Antminer D3 Blissz firmware (10/12 v1.12 update) - page 69.

fecell

jr. member

Activity: 136

Merit: 2

Quote from: may142012 on November 29, 2017, 01:23:48 AM

Can you add an option to power off the miner, so you don't have to unplug the cable cord immediately.

it's impossible.
hash blades powering directly from PSU. it can't be power off by control board.

blissz

sr. member

Activity: 336

Merit: 258

Quote from: dalu1 on November 28, 2017, 10:37:00 PM

Blissz,

Your newest firmware 28/11 crashes right after 2 hours when it tries to switch from pool 3 to pool 0. I am flashing back to your 26/11 version.

Can you try to flash 28/11 again and disable the "automatic reboot on low hashrate detection / asic failure". Please pm the last ~100 lines of the kernel log after a few hours of hashing if you do.

blissz

sr. member

Activity: 336

Merit: 258

Quote from: SimpleCoin8 on November 28, 2017, 07:33:21 PM

Hi Bliss, the chip temperatures are wacky with this new update. It either shows very low or high temps on one chain, 14 or 125 degrees C. Every time I reboot the miner it will change between low or high temps.

version 26/11 was ok for you?
https://mega.nz/#!f5hhlKzQ!b9I4qRJfROD9trRuJ5IH-B3FZcPe_-FjZRJS7u_tWRE

may142012

member

Activity: 301

Merit: 10

Can you add an option to power off the miner, so you don't have to unplug the cable cord immediately.

dalu1

member

Activity: 83

Merit: 10

Performing it is a better way of learning things

Blissz,

I have suggestion, can you auto tune the hashrate some thing like when a chain error rate exceeds 5 (x) errors per minutes, decrease the hashrate by 1 (x/5) meg until it is stable starting from the configured hashrate.

dalu1

member

Activity: 83

Merit: 10

Performing it is a better way of learning things

Quote from: may142012 on November 28, 2017, 10:38:43 PM

Is everyone experiencing low hash rates monitored from the pool you are using? My miner's showing 14,837 MH/s, but on my pool, it is showing me incorrect hash rate like under 10,000 MH/s below my miner's hash rates.

Pool monitor rate varies in a range around your miner's reported hashrate. Normally slightly lower, but not much.

may142012

member

Activity: 301

Merit: 10

Is everyone experiencing low hash rates monitored from the pool you are using? My miner's showing 14,837 MH/s, but on my pool, it is showing me incorrect hash rate like under 10,000 MH/s below my miner's hash rates.

dalu1

member

Activity: 83

Merit: 10

Performing it is a better way of learning things

Blissz,

Your newest firmware 28/11 crashes right after 2 hours when it tries to switch from pool 3 to pool 0. I am flashing back to your 26/11 version.

tperalta82

full member

Activity: 174

Merit: 100

Quote from: may142012 on November 28, 2017, 08:23:49 PM

Quote from: tperalta82 on November 28, 2017, 08:13:15 PM

Quote from: may142012 on November 28, 2017, 08:10:33 PM

Quote from: tperalta82 on November 28, 2017, 08:09:19 PM

Quote from: may142012 on November 28, 2017, 08:06:07 PM

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt

Ok, what's about voltage? Should i leave it "Lowest"? Auto default fans?

Yes, if it works stable like that, just keep those values

LOL, i just set to the frequency to 425, my third chain and second chain are starting to give HWs, and the third chain shows some xxx

Do i have to reboot the miner after change something?

strange, what PSU are you running?

Wananavu99

full member

Activity: 345

Merit: 131

Quote from: ruptan on November 28, 2017, 07:57:49 PM

Quote from: ?? on ??

hi all

does anyone know why people seem to be selling their d3's cheaper than you can buy them from bitmain on ebay?

Simple. It not profitable anymore. Stop buying Antminers!!

I agree. I racked up a large bill this black Friday, buying several GPUs, 1 mobo and other mining hardware. Cyber monday sucked bad, not much deals at all.

may142012

member

Activity: 301

Merit: 10

Quote from: tperalta82 on November 28, 2017, 08:13:15 PM

Quote from: may142012 on November 28, 2017, 08:10:33 PM

Quote from: tperalta82 on November 28, 2017, 08:09:19 PM

Quote from: may142012 on November 28, 2017, 08:06:07 PM

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt

Ok, what's about voltage? Should i leave it "Lowest"? Auto default fans?

Yes, if it works stable like that, just keep those values

LOL, i just set to the frequency to 425, my third chain and second chain are starting to give HWs, and the third chain shows some xxx

Do i have to reboot the miner after change something?

tperalta82

full member

Activity: 174

Merit: 100

Quote from: may142012 on November 28, 2017, 08:10:33 PM

Quote from: tperalta82 on November 28, 2017, 08:09:19 PM

Quote from: may142012 on November 28, 2017, 08:06:07 PM

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt

Ok, what's about voltage? Should i leave it "Lowest"? Auto default fans?

Yes, if it works stable like that, just keep those values

may142012

member

Activity: 301

Merit: 10

Quote from: tperalta82 on November 28, 2017, 08:09:19 PM

Quote from: may142012 on November 28, 2017, 08:06:07 PM

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt

Ok, what's about voltage? Should i leave it "Lowest"? Auto default fans?

tperalta82

full member

Activity: 174

Merit: 100

Quote from: may142012 on November 28, 2017, 08:06:07 PM

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt, as for the HW errors, i wouldn't be concerned with those values

may142012

member

Activity: 301

Merit: 10

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

tperalta82

full member

Activity: 174

Merit: 100