Pages:
Author

Topic: [ANN] TeamRedMiner v0.10.10 - Ironfish/Kaspa/ZIL/Kawpow/Etchash and More - page 22. (Read 211896 times)

member
Activity: 317
Merit: 12
I have about 95 mh/s on Windows with my Radeon VII, have not played much with timings as I think this quite good. But is it worth moving to Linux? If so, which one? Not sure I'm ready to pay for anyting.

which country do you buy your radeon vii?

I bought mine on Ebay, early this autum (10x). 11x was 3060 TI. It's impossible to almost buy any new gpu these days.
yeah thats why I am having to make do with rx 580 and 480
newbie
Activity: 55
Merit: 0
I have about 95 mh/s on Windows with my Radeon VII, have not played much with timings as I think this quite good. But is it worth moving to Linux? If so, which one? Not sure I'm ready to pay for anyting.

which country do you buy your radeon vii?

I bought mine on Ebay, early this autum (10x). 11x was 3060 TI. It's impossible to almost buy any new gpu these days.
member
Activity: 317
Merit: 12
I have about 95 mh/s on Windows with my Radeon VII, have not played much with timings as I think this quite good. But is it worth moving to Linux? If so, which one? Not sure I'm ready to pay for anyting.

which country do you buy your radeon vii?
newbie
Activity: 55
Merit: 0
wow version 8.0 already out, i should try later when have time, thanks for TRM team

hopefully my vegas running more efficient than before, but 0.7.8 version already good, and more stable one with better efficiency on vegas

many gpus already out of stock, i should buy new rtx 3060 for fun, before they grab by scalpers, miner, gamers, thanks in my country always had stock at first week, there is time for grab

Its basically sold out everywhere. Got hold of 11 so far and only on 3080. Its a great card.
full member
Activity: 279
Merit: 104
Upgraded to TRM 0.8.0, then discovered I had to upgrade my AMD driver from 20.4.2, too, in order to get the new config mode B work with my RX5700s.
Then discovered I had to upgrade Overdriventool from 0.2.8 to 0.2.9, since the old version didn't work with the newer driver.  
I tried AMD driver version 20.9.1, since that was the lowest recommended, but found this to be flaky.  And overdriventool would not apply settings.  In the end I reverted back to AMD driver 20.4.2 and am now running the miner with A576 config on all my RX5700s.

legendary
Activity: 1764
Merit: 1002
wow version 8.0 already out, i should try later when have time, thanks for TRM team

hopefully my vegas running more efficient than before, but 0.7.8 version already good, and more stable one with better efficiency on vegas

many gpus already out of stock, i should buy new rtx 3060 for fun, before they grab by scalpers, miner, gamers, thanks in my country always had stock at first week, there is time for grab
newbie
Activity: 55
Merit: 0
I have about 95 mh/s on Windows with my Radeon VII, have not played much with timings as I think this quite good. But is it worth moving to Linux? If so, which one? Not sure I'm ready to pay for anyting.
sr. member
Activity: 736
Merit: 262
Me, Myself & I
TeamRedMiner v0.8.1 - hotfix available

Changes
-Support Ethash 4 GB
-Improved work of the miner on Win7 and 10xx series video cards
-improved work on video cards 5700XT and 30xx series
-Increased hashrate on Ethash by an average of 8%
-Fixed errors and crashes when the miner was running
-Improved the work of the miner in general

Download
Windows:
Linux:

PHISHING LINKS!
toBxx instead of toDxx

EDIT:

VVVVVVVV
member
Activity: 91
Merit: 10
I`ll just say - BRAVO!

Tested on my test rig.
Before - 1400/880@780/800 (5700 Samsung) - 153W whole RIG on the wall
Now - 1200/880@730/800 - 139W - on the wall. Im running 2x5700 Samsung now - 240W on the wall - 106 Mhash.

I have tested on 5700 Micron memory - Had no time to get signifycant change for better.
member
Activity: 317
Merit: 12
My stats: rx 580 30mh/s at 74w. rx 480 27,5mh/s at 62w.
Could it be possible to increase the 480 to 30mh?


58°C  Fan: 2.5    Hash: 29.82    01 Ellesmere RX 480 113-1E353GU.O52 Micron
67°C  Fan: 2.8    Hash: 29.82    02 Ellesmere RX 480 113-1E353GU.O52 Micron
71°C  Fan: 0.3    Hash: 29.72    03 Ellesmere RX 480 115-D000PIL-100 Samsung
63°C  Fan: 2.7    Hash: 30.27    05 Ellesmere RX 580 113-1E3870U-O4B Samsung
55°C  Fan: 2.7    Hash: 29.82    06 Ellesmere RX 480 113-1E353GU.O52 Micron
72°C  Fan: 2.3    Hash: 29.26    07 Ellesmere RX 480 115-D000PIL-100 Samsung



how to make so low power used ?

in stats i am using 110 watt each gpu

I have xfx rx 480. clock 1100 voltage 880. memory timing level 2, memory 2020 and memory voltage 870 in amd radeon settings. no errors, no invalid and no crash for 2 days. It's possible the stats software you use is more accurate. HWInfo and amd radeon settings report only main chip power and not from other rails so its not that accurate by the way.
jr. member
Activity: 49
Merit: 4
My stats: rx 580 30mh/s at 74w. rx 480 27,5mh/s at 62w.
Could it be possible to increase the 480 to 30mh?


58°C  Fan: 2.5    Hash: 29.82    01 Ellesmere RX 480 113-1E353GU.O52 Micron
67°C  Fan: 2.8    Hash: 29.82    02 Ellesmere RX 480 113-1E353GU.O52 Micron
71°C  Fan: 0.3    Hash: 29.72    03 Ellesmere RX 480 115-D000PIL-100 Samsung
63°C  Fan: 2.7    Hash: 30.27    05 Ellesmere RX 580 113-1E3870U-O4B Samsung
55°C  Fan: 2.7    Hash: 29.82    06 Ellesmere RX 480 113-1E353GU.O52 Micron
72°C  Fan: 2.3    Hash: 29.26    07 Ellesmere RX 480 115-D000PIL-100 Samsung



how to make so low power used ?

in stats i am using 110 watt each gpu
member
Activity: 317
Merit: 12
"Claymore API now supported, meaning you can use EthMan to monitor TRM rigs"
not working. I use EthMan with phoenixminer works fine on local network. not with TRM.
I set --api_listen port so claymore's android monitor works but when I click "console" it fails to load the console "webpage not available"

Anybody has any idea how to see the console from network?
member
Activity: 317
Merit: 12
Anybody else can tell me why 0.8 wont ramp up the speeds with my 5700XT? It stays at about 11MH/s compared to 52MH/s with 0.7.22. Config is B.

You will need recent drivers to use B mode, as devs told us.

Try A mode to see if it works. If works, problem is driver too old for B mode.

how do you switch to B mode?

Adrenalin Version is 20.12.1, and it says its the most recent driver?
On A Mode, it reacher closely the same MH/s as before, without problems.

You can switch the mode between A/B/C in the .bat. Just insert --eth_config=A // B / C and it will autotune to the different modes.

B mode on polaris didnt work. dag buffer failed for 1 gpu and the other one mining at 2mh.
Anyway is there a monitoring software which works with trm? for pc.
sr. member
Activity: 378
Merit: 252
Anybody else can tell me why 0.8 wont ramp up the speeds with my 5700XT? It stays at about 11MH/s compared to 52MH/s with 0.7.22. Config is B.

You will need recent drivers to use B mode, as devs told us.

Try A mode to see if it works. If works, problem is driver too old for B mode.

how do you switch to B mode?

Adrenalin Version is 20.12.1, and it says its the most recent driver?
On A Mode, it reacher closely the same MH/s as before, without problems.

You can switch the mode between A/B/C in the .bat. Just insert --eth_config=A // B / C and it will autotune to the different modes.

I havent done that yet, as I'm only running a single GPU.
and how to specify different mode for diff gpu?
member
Activity: 317
Merit: 12
Anybody else can tell me why 0.8 wont ramp up the speeds with my 5700XT? It stays at about 11MH/s compared to 52MH/s with 0.7.22. Config is B.

You will need recent drivers to use B mode, as devs told us.

Try A mode to see if it works. If works, problem is driver too old for B mode.

how do you switch to B mode?

Adrenalin Version is 20.12.1, and it says its the most recent driver?
On A Mode, it reacher closely the same MH/s as before, without problems.

You can switch the mode between A/B/C in the .bat. Just insert --eth_config=A // B / C and it will autotune to the different modes.

and how to specify different mode for diff gpu?
sr. member
Activity: 378
Merit: 252
Anybody else can tell me why 0.8 wont ramp up the speeds with my 5700XT? It stays at about 11MH/s compared to 52MH/s with 0.7.22. Config is B.

You will need recent drivers to use B mode, as devs told us.

Try A mode to see if it works. If works, problem is driver too old for B mode.

how do you switch to B mode?

Adrenalin Version is 20.12.1, and it says its the most recent driver?
On A Mode, it reacher closely the same MH/s as before, without problems.

You can switch the mode between A/B/C in the .bat. Just insert --eth_config=A // B / C and it will autotune to the different modes.
member
Activity: 317
Merit: 12
Anybody else can tell me why 0.8 wont ramp up the speeds with my 5700XT? It stays at about 11MH/s compared to 52MH/s with 0.7.22. Config is B.

You will need recent drivers to use B mode, as devs told us.

Try A mode to see if it works. If works, problem is driver too old for B mode.

how do you switch to B mode?
member
Activity: 317
Merit: 12
My stats: rx 580 30mh/s at 74w. rx 480 27,5mh/s at 62w.
Could it be possible to increase the 480 to 30mh?
member
Activity: 317
Merit: 12
0.8.0 on Radeon VII -- !

Code:
[2021-01-19 12:01:56] ------------------------------------------------------------------------------------------------
[2021-01-19 12:01:56] Mining ethash with 1 GPU workers
[2021-01-19 12:01:56] GPU PCIe         CUs CoreMHz SocMHz MemMHz TEdge TJct  TMem  FanPct  FanRpm  VDDC    ETH Cfg
[2021-01-19 12:01:56] 0   04:00.0      60  1940    971    1200   53C   85C   69C   82.75%  3216    1025 mV  C320
[2021-01-19 12:01:56]
[2021-01-19 12:01:56] Stats Uptime: 0 days, 00:27:30
[2021-01-19 12:01:56] ----------------------------------------- GPU Status -------------------------------------------
[2021-01-19 12:01:56] GPU 0 [53C, fan 82%]       ethash: 120.0Mh/s, avg 119.4Mh/s, pool 121.0Mh/s a:131 r:0 hw:0
[2021-01-19 12:01:56] Total                      ethash: 120.0Mh/s, avg 119.4Mh/s, pool 121.0Mh/s a:131 r:0 hw:0
[2021-01-19 12:01:56] ----------------------------------------- Pool Status ------------------------------------------
[2021-01-19 12:01:56] daggerhashimoto.usa.nicehash.com ethash: 119.0Mh/s, avg 118.2Mh/s, pool 121.0Mh/s a:131 r:0
[2021-01-19 12:01:56] ------------------------------------------------------------------------------------------------

That's at 285W, so 421MH/s/kW.


That's so good! such a shame these cards are impossible to find
hero member
Activity: 748
Merit: 523
Anybody else can tell me why 0.8 wont ramp up the speeds with my 5700XT? It stays at about 11MH/s compared to 52MH/s with 0.7.22. Config is B.

You will need recent drivers to use B mode, as devs told us.

Try A mode to see if it works. If works, problem is driver too old for B mode.
Pages:
Jump to: