I can't login to one C1 and ssh is not responding. I think, I can try to reflash the sd card. How can I do that? I downloaded the firmware already.
THANKS!
Topic: ANTMINER C1 Discussion and Support Thread - page 41. (Read 129188 times)
Fortunately my Fortron 600W (single rail) seems to be more stable than it's bigger brother Raider 750W, I can take 48A continuously from 600W while at this amperage most of Raiders 750W died even they are rated 60A for 750W, but 600W is 42A only.
Interesting, I have completely different experiences with Fortron PSU.All my FSP Fortron Raiders PSU 750W (10units) are working long time ok (each powering 2 units S3+ on default clock), but with all Fortron 600W I had problems...
Do you have to sign in to use the university internet? (Even if you had to just sign once when first setting up pc) If there is a login to use internet this could be a reason for somethings. I have a feeling this could possibly be part of problem.
Dogies idea of proxy should allow you to mine through your PC's connection that is working.
I surely can confirm this is not the case , I'm having I direct connection with no signing page . I'm surfing using the router connection to my labtop as well >
what could be the solution ??
it has to be related to the router because I need to move with my labtop a lot >
Proxy is best solution if you cannot get direct connection.
Does your university have a IT group you can call? (I know alot of university's have students and some staff to help with things such as internet). You could ask them about blocking ports, etc and try to solve it.
How can you go beyond 275M? I'm pretty sure you need to edit /config/cgminer.conf. How do you restart the miner from the command line?
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
This is a bit different than the specs outlined here in the oc thread. https://bitcointalksearch.org/topic/s3-bm1382-overclocking-with-voltage-setting-883197
How does the GH compare based on this?
My OC is also based on BM1382 datasheet and it is in compliance with S3 OC thread...
[/quote]
Do you have to sign in to use the university internet? (Even if you had to just sign once when first setting up pc) If there is a login to use internet this could be a reason for somethings. I have a feeling this could possibly be part of problem.
Dogies idea of proxy should allow you to mine through your PC's connection that is working.
[/quote]
I surely can confirm this is not the case , I'm having I direct connection with no signing page . I'm surfing using the router connection to my labtop as well >
what could be the solution ??
it has to be related to the router because I need to move with my labtop a lot >
Let's see if I can't help you... still waiting on my C1's but been mining for long.
First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
I just got a tp-link router . I connected the miner to it and yes , I'm now able to access to the miner page . First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
but the problem still unsolved : the miner doesn't mine . I'm sure it's connected to the internet .
Is there any special configuration for the pools ??
I'm not really sure if my connection goes through a 80 port . any advice ??
screenshots
http://postimg.org/image/ej19vprbj/
http://postimg.org/image/hh2u35ocv/
http://postimg.org/image/x00a09wnj/
That is more than just internet or other soft problems. You need to reflash the SD card using the image in the #2 post of this thread.
Remove the case, download SD card imager and use it to flash the image here.
can I set my router to route connections to that ssh ??
You might check into your router settings. (Possibly modem depending on connection). I know my ISP had all kinds of blocking with it's default settings. I was able to talk my ISP into making my cable modem into a pass-through mode where my router is in charge of firewall now.
, I don't think I have a lot of options because I'm using a university internet . I don't think I can talk to my ISP . which one you suggest to me : 1- buy a vpn plan 5 usd . (I haven't try rerouting before )
2- buy a internet plan 20 usd . (not sure if isp close ports or no)
Do you have to sign in to use the university internet? (Even if you had to just sign once when first setting up pc) If there is a login to use internet this could be a reason for somethings. I have a feeling this could possibly be part of problem.
Dogies idea of proxy should allow you to mine through your PC's connection that is working.
Let's see if I can't help you... still waiting on my C1's but been mining for long.
First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
I just got a tp-link router . I connected the miner to it and yes , I'm now able to access to the miner page . First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
but the problem still unsolved : the miner doesn't mine . I'm sure it's connected to the internet .
Is there any special configuration for the pools ??
I'm not really sure if my connection goes through a 80 port . any advice ??
screenshots
http://postimg.org/image/ej19vprbj/
http://postimg.org/image/hh2u35ocv/
http://postimg.org/image/x00a09wnj/
That is more than just internet or other soft problems. You need to reflash the SD card using the image in the #2 post of this thread.
Remove the case, download SD card imager and use it to flash the image here.
can I set my router to route connections to that ssh ??
You might check into your router settings. (Possibly modem depending on connection). I know my ISP had all kinds of blocking with it's default settings. I was able to talk my ISP into making my cable modem into a pass-through mode where my router is in charge of firewall now.
, I don't think I have a lot of options because I'm using a university internet . I don't think I can talk to my ISP . which one you suggest to me : 1- buy a vpn plan 5 usd . (I haven't try rerouting before )
2- buy a internet plan 20 usd . (not sure if isp close ports or no)
How can you go beyond 275M? I'm pretty sure you need to edit /config/cgminer.conf. How do you restart the miner from the command line?
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
This is a bit different than the specs outlined here in the oc thread. https://bitcointalksearch.org/topic/s3-bm1382-overclocking-with-voltage-setting-883197
How does the GH compare based on this?
Let's see if I can't help you... still waiting on my C1's but been mining for long.
First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
I just got a tp-link router . I connected the miner to it and yes , I'm now able to access to the miner page . First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
but the problem still unsolved : the miner doesn't mine . I'm sure it's connected to the internet .
Is there any special configuration for the pools ??
I'm not really sure if my connection goes through a 80 port . any advice ??
screenshots
http://postimg.org/image/ej19vprbj/
http://postimg.org/image/hh2u35ocv/
http://postimg.org/image/x00a09wnj/
That is more than just internet or other soft problems. You need to reflash the SD card using the image in the #2 post of this thread.
Remove the case, download SD card imager and use it to flash the image here.
can I set my router to route connections to that ssh ??
You might check into your router settings. (Possibly modem depending on connection). I know my ISP had all kinds of blocking with it's default settings. I was able to talk my ISP into making my cable modem into a pass-through mode where my router is in charge of firewall now.
That is more than just internet or other soft problems. You need to reflash the SD card using the image in the #2 post of this thread.
Remove the case, download SD card imager and use it to flash the image here.
I just found out that my ISP filters all of the ports exept 5 ports 3333 and 80 are not among them . can I mine to 3389 port or I need to use SSH tunnel or VPN service ?? Remove the case, download SD card imager and use it to flash the image here.
can I set my router to route connections to that ssh ??
I'd still try the SD card image first. You may be able to reroute to pool via BFG as a proxy.
Let's see if I can't help you... still waiting on my C1's but been mining for long.
First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
I just got a tp-link router . I connected the miner to it and yes , I'm now able to access to the miner page . First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
but the problem still unsolved : the miner doesn't mine . I'm sure it's connected to the internet .
Is there any special configuration for the pools ??
I'm not really sure if my connection goes through a 80 port . any advice ??
screenshots
http://postimg.org/image/ej19vprbj/
http://postimg.org/image/hh2u35ocv/
http://postimg.org/image/x00a09wnj/
That is more than just internet or other soft problems. You need to reflash the SD card using the image in the #2 post of this thread.
Remove the case, download SD card imager and use it to flash the image here.
can I set my router to route connections to that ssh ??
Let's see if I can't help you... still waiting on my C1's but been mining for long.
First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
I just got a tp-link router . I connected the miner to it and yes , I'm now able to access to the miner page . First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
but the problem still unsolved : the miner doesn't mine . I'm sure it's connected to the internet .
Is there any special configuration for the pools ??
I'm not really sure if my connection goes through a 80 port . any advice ??
screenshots
http://postimg.org/image/ej19vprbj/
http://postimg.org/image/hh2u35ocv/
http://postimg.org/image/x00a09wnj/
That is more than just internet or other soft problems. You need to reflash the SD card using the image in the #2 post of this thread.
Remove the case, download SD card imager and use it to flash the image here.
How can you go beyond 275M? I'm pretty sure you need to edit /config/cgminer.conf. How do you restart the miner from the command line?
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
Yes, there are 64 ASICs and one or more can be worser than the others, so if you want to OC, you need to increase voltage. It is up to everyone if he wants to break RMA and OC his C1. All my miners are working at 0.775 and 815mV with 300MHz clock without x and without excessible HW errors (HW errors <0.0005%)
Fortunately my Fortron 600W (single rail) seems to be more stable than it's bigger brother Raider 750W, I can take 48A continuously from 600W while at this amperage most of Raiders 750W died even they are rated 60A for 750W, but 600W is 42A only.
I did ssh into miner and firstly edited GUI and corrected error in 275MHz showing 2275MHz, then I added lines for increasing frequency, but it was not completely persistent, frequency set last time remained after reboot, but GUI were overwrited by its original version with "2275MHz" bug. So I changed /conf/cgminer.conf and simple pressed save and apply button in GUI which restart cgminer correctly with new config.
SYSCOOLING
What is status of order 2014123011433?
It was shipped on 30,December,by DHL.Do you have the tracking NO?What is status of order 2014123011433?
no i don't, could you please provide? (pm or email)
Thank You
How can you go beyond 275M? I'm pretty sure you need to edit /config/cgminer.conf. How do you restart the miner from the command line?
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
That far out I would make sure to have a cold ambient.
I have not spoke about 2 batch ones for a while. I can say after getting water cooling parts sorted out these machines do run really stable(Note Bitmain was always helpful and pointed me in right directions). I thought it would be a interesting experiment to do a water cooling miner is what sold me on them. I have been lucky to have a cold winter ambient which keeps them in low temps. It is common to see this miner go into days (if not weeks) on uptime.
So long story short
the batch ones are running good and will continue to hash away.
How can you go beyond 275M? I'm pretty sure you need to edit /config/cgminer.conf. How do you restart the miner from the command line?
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
175MHz @ 0.650V : 356W =0.51W/GH
250MHz @ 0.720V : 650W =0.65W/GH
250MHz @ 0.760V : 662W =0.66W/GH
275MHz @ 0.760V : 809W =0.74W/GH
275MHz @ 0.800V : 900W =0.82W/GH
300MHz @ 0.815V : 1052W =0.88W/GH
EDIT: I just saw 2 asics marqued with x after 2 hours at 275M@760 on a miner. I will leave them at stock setting.
Hello guys .
special greetings to Mr. dogie
firstly, I would like to thank you for your great installing guide which helped me a lot to install my c1 miner .
secondly , I realy want your assisstance to make my miner mine .
I'm very new to mining so please have patience guys if you see any silly questions
.
my c1 miner is 2nd batch with cooling kit .
I'm useing 2 cooler master psu's ( 620 watts & 725 watts , 85% efficiency ) to power the miner .
I connected 4 pci's to the miner ( 2 from 620 +2 from 725 in one line ) . the cooling system is working fine .
but the miner is not mining . I connected the miner directly to my labtop using ethernet cable following your guide .
the first thing I've noticed is that If my labtop is connected to the miner with a cable , it can not connect to the internet using wifi .
I logged to the setting page on 192.168.1.99 to change the worker name to my username.1,
then change network settings to dhcb . then I connected the miner to the internet cable but it doesn't mine . I note that when I turn on the miner
it lights red around 1 minute .
I have no idea how to find the miner page after changing the ip adress to dhcb, but I can fing what ip is assigned to my labtop if I connect it to the intenet cable .
special greetings to Mr. dogie
firstly, I would like to thank you for your great installing guide which helped me a lot to install my c1 miner .
secondly , I realy want your assisstance to make my miner mine .
I'm very new to mining so please have patience guys if you see any silly questions
. my c1 miner is 2nd batch with cooling kit .
I'm useing 2 cooler master psu's ( 620 watts & 725 watts , 85% efficiency ) to power the miner .
I connected 4 pci's to the miner ( 2 from 620 +2 from 725 in one line ) . the cooling system is working fine .
but the miner is not mining . I connected the miner directly to my labtop using ethernet cable following your guide .
the first thing I've noticed is that If my labtop is connected to the miner with a cable , it can not connect to the internet using wifi .
I logged to the setting page on 192.168.1.99 to change the worker name to my username.1,
then change network settings to dhcb . then I connected the miner to the internet cable but it doesn't mine . I note that when I turn on the miner
it lights red around 1 minute .
I have no idea how to find the miner page after changing the ip adress to dhcb, but I can fing what ip is assigned to my labtop if I connect it to the intenet cable .
You could look in router for connected devices. Also can use M's program to see antminers on network.
If that fails there is always reset, and as last resort putting the image listed in second post on sd.
Let's see if I can't help you... still waiting on my C1's but been mining for long.
First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
but the problem still unsolved : the miner doesn't mine . I'm sure it's connected to the internet .
Is there any special configuration for the pools ??
I'm not really sure if my connection goes through a 80 port . any advice ??
screenshots
http://postimg.org/image/ej19vprbj/
http://postimg.org/image/hh2u35ocv/
http://postimg.org/image/x00a09wnj/
For tp-link router, try to set static ip address to192.168.0.99 instead of 192.168.1.99
SYSCOOLING
What is status of order 2014123011433?
It was shipped on 30,December,by DHL.Do you have the tracking NO?What is status of order 2014123011433?
no i don't, could you please provide? (pm or email)
Hello guys .
special greetings to Mr. dogie
firstly, I would like to thank you for your great installing guide which helped me a lot to install my c1 miner .
secondly , I realy want your assisstance to make my miner mine .
I'm very new to mining so please have patience guys if you see any silly questions .
my c1 miner is 2nd batch with cooling kit .
I'm useing 2 cooler master psu's ( 620 watts & 725 watts , 85% efficiency ) to power the miner .
I connected 4 pci's to the miner ( 2 from 620 +2 from 725 in one line ) . the cooling system is working fine .
but the miner is not mining . I connected the miner directly to my labtop using ethernet cable following your guide .
the first thing I've noticed is that If my labtop is connected to the miner with a cable , it can not connect to the internet using wifi .
I logged to the setting page on 192.168.1.99 to change the worker name to my username.1,
then change network settings to dhcb . then I connected the miner to the internet cable but it doesn't mine . I note that when I turn on the miner
it lights red around 1 minute .
I have no idea how to find the miner page after changing the ip adress to dhcb, but I can fing what ip is assigned to my labtop if I connect it to the intenet cable .
special greetings to Mr. dogie
firstly, I would like to thank you for your great installing guide which helped me a lot to install my c1 miner .
secondly , I realy want your assisstance to make my miner mine .
I'm very new to mining so please have patience guys if you see any silly questions
. my c1 miner is 2nd batch with cooling kit .
I'm useing 2 cooler master psu's ( 620 watts & 725 watts , 85% efficiency ) to power the miner .
I connected 4 pci's to the miner ( 2 from 620 +2 from 725 in one line ) . the cooling system is working fine .
but the miner is not mining . I connected the miner directly to my labtop using ethernet cable following your guide .
the first thing I've noticed is that If my labtop is connected to the miner with a cable , it can not connect to the internet using wifi .
I logged to the setting page on 192.168.1.99 to change the worker name to my username.1,
then change network settings to dhcb . then I connected the miner to the internet cable but it doesn't mine . I note that when I turn on the miner
it lights red around 1 minute .
I have no idea how to find the miner page after changing the ip adress to dhcb, but I can fing what ip is assigned to my labtop if I connect it to the intenet cable .
You could look in router for connected devices. Also can use M's program to see antminers on network.
If that fails there is always reset, and as last resort putting the image listed in second post on sd.
Let's see if I can't help you... still waiting on my C1's but been mining for long.
First of all, I figure you changed from Static to DCHP, well, the miner needs an antenna if you go DHCP (WiFi)
Secondly, to access the computer, you need be on the same subnet as the miner.
Manually change your computer's IP to 192.168.1.199 (Yes, .1.199)
You should now be able to access your miner's interface.
However you still need to directly connect to the miner itself to change its settings... you will need an ethernet cable and a router/switch.
Sometimes you can connect directly to the miner sometimes you can't, via ethernet cable... (I never use DHCP)
If it don't work directly or with a router though, you will need a switch... you may need to even change your router's IP address since some routers use 192.168.1.1 as default address which often conflicts with a mining network.
Personally, I cannot connect directly to my miners and have no idea why but works through a switch or router.
If you go buy a switch make sure you get a big enough one you can grow into with GigaBit (10/100/1000) ethernet. (No pun intended)
I got a 24 port Rosewill, has a 5 year warranty and costs around $100, tough and does its job perfectly and then some.
but the problem still unsolved : the miner doesn't mine . I'm sure it's connected to the internet .
Is there any special configuration for the pools ??
I'm not really sure if my connection goes through a 80 port . any advice ??
screenshots
http://postimg.org/image/ej19vprbj/
http://postimg.org/image/hh2u35ocv/
http://postimg.org/image/x00a09wnj/
Odd. I ssh'd into the C1 some time back and changed the root password using the unix command passwd, logged out and logged back in using the new password. Today I went to log in and the password had reverted to admin while the GUI was still connected and unchanged.
Reported to engineers, thanks
Engineer:
Quote
Only the data under /config can be updated. After you update the password, please run below command, the issue will be fixed.
cp -rf /etc/shadow /config/
cp -rf /etc/shadow /config/
Thanks.
Jump to: