-04A3467D4E-1: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,50%, hashRate=224,0MH/s, submitted 14 new nonces, luckFactor=1,00
001-2: ztex_ufm1_15y1-04A3467D4E-2: f=224,00MHz, errorRate=0,14%, maxErrorRate=2,45%, hashRate=223,7MH/s, submitted 14 new nonces, luckFactor=0,99
001-2: ztex_ufm1_15y1-04A3467D4E-3: f=220,00MHz, errorRate=0,00%, maxErrorRate=1,04%, hashRate=220,0MH/s, submitted 8 new nonces, luckFactor=0,97
001-2: ztex_ufm1_15y1-04A3467D4E-4: f=220,00MHz, errorRate=0,00%, maxErrorRate=1,09%, hashRate=220,0MH/s, submitted 18 new nonces, luckFactor=0,96
001-2: ztex_ufm1_15y1-04A3469808-1: f=208,00MHz, errorRate=0,00%, maxErrorRate=0,90%, hashRate=208,0MH/s, submitted 12 new nonces, luckFactor=0,98
001-2: ztex_ufm1_15y1-04A3469808-2: f=196,00MHz, errorRate=0,04%, maxErrorRate=1,49%, hashRate=195,9MH/s, submitted 17 new nonces, luckFactor=0,98
001-2: ztex_ufm1_15y1-04A3469808-3: f=196,00MHz, errorRate=0,37%, maxErrorRate=1,54%, hashRate=195,3MH/s, submitted 12 new nonces, luckFactor=1,00
001-2: ztex_ufm1_15y1-04A3469808-4: f=196,00MHz, errorRate=0,12%, maxErrorRate=1,92%, hashRate=195,8MH/s, submitted 12 new nonces, luckFactor=1,00
001-2: ztex_ufm1_15y1-04A39E6630-1: f=224,00MHz, errorRate=0,00%, maxErrorRate=1,29%, hashRate=224,0MH/s, T=42,5°C, submitted 17 new nonces, luckFactor=0,97
001-2: ztex_ufm1_15y1-04A39E6630-2: f=224,00MHz, errorRate=0,00%, maxErrorRate=1,45%, hashRate=224,0MH/s, T=50,9°C, submitted 8 new nonces, luckFactor=0,98
001-3: ztex_ufm1_15y1-04A39E2C9F-1: f=224,00MHz, errorRate=0,00%, maxErrorRate=1,00%, hashRate=224,0MH/s, T=47,7°C, submitted 18 new nonces, luckFactor=0,98
001-3: ztex_ufm1_15y1-04A39E2C9F-2: f=224,00MHz, errorRate=0,27%, maxErrorRate=1,19%, hashRate=223,4MH/s, T=50,9°C, submitted 12 new nonces, luckFactor=0,98
001-3: ztex_ufm1_15y1-04A39E2C9F-3: f=224,00MHz, errorRate=0,06%, maxErrorRate=1,04%, hashRate=223,9MH/s, T=45,1°C, submitted 17 new nonces, luckFactor=0,99
001-3: ztex_ufm1_15y1-04A39E2C9F-4: f=220,00MHz, errorRate=1,60%, maxErrorRate=1,94%, hashRate=216,5MH/s, T=42,5°C, submitted 19 new nonces, luckFactor=0,97
001-3: ztex_ufm1_15y1-04A39E3F35-2: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,77%, hashRate=224,0MH/s, T=43,8°C, submitted 19 new nonces, luckFactor=1,07
001-3: ztex_ufm1_15y1-04A39E3F35-3: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,64%, hashRate=224,0MH/s, T=42,5°C, submitted 20 new nonces, luckFactor=1,00
001-3: ztex_ufm1_15y1-04A39E3F35-4: f=216,00MHz, errorRate=0,00%, maxErrorRate=0,00%, hashRate=216,0MH/s, T=43,8°C, submitted 14 new nonces, luckFactor=1,06
001-3: ztex_ufm1_15y1-04A39E6630-3: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,97%, hashRate=224,0MH/s, T=42,5°C, submitted 8 new nonces, luckFactor=0,99
001-3: ztex_ufm1_15y1-04A39E6630-4: f=220,00MHz, errorRate=0,00%, maxErrorRate=0,50%, hashRate=220,0MH/s, T=41,9°C, submitted 15 new nonces, luckFactor=1,00
001-4: ztex_ufm1_15y1-04A39E41D7-1: f=232,00MHz, errorRate=0,00%, maxErrorRate=0,94%, hashRate=232,0MH/s, T=42,5°C, submitted 11 new nonces, luckFactor=0,99
001-4: ztex_ufm1_15y1-04A39E41D7-2: f=228,00MHz, errorRate=0,02%, maxErrorRate=1,80%, hashRate=228,0MH/s, T=45,1°C, submitted 9 new nonces, luckFactor=0,99
001-4: ztex_ufm1_15y1-04A39E41D7-3: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,95%, hashRate=224,0MH/s, T=42,5°C, submitted 15 new nonces, luckFactor=0,98
001-4: ztex_ufm1_15y1-04A39E41D7-4: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,50%, hashRate=224,0MH/s, T=42,5°C, submitted 17 new nonces, luckFactor=0,99
001-4: ztex_ufm1_15y1-04A39E7920-1: f=232,00MHz, errorRate=0,40%, maxErrorRate=1,46%, hashRate=231,1MH/s, T=45,1°C, submitted 7 new nonces, luckFactor=0,99
001-4: ztex_ufm1_15y1-04A39E7920-2: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,76%, hashRate=224,0MH/s, T=50,9°C, submitted 6 new nonces, luckFactor=1,02
001-4: ztex_ufm1_15y1-04A39E7920-3: f=232,00MHz, errorRate=0,06%, maxErrorRate=1,93%, hashRate=231,9MH/s, T=45,1°C, submitted 22 new nonces, luckFactor=0,98
001-4: ztex_ufm1_15y1-04A39E7920-4: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,98%, hashRate=224,0MH/s, T=45,1°C, submitted 18 new nonces, luckFactor=1,01
001-4: ztex_ufm1_15y1-04A39E7AB8-1: f=228,00MHz, errorRate=0,00%, maxErrorRate=0,80%, hashRate=228,0MH/s, T=41,9°C, submitted 16 new nonces, luckFactor=0,99
001-4: ztex_ufm1_15y1-04A39E7AB8-2: f=228,00MHz, errorRate=0,52%, maxErrorRate=2,15%, hashRate=226,8MH/s, T=45,1°C, submitted 15 new nonces, luckFactor=1,02
001-5: ztex_ufm1_15y1-04A39E5505-1: f=220,00MHz, errorRate=0,17%, maxErrorRate=1,41%, hashRate=219,6MH/s, T=50,9°C, submitted 12 new nonces, luckFactor=0,99
001-5: ztex_ufm1_15y1-04A39E5505-2: f=228,00MHz, errorRate=0,11%, maxErrorRate=1,95%, hashRate=227,8MH/s, T=52,9°C, submitted 10 new nonces, luckFactor=0,97
001-5: ztex_ufm1_15y1-04A39E5505-3: f=220,00MHz, errorRate=0,13%, maxErrorRate=1,72%, hashRate=219,7MH/s, T=49,0°C, submitted 13 new nonces, luckFactor=0,99
001-5: ztex_ufm1_15y1-04A39E5505-4: f=224,00MHz, errorRate=0,00%, maxErrorRate=1,00%, hashRate=224,0MH/s, T=50,9°C, submitted 13 new nonces, luckFactor=0,98
001-5: ztex_ufm1_15y1-04A39E78A1-1: f=228,00MHz, errorRate=0,00%, maxErrorRate=0,66%, hashRate=228,0MH/s, T=45,1°C, submitted 17 new nonces, luckFactor=0,99
001-5: ztex_ufm1_15y1-04A39E78A1-2: f=232,00MHz, errorRate=0,38%, maxErrorRate=1,25%, hashRate=231,1MH/s, T=49,0°C, submitted 16 new nonces, luckFactor=1,01
001-5: ztex_ufm1_15y1-04A39E78A1-3: f=224,00MHz, errorRate=0,01%, maxErrorRate=1,71%, hashRate=224,0MH/s, T=45,1°C, submitted 21 new nonces, luckFactor=1,00
001-5: ztex_ufm1_15y1-04A39E78A1-4: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,68%, hashRate=224,0MH/s, T=42,5°C, submitted 13 new nonces, luckFactor=0,98
001-5: ztex_ufm1_15y1-04A39E7AB8-3: f=228,00MHz, errorRate=0,00%, maxErrorRate=1,05%, hashRate=228,0MH/s, T=41,9°C, submitted 18 new nonces, luckFactor=0,98
001-5: ztex_ufm1_15y1-04A39E7AB8-4: f=224,00MHz, errorRate=0,00%, maxErrorRate=0,50%, hashRate=224,0MH/s, T=42,5°C, submitted 22 new nonces, luckFactor=1,00
001-6: ztex_ufm1_15y1-04A39E4067-1: f=228,00MHz, errorRate=0,00%, maxErrorRate=1,04%, hashRate=228,0MH/s, T=50,9°C, submitted 19 new nonces, luckFactor=0,98
001-6: ztex_ufm1_15y1-04A39E4067-2: f=224,00MHz, errorRate=0,01%, maxErrorRate=1,77%, hashRate=224,0MH/s, T=52,9°C, submitted 13 new nonces, luckFactor=0,97
001-6: ztex_ufm1_15y1-04A39E4067-3: f=224,00MHz, errorRate=0,00%, maxErrorRate=1,74%, hashRate=224,0MH/s, T=52,9°C, submitted 17 new nonces, luckFactor=0,98
001-6: ztex_ufm1_15y1-04A39E4067-4: f=224,00MHz, errorRate=0,57%, maxErrorRate=2,39%, hashRate=222,7MH/s, T=50,9°C, submitted 9 new nonces, luckFactor=1,00
001-6: ztex_ufm1_15y1-04A39E66B5-1: f=228,00MHz, errorRate=0,00%, maxErrorRate=0,50%, hashRate=228,0MH/s, T=48,4°C, submitted 23 new nonces, luckFactor=1,00
001-6: ztex_ufm1_15y1-04A39E66B5-2: f=228,00MHz, errorRate=0,00%, maxErrorRate=0,98%, hashRate=228,0MH/s, T=52,2°C, submitted 10 new nonces, luckFactor=0,99
001-6: ztex_ufm1_15y1-04A39E66B5-3: f=228,00MHz, errorRate=1,03%, maxErrorRate=2,31%, hashRate=225,6MH/s, T=45,1°C, submitted 18 new nonces, luckFactor=0,99
001-6: ztex_ufm1_15y1-04A39E66B5-4: f=224,00MHz, errorRate=0,00%, maxErrorRate=1,00%, hashRate=224,0MH/s, T=47,1°C, submitted 15 new nonces, luckFactor=0,99
001-0: poll loop time: 73ms (USB: 15ms network: 58ms) getwork time: 117ms submit time: 125ms
001-1: poll loop time: 72ms (USB: 15ms network: 58ms) getwork time: 123ms submit time: 126ms
001-2: poll loop time: 69ms (USB: 15ms network: 54ms) getwork time: 121ms submit time: 126ms
001-3: poll loop time: 66ms (USB: 13ms network: 52ms) getwork time: 124ms submit time: 130ms
001-4: poll loop time: 74ms (USB: 15ms network: 59ms) getwork time: 118ms submit time: 128ms
001-5: poll loop time: 74ms (USB: 15ms network: 59ms) getwork time: 120ms submit time: 128ms
001-6: poll loop time: 58ms (USB: 12ms network: 46ms) getwork time: 119ms submit time: 127ms
Total hash rate: 14934,8 MH/s
Total submitted hash rate: 14718,2 MH/s
--------

just one thoing comes on my mind, to switch off one after another and rescan after that and check witch one is it...
No leds tourned on as it was ussually.
Thx Ztex for REV 2 !

EDIT: is it possible to implement "BIG CLUSTERS" edition into it ? It`s really hard to find sommething under screen :/

ztex

donator

Activity: 367

Merit: 250

ZTEX FPGA Boards

Quote from: uuidman on October 03, 2012, 04:34:20 PM

I use a seasonix AX850, yup I havel also tried a different powersource, same results.

ATX supplies shouldn't cause this problems. Please send me an email (http://www.ztex.de/contact.e.html) so that I can give you the return address.

uuidman

full member

Activity: 121

Merit: 100

Quote from: Bogart on September 30, 2012, 02:49:23 PM

Quote from: uuidman on September 30, 2012, 02:10:15 PM

My fpgas has really been humming along nice. But now I got this:

ztex_ufm1_15y1-0000000016: Error configuring FPGA 2: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122)
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Retrying it ...
Warning: High speed FPGA configuration failed, trying low speed mode:Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Trying low speed mode
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122):

Im a little unsure, but before if they have been som problems uploading fw, the classic poweroff all pull usb-cables have allways worked and I had that error so few times so Im not sure if its the same errorcode.

I have made numerous restarts and changed cables and so on, I have also reprogrammed a couple of times and tried.
Anyone ?

How are you powering the board? Have you tried a different PS and/or power cable?

I use a seasonix AX850, yup I havel also tried a different powersource, same results.

Turbor

legendary

Activity: 1022

Merit: 1000

BitMinter

Quote from: enginehead on September 30, 2012, 06:17:22 PM

Help me please ztex. Huh

My 1.15x was working perfectly running stable at 212 mh when this happened.

user@computer-name:~$ sudo java -cp ZtexBTCMiner-120703.jar BTCMiner -host http://mmpool.bitparking.com:15098 -u xxx -p pass -b http://pool.50btc.com:8332 xxx pass -f ztex_ufm1_15d4.ihx -l log.txt -d 0 -v
ztex_ufm1_15d4-04A346E05B: New device: bitfile=ztex_ufm1_15d4 f_default=200.00MHz f_max=248.00MHz HpC=1.0H
ztex_ufm1_15d4-04A346E05B: MAC address: 0004a346e05b
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=222; 0 bytes got lost): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=222; 0 bytes got lost): Retrying it ...
Warning: High speed FPGA configuration failed, trying low speed mode:Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=222; 0 bytes got lost): Trying low speed mode

I've tried everything I can think of and have read on forums etc.

I get this error sometimes with my quad. Removing power and pluging it back in helps. No big problem.

After many months of usage the only problem with ztex products are this sort of errors. If running, they go for weeks or months but if you restart or turn them on and off they throw errors more frequent than a Icarus or BFL fpga.

ztex

donator

Activity: 367

Merit: 250

ZTEX FPGA Boards

Quote from: enginehead on September 30, 2012, 06:17:22 PM

Help me please ztex. Huh

My 1.15x was working perfectly running stable at 212 mh when this happened.

user@computer-name:~$ sudo java -cp ZtexBTCMiner-120703.jar BTCMiner -host http://mmpool.bitparking.com:15098 -u xxx -p pass -b http://pool.50btc.com:8332 xxx pass -f ztex_ufm1_15d4.ihx -l log.txt -d 0 -v
ztex_ufm1_15d4-04A346E05B: New device: bitfile=ztex_ufm1_15d4 f_default=200.00MHz f_max=248.00MHz HpC=1.0H
ztex_ufm1_15d4-04A346E05B: MAC address: 0004a346e05b
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=222; 0 bytes got lost): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=222; 0 bytes got lost): Retrying it ...
Warning: High speed FPGA configuration failed, trying low speed mode:Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=222; 0 bytes got lost): Trying low speed mode

I've tried everything I can think of and have read on forums etc.

enginehead, this is the third time you asked this question on Sunday within a few hours.

Why that aggressive flooding ? Because I did not answered immediately on Sunday !?

I sent you an email a few minutes ago. Answer is the same as above (https://bitcointalksearch.org/topic/m.1235527)

ztex

donator

Activity: 367

Merit: 250

ZTEX FPGA Boards

Quote from: uuidman on September 30, 2012, 02:10:15 PM

My fpgas has really been humming along nice. But now I got this:

ztex_ufm1_15y1-0000000016: Error configuring FPGA 2: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122)
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Retrying it ...
Warning: High speed FPGA configuration failed, trying low speed mode:Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Trying low speed mode
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122):

Im a little unsure, but before if they have been som problems uploading fw, the classic poweroff all pull usb-cables have allways worked and I had that error so few times so Im not sure if its the same errorcode.

I have made numerous restarts and changed cables and so on, I have also reprogrammed a couple of times and tried.
Anyone ?

It's either a power supply issue (also see https://bitcointalksearch.org/topic/m.1235512) or a defect.

If it's not the PSU please return the board for checking. I will give you the return address per email.

enginehead

newbie

Activity: 48

Merit: 0

Help me please ztex. Huh

My 1.15x was working perfectly running stable at 212 mh when this happened.

user@computer-name:~$ sudo java -cp ZtexBTCMiner-120703.jar BTCMiner -host http://mmpool.bitparking.com:15098 -u xxx -p pass -b http://pool.50btc.com:8332 xxx pass -f ztex_ufm1_15d4.ihx -l log.txt -d 0 -v
ztex_ufm1_15d4-04A346E05B: New device: bitfile=ztex_ufm1_15d4 f_default=200.00MHz f_max=248.00MHz HpC=1.0H
ztex_ufm1_15d4-04A346E05B: MAC address: 0004a346e05b
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=222; 0 bytes got lost): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=222; 0 bytes got lost): Retrying it ...
Warning: High speed FPGA configuration failed, trying low speed mode:Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=222; 0 bytes got lost): Trying low speed mode

I've tried everything I can think of and have read on forums etc.

Bogart

legendary

Activity: 966

Merit: 1000

Quote from: uuidman on September 30, 2012, 02:10:15 PM

My fpgas has really been humming along nice. But now I got this:

ztex_ufm1_15y1-0000000016: Error configuring FPGA 2: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122)
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Retrying it ...
Warning: High speed FPGA configuration failed, trying low speed mode:Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Trying low speed mode
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122):

Im a little unsure, but before if they have been som problems uploading fw, the classic poweroff all pull usb-cables have allways worked and I had that error so few times so Im not sure if its the same errorcode.

I have made numerous restarts and changed cables and so on, I have also reprogrammed a couple of times and tried.
Anyone ?

How are you powering the board? Have you tried a different PS and/or power cable?

uuidman

full member

Activity: 121

Merit: 100

My fpgas has really been humming along nice. But now I got this:

ztex_ufm1_15y1-0000000016: Error configuring FPGA 2: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122)
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Retrying it ...
Warning: High speed FPGA configuration failed, trying low speed mode:Error uploading bitstream: FPGA configuration failed: DONE pin does not go high, possible USB transfer errors (INIT_B_HIST=122): Trying low speed mode
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122): Retrying it ...
Warning: Error uploading bitstream: FPGA configuration failed: DONE pin does not go high (size=4220313 , 0 bytes got lost; checksum=3 , should be 3; INIT_B_HIST=122):

Im a little unsure, but before if they have been som problems uploading fw, the classic poweroff all pull usb-cables have allways worked and I had that error so few times so Im not sure if its the same errorcode.

I have made numerous restarts and changed cables and so on, I have also reprogrammed a couple of times and tried.
Anyone ?

LoBoToMy

newbie

Activity: 9

Merit: 0

"It's working but overheating for some reason. Check the heatsink placement."
I check heatsink, and after this, led1 blinking and board is not detectable over USB (on 12V 4A).
But 7.5V and 1600mA fan slowly rotate and LED1 not blink.

ztex

donator

Activity: 367

Merit: 250

ZTEX FPGA Boards

Quote from: LoBoToMy on September 07, 2012, 05:04:26 PM

LED1 blinking :/
I broke something Sad

Usually indicates an overload / shortcut. But then the board couldn't be detected. (According to https://bitcointalksearch.org/topic/m.1168710 the device is detected).

BR0KK

hero member

Activity: 784

Merit: 500

Set the overheat alarm function to -oh 0.1 (or 0.2)

And try it again:)

pazor

legendary

Activity: 966

Merit: 1000

sell it... Cool

Topic: ZTEX USB-FPGA Modules 1.15x and 1.15y: 215 and 860 MH/s FPGA Boards - page 8. (Read 182450 times)