Yep... sent pictures...
Nίκo από πoυ είσαι αδελφέ?
Topic: Announcement: Bitmain launches AntMiner solution, 0.68 J/GH on chip - page 78. (Read 368333 times)
March 14, 2014, 07:40:57 AM
Nίκo από πoυ είσαι αδελφέ?
March 14, 2014, 07:38:21 AM
Yep... sent pictures...
March 14, 2014, 07:21:49 AM
I just received another S1 today and this one was used big time. Lots of Chinese dust all over the PCB boards and fan blades. Should I contact them and have them replace it?
Also might be a sign of things running out and new model coming out.
Also might be a sign of things running out and new model coming out.
You are lucky that your S1 works.
I received heavily used and semi-dead S1 from them.
All covered in dust, heavy smell of burnt electronics, a lot of dead chips - one blade shows 8 ASICs instead of 32.
It hashes only at around 120 GH/s and sometimes just stops hashing with beeping sound, needs power cycle to start again.
I paid 130 euros customs tax for this unit, and it would cost around 200 euros to ship it back to Bitmain and then I have to pay another 130 euros to customs for the replacement unit.
Just does not worth it.
So Bitmain sold me a dead unit and now just stopped responding to my messages.
else i don't belive you at all.
they have 10000 of customers, and no one point that(one blade shows 8 ASICs instead of 32), you are the first one.
or, you didn't buy from https://www.bitmaintech.com , and you got scamed.
March 14, 2014, 01:58:37 AM
I guess I'm getting old - the thought of hooking up 2 computers directly by an ethernet (non-crossover) cable seemed strange to me, but ultimately that's what worked.
Most modern NICS are Auto-MDIX. No need for crossover cables in most cases.
March 14, 2014, 01:44:46 AM
I have plugged my new Antminer S1 in, the sticker on it says to use IP 192.168.1.99; I have setup my gateway mask to allow this network to be routed.
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
sounds like you have not bothered to read/follow the setup guide - follow the guide and you probably will find out what the problem is
Klondike, yes I have bothered and followed the part I needed to follow from Dogies setup guide - since my Ant S1 has the PCIe connectors. PSU is good, router is good, what’s next? I can’t get to the login menu.
You really make it sound like you know what my problem is, so can you write something actually helpful and share this with me please?
Your computer may not be on the same IP and sub net and can not communicate to the Ant. Check the troubleshoot thread sushi has step by step set up.
https://bitcointalksearch.org/topic/setup-troubleshoot-bitmain-antminer-s1-180ghs-miner-344970
I guess I'm getting old - the thought of hooking up 2 computers directly by an ethernet (non-crossover) cable seemed strange to me, but ultimately that's what worked. Well thanks for your excellent link, it worked - so thanks for your help, seeing my first 180 Ghs gives me quite a rush!
March 14, 2014, 01:37:33 AM
I have plugged my new Antminer S1 in, the sticker on it says to use IP 192.168.1.99; I have setup my gateway mask to allow this network to be routed.
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
sounds like you have not bothered to read/follow the setup guide - follow the guide and you probably will find out what the problem is
Klondike, yes I have bothered and followed the part I needed to follow from Dogies setup guide - since my Ant S1 has the PCIe connectors. PSU is good, router is good, what’s next? I can’t get to the login menu.
You really make it sound like you know what my problem is, so can you write something actually helpful and share this with me please?
Your computer may not be on the same IP and sub net and can not communicate to the Ant. Check the troubleshoot thread sushi has step by step set up.
https://bitcointalksearch.org/topic/setup-troubleshoot-bitmain-antminer-s1-180ghs-miner-344970
^this is the sort of pre-requisite reading i meant. Your issue of 'i cant connect' is too vague. I dont know what you have tried or what you havent.
I had read plenty of stuff, probably not the right stuff; meh what counts is that my first Ant works now - yaaaay!
March 14, 2014, 12:28:48 AM
I just received another S1 today and this one was used big time. Lots of Chinese dust all over the PCB boards and fan blades. Should I contact them and have them replace it?
Also might be a sign of things running out and new model coming out.
Also might be a sign of things running out and new model coming out.
You are lucky that your S1 works.
I received heavily used and semi-dead S1 from them.
All covered in dust, heavy smell of burnt electronics, a lot of dead chips - one blade shows 8 ASICs instead of 32.
It hashes only at around 120 GH/s and sometimes just stops hashing with beeping sound, needs power cycle to start again.
I paid 130 euros customs tax for this unit, and it would cost around 200 euros to ship it back to Bitmain and then I have to pay another 130 euros to customs for the replacement unit.
Just does not worth it.
So Bitmain sold me a dead unit and now just stopped responding to my messages.
1) screenshot?
2) what is your PSU - dead chips and rebooting are common signs that your PSU is a bit too weak (you need one rated 550W+ with at least 500W on the 12V rail to run properly)
March 14, 2014, 12:27:28 AM
I have plugged my new Antminer S1 in, the sticker on it says to use IP 192.168.1.99; I have setup my gateway mask to allow this network to be routed.
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
sounds like you have not bothered to read/follow the setup guide - follow the guide and you probably will find out what the problem is
Klondike, yes I have bothered and followed the part I needed to follow from Dogies setup guide - since my Ant S1 has the PCIe connectors. PSU is good, router is good, what’s next? I can’t get to the login menu.
You really make it sound like you know what my problem is, so can you write something actually helpful and share this with me please?
Your computer may not be on the same IP and sub net and can not communicate to the Ant. Check the troubleshoot thread sushi has step by step set up.
https://bitcointalksearch.org/topic/setup-troubleshoot-bitmain-antminer-s1-180ghs-miner-344970
^this is the sort of pre-requisite reading i meant. Your issue of 'i cant connect' is too vague. I dont know what you have tried or what you havent.
March 13, 2014, 10:51:15 PM
I just received another S1 today and this one was used big time. Lots of Chinese dust all over the PCB boards and fan blades. Should I contact them and have them replace it?
Also might be a sign of things running out and new model coming out.
Also might be a sign of things running out and new model coming out.
You are lucky that your S1 works.
I received heavily used and semi-dead S1 from them.
All covered in dust, heavy smell of burnt electronics, a lot of dead chips - one blade shows 8 ASICs instead of 32.
It hashes only at around 120 GH/s and sometimes just stops hashing with beeping sound, needs power cycle to start again.
I paid 130 euros customs tax for this unit, and it would cost around 200 euros to ship it back to Bitmain and then I have to pay another 130 euros to customs for the replacement unit.
Just does not worth it.
So Bitmain sold me a dead unit and now just stopped responding to my messages.
You should send it back but obviously only if they give you RMA number. Return shipping will be their problem and no tax on return either.
March 13, 2014, 08:07:31 PM
I have plugged my new Antminer S1 in, the sticker on it says to use IP 192.168.1.99; I have setup my gateway mask to allow this network to be routed.
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
sounds like you have not bothered to read/follow the setup guide - follow the guide and you probably will find out what the problem is
Klondike, yes I have bothered and followed the part I needed to follow from Dogies setup guide - since my Ant S1 has the PCIe connectors. PSU is good, router is good, what’s next? I can’t get to the login menu.
You really make it sound like you know what my problem is, so can you write something actually helpful and share this with me please?
Your computer may not be on the same IP and sub net and can not communicate to the Ant. Check the troubleshoot thread sushi has step by step set up.
https://bitcointalksearch.org/topic/setup-troubleshoot-bitmain-antminer-s1-180ghs-miner-344970
March 13, 2014, 07:51:41 PM
You should not pay import tax when you receive it back as they will mark it as faulty repair as you have already paid for it...
Did they sent you a new one, if it was heavily used, i am shocked that they did not test it before shipping it out... I hope they will ship a new one very soon and maybe they might be nice enough to throw in few USB miners just a "Sorry, we fucked up by sending you a used miner and we broke our promise"
Did they sent you a new one, if it was heavily used, i am shocked that they did not test it before shipping it out... I hope they will ship a new one very soon and maybe they might be nice enough to throw in few USB miners just a "Sorry, we fucked up by sending you a used miner and we broke our promise"
March 13, 2014, 05:45:55 PM
I just received another S1 today and this one was used big time. Lots of Chinese dust all over the PCB boards and fan blades. Should I contact them and have them replace it?
Also might be a sign of things running out and new model coming out.
Also might be a sign of things running out and new model coming out.
You are lucky that your S1 works.
I received heavily used and semi-dead S1 from them.
All covered in dust, heavy smell of burnt electronics, a lot of dead chips - one blade shows 8 ASICs instead of 32.
It hashes only at around 120 GH/s and sometimes just stops hashing with beeping sound, needs power cycle to start again.
I paid 130 euros customs tax for this unit, and it would cost around 200 euros to ship it back to Bitmain and then I have to pay another 130 euros to customs for the replacement unit.
Just does not worth it.
So Bitmain sold me a dead unit and now just stopped responding to my messages.
March 13, 2014, 05:37:09 PM
i just got 2 new antminers s1, first one is working perfectly, but i cant connect to the other one, when i try to connect to the s1 ip address, it gives me this message:
/usr/lib/lua/luci/dispatcher.lua:211: /etc/config/luci seems to be corrupt, unable to find section 'main'
stack traceback:
[C]: in function 'assert'
/usr/lib/lua/luci/dispatcher.lua:211: in function 'dispatch'
/usr/lib/lua/luci/dispatcher.lua:211: /etc/config/luci seems to be corrupt, unable to find section 'main'
stack traceback:
[C]: in function 'assert'
/usr/lib/lua/luci/dispatcher.lua:211: in function 'dispatch'
SSH to it, change to the /etc/config directory, and see if you have a file called luci that's not empty. If not empty, SSH to the working ANT and compare to it's luci file. Now, to be clear, I'm NOT telling you this will fix it or to even try it but, you could use SSH and SCP to copy the luci file from the working ANT to the broke one and see if that fixes it.
Although the following link has nothing to do with ANTS, it is about openwrt and the same luci error your getting and replacing the luci file with a known good copy worked for these guys. The page is in Chinese so use google translate if you don't speak it.
http://www.right.com.cn/forum/thread-131802-1-1.html
March 13, 2014, 05:13:21 PM
I have plugged my new Antminer S1 in, the sticker on it says to use IP 192.168.1.99; I have setup my gateway mask to allow this network to be routed.
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
sounds like you have not bothered to read/follow the setup guide - follow the guide and you probably will find out what the problem is
Klondike, yes I have bothered and followed the part I needed to follow from Dogies setup guide - since my Ant S1 has the PCIe connectors. PSU is good, router is good, what’s next? I can’t get to the login menu.
You really make it sound like you know what my problem is, so can you write something actually helpful and share this with me please?
March 13, 2014, 04:50:28 PM
I have plugged my new Antminer S1 in, the sticker on it says to use IP 192.168.1.99; I have setup my gateway mask to allow this network to be routed.
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
sounds like you have not bothered to read/follow the setup guide - follow the guide and you probably will find out what the problem is
March 13, 2014, 04:43:45 PM
i just got 2 new antminers s1, first one is working perfectly, but i cant connect to the other one, when i try to connect to the s1 ip address, it gives me this message:
/usr/lib/lua/luci/dispatcher.lua:211: /etc/config/luci seems to be corrupt, unable to find section 'main'
stack traceback:
[C]: in function 'assert'
/usr/lib/lua/luci/dispatcher.lua:211: in function 'dispatch'
/usr/lib/lua/luci/dispatcher.lua:211: /etc/config/luci seems to be corrupt, unable to find section 'main'
stack traceback:
[C]: in function 'assert'
/usr/lib/lua/luci/dispatcher.lua:211: in function 'dispatch'
March 13, 2014, 02:36:58 PM
I have plugged my new Antminer S1 in, the sticker on it says to use IP 192.168.1.99; I have setup my gateway mask to allow this network to be routed.
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
On the Antminer itself I see the ethernet light flickering so it looks alive; but red light is on, on the controller card AND my browser on my computer does not display the Antminer menu page at the sticker address
Please help!!!!!
March 13, 2014, 11:38:18 AM
You have to remember the time difference.
They will ship within 48 hours (2 days from Beijing time). If you ordered it yesterday, most likely your order will be send tomorrow as I am in the same boat... Worst case it will be sent on Saturday buy after so many orders there are yet to fail to ship my order after 48 hours...
Patience you must have my young padawan
They will ship within 48 hours (2 days from Beijing time). If you ordered it yesterday, most likely your order will be send tomorrow as I am in the same boat... Worst case it will be sent on Saturday buy after so many orders there are yet to fail to ship my order after 48 hours...
Patience you must have my young padawan
Its probably in the mail already. The shipping team is fantastic, but they have to manually mark your order as shipped. By the time you get the tracking number, the package will probably be somewhere over the ocean, or just arriving at your customs
thanks, never ordered from them before but heard/read they ship quickly.
March 13, 2014, 11:36:56 AM
How long does it take to ship? I ordered 2 yesterday (12th NA) and promptly paid but it's still sitting as unshipped and I can no longer edit the order...wanted put ship UPS after reading the posts above about DHL. thanks
Order ID
001201403121705042507hkCj2wt06BA
Status
Paid
Unshipped
Valid
Create Time
2014-03-12 17:05:04.0
tx -645de1a27b45cd081461eed0077713e535c5a4c07500cac4f21cc03c061530a9
Order ID
001201403121705042507hkCj2wt06BA
Status
Paid
Unshipped
Valid
Create Time
2014-03-12 17:05:04.0
tx -645de1a27b45cd081461eed0077713e535c5a4c07500cac4f21cc03c061530a9
Its probably in the mail already. The shipping team is fantastic, but they have to manually mark your order as shipped. By the time you get the tracking number, the package will probably be somewhere over the ocean, or just arriving at your customs
March 13, 2014, 11:16:09 AM
It's not a problem if they deliver on time. The only reason so called "pre-mining" is a problem is when manufactures fraudulently advertise and early delivery date and then delay the delivery date in order to charge a higher price and still use the equipment to mine for their own account.
So true. While I would prefer to have an unused miner, the truth is these products aren't going to be running very long. It's very unlikely any pre-mining will effect reliability, and thus customer profits. I just want my unit shipped ASAP, which they do.
Jump to: