Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 68. (Read 125911 times)

Naw, I read a lot more, and I did it, Ran fine on default at 20.5 G/H

I am very new to this, My first Machine, sorry. And as I understand, I BOUGHT THE WRONG ONE, until DASH is 1500 at least... But I am in it for the long haul! in Good ol, BT Macedonia.

Solar mining 101:

I played with it, weirdly a lot of Heat warnings on 544 setting, But oddly, it was on only one string, and it had the coolest temps..... I was considerring leaving it until i saw 45 warnings. But temps were ok, lower than the other (Outside) strings.

Being on Solar you are gods gift to me, as you can imagine. 9Lowering my power usage at will, will change my mining life. Thanks again!

I humbly ask your opinion:

I have settled for these settings, as I have extra power during the day, and cheaper, but still costly, electricity at night:

 During sunlight 525M and I get 19.7G/H Power I am sure 1350Watt

(Thinking of overclocking during those times in the winter at least, what do you think?)

What is the coolest 22G/H setting you can tell me?

 Cloudy: 450 range  and I get 17.5G/H and 1080 watts

Nighttime: 420 range: and I get 16.7G/H and about 840 watts.

Where you from? I owe you two beers now!

Marty

Nice find! Thanks for trying these out. Let us know the results if you got them 

Yes, I think I found one:
http://noctua.at/en/products/product-line-industrial/nf-f12-industrialppc-3000-pwm

This one looks quite promising actually. I just ordered some (they are not cheap!) and I'll give them a try over the weekend...

hi Marty, if you're on 26/11 I suggest you to wait for 29/11, otherwise update to 28/11 (and optionally disable the reboot on low hashrate detection as it's a bit sensitive)

I run it with the 120mm 2000rpm Scythe Slip Stream fans, but that only works if you run it at the lowest voltage setting. A relative silent 2500 to 3000rpm would be better. Anybody got suggestions?

Just installed the 28/11 update, hashrate seems down slightly compared to 26/11 but it's within margins of error.  However I am no longer seeing the dev pools in the miner status, are they hidden now or did you forget to include them?

Hi @all,

as probably some of you have exchanged fans - what kind of model / type would you guys recommend? How many RPM fans are you using to get the D3 quiet?
Mine are currently running at 2500-3000rpm with original fans. Any recommendations?

And thanks Blissz, for starting this and still working on an even better custom FW. :-)

Hi all
thanks god and blissz for this firmware..
yesterday i received the invoice from antminer about my fucking D3..

At the moment i spent 1500USD plus 70 for shipping cost and probably when D3 arrive, i have to pay also the custom fee

As You know there is a way to return of investment by using this new amazing firmware?

i really don't know if is good to check it out from the customs

with this firmware which is the ROI? (at the moment?)

you know if is possible (in the future) improve the hash power?

thankyou guy and THANKYOU blissz

I am thinking wait.

I am currently getting about 12 a day from one D3, running on Solar Power.

I need to bring down the power consumption if I want to add another miner.

and I think this is exactly what we all need.

Blissz! Thanks again!!!

Marty

Lol, look at this chains. Big difference, but chain 1 is the one that sometimes fails 55/60 chips...

https://drive.google.com/open?id=1a6s8MMRm1TkRiRhhkXtmXD04Ioq6JVah

Hi, New member, been reading.

One question for today:

28/11 today, YES or no?

Should I do it, or await 29/11?

BTW BLISSZ

Lets have a Beer someday after we are all rich and can still hear eachother. THANK YOU!

Marty

PS as I see it I only have to disable the "automatic reboot on low hashrate detection / asic failure". to ensure a good quiet working machine, right?

Thanks for your response in advance.

Marty

Yes it seems a bit sensitive, I am now testing an update which only reboots after two consecutive failures.
By the way there is no need to flash back, just disable the automatic reboot option for now.

I went back to the old firmware for now... I noticed that it was rebooting every couple of hours as well.

This is not the firmware, unfortunately its the hashing boards which behave a very little bit different each reboot. My advice: don't bother those 8 HW errors as it's still very little or increase the voltage one step for that board.

Probably. Some things have changed into firmware

after the new update I went from 0 HW Errors for 26 hours to 8 HW Errors in the last 3 hours. Also it seems that it rebooted both miners on its own. Do I need to readjust the settings for the new cgminer?

https://www.inginer.xyz/ only days old and owned by https://www.facebook.com/stefan.schimbator

IF IT IS A SCAM.... do a better job bruh. you don't want people coming after you later.

I did that. With option DISABLED, everything seems fine...prob when switching pools D3 falls under those 15732 Gh/s trigger.
I saw abnormal restarts aswell this morning. We need to adjust restart "if" conditions a bit

Nov 29 07:24:26 (none) local0.err cgminer[10724]: low hashrate detection trigger: 15732.000000 Gh/s
Nov 29 07:24:26 (none) local0.notice cgminer[10724]: set voltage = 1198.763842  real:225 mv
Nov 29 07:24:26 (none) local0.notice cgminer[10724]: set_PIC16F1704_voltage_new ok, voltage = 0xe1
Nov 29 07:24:27 (none) local0.notice cgminer[10724]: set_PIC16F1704_voltage_new ok, voltage = 0xd7
Nov 29 07:24:27 (none) local0.notice cgminer[10724]: set_PIC16F1704_voltage_new ok, voltage = 0xe1
Nov 29 07:24:27 (none) local0.err cgminer[10724]: cgminer time error total_secs = 1511940267.915820 last_total_secs = 1.000000
Nov 29 07:24:28 (none) local0.warn cgminer[10724]: Pool 0 stratum+tcp://hub.miningpoolhub.com:17007 alive, testing stability
Nov 29 07:24:28 (none) local0.warn cgminer[10724]: Switching to pool 0 stratum+tcp://hub.miningpoolhub.com:17007
Nov 29 07:24:33 (none) local0.warn cgminer[10724]: API running in IP access mode on port 4028 (16)
Nov 29 07:26:05 (none) local0.warn cgminer[10724]: Switching to pool 3 stratum+tcp://dash.suprnova.cc:9995
Nov 29 07:27:55 (none) local0.warn cgminer[10724]: Switching to pool 0 stratum+tcp://hub.miningpoolhub.com:17007

LOL, i just set to the frequency to 425, my third chain and second chain are starting to give HWs, and the third chain shows some xxx

Do i have to reboot the miner after change something?
[/quote]

Try to play with voltages. No need to reboot, restart miner is ok. That happens when you hit Save&Apply button