Stupid question, at 444Mhz, whats your outlet power usage?
I'm not getting anything lower than 900, using the lowest voltage settings
Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 70. (Read 125911 times)
Hi Bliss, the chip temperatures are wacky with this new update. It either shows very low or high temps on one chain, 14 or 125 degrees C. Every time I reboot the miner it will change between low or high temps.
Hi,
noticed again 0.000 hash with 55/60 chips alive on one board.
No restart with latest version. Probably because of missing xxxxx....
Kernel log attached, as promised
https://drive.google.com/open?id=1cqlZkDF6rBW8uKWeMkU2Zj1MAzS_oTdI
noticed again 0.000 hash with 55/60 chips alive on one board.
No restart with latest version. Probably because of missing xxxxx....
Kernel log attached, as promised
https://drive.google.com/open?id=1cqlZkDF6rBW8uKWeMkU2Zj1MAzS_oTdI
Seriously if you want to throw bitcoins away on a scam I would be happy to send you a Bitcoin address to send it to.
These guys literally started this site TODAY. This has SCAM written all over. Most likely it's the inginer.xyz guys realizing they have been marked as a scam and starting a new shop... Or someone else seeing all the traffic and going to try their had at scamming people.
If it's too good to be true ( ehm.. D3
However Blissz stuff is Majorly AWESOME!!!
Before this latest version I was getting 18.5mhs @1100w, now I'm at 19.5 (sometime 20) @1099w.
Great stuff here!!
its SCAM
Hello blissz I've read a few posts and see you do a great job, I wanted to ask you there will be a chance to add new algorithms? or change from x11 to scrypt?
can you put a switch to change pools like in the baikal and add some of the others? thanks and sorry for my english.
can you put a switch to change pools like in the baikal and add some of the others? thanks and sorry for my english.
I will wait for an even more stable version to upgrade. thanks for your job.
Some questions Blissz, is your latest firmware supporting extranonce.subscribe? You know the #xnsub at the end.
What causes loosing network connection?
What causes loosing network connection?
I checked the code it does an extranonce_subscribe_stratum(pool), so support is there.
Loosing network for a long time (i.e. disconnect the cable) for more then 2 minutes doesn't shut off the miner currently. This makes sense for the long bitcoin block times maybe, but not for mining most of the x11 coins as their block times are short.
I do want to change this or make it optional, to temporary shut off the mining boards until the network connection gets back.
Some questions Blissz, is your latest firmware supporting extranonce.subscribe? You know the #xnsub at the end.
What causes loosing network connection?
What causes loosing network connection?
Anyone else having problems with one of their chains just showing no Hash Rates? just shows 0000
It probably shows hardware errors too on that chain? I think it's clocked to high for the amount of voltage set.
It does show a lot of hardware errors, but I've even had it on 100M and the lowest Volt settings.. tried several options and still it shows 0000... If I am lucky and reboot it works for few seconds to hash and then goes back to 0000 Hash Rates.
If I flash back to the Bitmain firmware it works fine though?
That board needs more voltage I guess. Just set the voltage for that board a bit higher. Make sure to flash the firmware I just posted. It might help as well
v1.0 :: 28/11 :: RECOMMENDED UPDATE
Download:
https://mega.nz/#!rgR1RCpS!aoBjx2kZduOS23KFzS_0jUHhw4-SWfs23BYLL2SZJC8
Changes 28/11:
- Fixed the automatic reboot on low hashrate or high ASIC fail rate.
- updated cgminer to v4.10 (for details see: https://bitcointalksearch.org/topic/m.17594456)
- improved pool switching behavior
- improved startup stability of all chains
- cgminer binary optimizations
know issues:
- switching pools can sometimes cause the miner to wait for work for ~5 seconds. (improved from ~10 seconds)
- loosing network connection doesn't stop the mining boards properly (this is default bitmain behavior, but I don't like it, so it will be changed in the future)
happy mining!
Download:
https://mega.nz/#!rgR1RCpS!aoBjx2kZduOS23KFzS_0jUHhw4-SWfs23BYLL2SZJC8
Changes 28/11:
- Fixed the automatic reboot on low hashrate or high ASIC fail rate.
- updated cgminer to v4.10 (for details see: https://bitcointalksearch.org/topic/m.17594456)
- improved pool switching behavior
- improved startup stability of all chains
- cgminer binary optimizations
know issues:
- switching pools can sometimes cause the miner to wait for work for ~5 seconds. (improved from ~10 seconds)
- loosing network connection doesn't stop the mining boards properly (this is default bitmain behavior, but I don't like it, so it will be changed in the future)
happy mining!
Hello blissz I've read a few posts and see you do a great job, I wanted to ask you there will be a chance to add new algorithms? or change from x11 to scrypt?
can you put a switch to change pools like in the baikal and add some of the others? thanks and sorry for my english.
can you put a switch to change pools like in the baikal and add some of the others? thanks and sorry for my english.
Anyone else having problems with one of their chains just showing no Hash Rates? just shows 0000
It probably shows hardware errors too on that chain? I think it's clocked to high for the amount of voltage set.
It does show a lot of hardware errors, but I've even had it on 100M and the lowest Volt settings.. tried several options and still it shows 0000... If I am lucky and reboot it works for few seconds to hash and then goes back to 0000 Hash Rates.
If I flash back to the Bitmain firmware it works fine though?
Anyone else having problems with one of their chains just showing no Hash Rates? just shows 0000
It probably shows hardware errors too on that chain? I think it's clocked to high for the amount of voltage set.
Anyone else having problems with one of their chains just showing no Hash Rates? just shows 0000
Hey Blissz
Can you do a change from pool to pool without rebooting?
Can you do a change from pool to pool without rebooting?
changing pools/order doesn't reboot, just restarts cgminer
Hey Blissz
Can you do a change from pool to pool without rebooting?
Can you do a change from pool to pool without rebooting?
With this firmware ...does anyone tried to use a different PSU ?? Less than 1600 w?
Could I use a 1200 or 1k ?
im using a 1000watt for mineCould I use a 1200 or 1k ?
At the lowest voltage setting at ~15 / 16GH/s/s you can run it at 750watt - 800watt. So my advice would be to have at least a 900+ watt power supply for this.
Make sure not to connect al boards as you're still on the stock firmware, otherwise you'll blow the PSU. First flash it / set it to the lowest voltage / 400Mhz and then connect all the boards.
I need you help!
After I updated the software to dig other coins, mine machine crashed can not log in!
After I updated the software to dig other coins, mine machine crashed can not log in!
D3 only can dig dash?
D3 only can dig dash?i'm flashed your firmware ,changed to dig onixcoin.it's can not log in
Every x11 coin should work. Seems like you had a bad flash for some reason. Please make sure to download the firmware again and try the recovery method as posted.
I need you help!
After I updated the software to dig other coins, mine machine crashed can not log in!
After I updated the software to dig other coins, mine machine crashed can not log in!
D3 only can dig dash?
D3 only can dig dash?i'm flashed your firmware ,changed to dig onixcoin.it's can not log in
[/quote]
Jump to: